i-Series User Manual – v2.0 i-1 i-2 i-8 i-12 EM Acoustics Loudspeakers Building 74, Dunsfold Park Cranleigh, Surrey GU6 8TB, UK Phone +44 (0) 1483 266520 Fax +44 (0) 1483 275619 www.emacoustics.co.uk _________________________________________________________________________________________ Copyright EM Acoustics 2006 1 i-Series User Manual www.emacoustics.co.
CONTENTS Introduction Thank you ...…………………………………………………………………………………………………………………… 3 Unpacking ………………………………………………………………………………………………………………………. 3 Declaration of Conformity ……………………………………………………………………………………………… 3 Product Range Overview i-1 ultra-compact satellite enclosure …………….……………………………………………………………….4 i-2 ultra-compact fullrange enclosure …………………………………………………………………………….4 i-8 ultra-compact subwoofer enclosure ………………………………………………………………………….5 i-12 compact subwoofer enclosure …………………………………………………………………………….….
INTRODUCTION Thank you Thank you for purchasing a product from the i-Series from EM Acoustics. The i-Series products have been carefully designed and rigorously tested to ensure years of flawless operation and unprecedented sonic quality. Designed primarily for discreet installation use, the i-Series products find applications from cafes and bars through to museums, nightclub infills and themed attractions.
PRODUCT RANGE OVERVIEW i-1 Ultra-Compact Satellite Loudspeaker The i-1 is a compact, satellite mid/high loudspeaker, designed for a wide variety of discreet sound reinforcement applications from museums and themed attractions through to infills in nightclubs and bars. It contains a single 4” (102mm) titanium cone drive unit, with integral passive circuitry for unprecedented sonic performance from an enclosure type where compromises are usually made.
i-8 compound isobaric subwoofer The i-8 is a subwoofer designed to create the depth and authority in low frequencies that is normally associated with large systems, but in a compact package for ease of installation. Consequently, the i-8 has a frequency response down to 35Hz yet is small enough to be concealed underneath sofas or in small wall cavities.
SYSTEM SET-UP Safety Considerations Loudspeaker systems are potentially dangerous objects if used incorrectly. Please ensure that you read this section fully, and contact EM Acoustics or your local dealer should you be in any doubt over correct operation procedures. Professional loudspeaker systems are capable of producing damage-inducing sound pressure levels, and hence care should be taken when setting your system up, particularly when it comes to loudspeaker placement within a venue.
personnel following safe working practice. Should you be in any doubt whatsoever, please contact your local dealer who will be able to refer you to a suitable rigging company.
MOUNTING & RIGGING OPTIONS Rigging Hardware & Accessories The i-Series loudspeakers have a range of integral rigging hardware to enable usage in a wide variety of ways. The i-1 is supplied with four M5 fixings (one on each side of the enclosure) and a steel yoke. This steel yoke attaches to either pair of fixings to provide pan & tilt options.
Attachment and Adjustment of the YK-i1 yoke The i-1 ships with the YK-i1 yoke attached in the normal operating plane. Should you wish to rotate the yoke (for example to utilise the trapezoidal enclosure shape to fit the i-1 closer into a corner), remove the two countersunk M5 machine screws in the enclosure, and remove the M5 socket-head bolts holding the yoke in place. The yoke can then be rotated and the bolts reinstated in the alternative points.
Attachment of the YK-i2h horizontal hanging yoke With the i-2 lying on its side, remove the two countersunk M10 fixings in the ends of the enclosure (marked “A” in Fig 1) and put them in a safe place. Position the YK-i2h over the enclosure, insert the knurled plastic knobs into the holes and tighten securely. There are three possible positions for an attachment device – only the central point (marked “B”) should ever be used by itself.
Installation of the DA-1 Power Amplifier Module The i-12 subwoofer can accept the EM Acoustics DA-1 digital power amplifier module. One DA-1 is used to drive one i-12, and in this configuration the DA-1 runs in two channel mode, with each pair of drive units driven by one channel. To install the DA-1, lie the enclosure on its front. Using a 4mm Allen Key, carefully undo the six M5 socket head bolts holding the connector panel door in place on the rear of the enclosure.
MAINTENANCE Your EM Acoustics loudspeakers have been rigorously tested before they leave our factory, to ensure that they give you a lifetime of flawless operation. Should any of your drive units fail and need replacing, please follow the guidelines below. i-1: Fullrange Drive Unit 1. Using a No.2 Pozidrive screwdriver, remove the four pan-head screws that hold the front grille in place.
4. To reinstate the driver, simply reverse the above procedure. Please observe the correct polarity – white cable to positive terminal, yellow cable to negative. 5. Follow the procedure outlined above to replace the front grille. i-8: Front Low Frequency Drive Units 1. Carefully remove the foam from the grilles – it is held in place with Velcro fasteners. Using a No.
i-12: Front Low Frequency Drive Units 1. Carefully remove the foam from the grilles – it is held in place with Velcro fasteners. Using a No.2 Pozidrive screwdriver, undo the Pozidrive screws holding each grille in place, then remove the grilles to gain access to the drive units. 2. Using a 10mm socket, undo the four M6 Nyloc nuts holding the drive unit in place.
WARRANTY Limited Warranty This EM Acoustics loudspeaker product is warranted to the original end-user purchaser and all subsequent owners for a period of three years from the original date of purchase. Warranty Coverage This warranty covers defects in materials and workmanship. It does not include: • Damage or failure caused by accident, misuse, neglect, abuse or modification by any person other than an authorised EM Acoustics representative.
APPENDIX A – TECHNICAL SPECIFICATIONS EM Acoustics operates a continuous process of research and development, and as such reserves the right to alter specifications without notice. i-1 Enclosure Type: compact fullrange enclosure Dimensions (HxWxD, mm/ins): 130/5.1 x 130/5.1 x 167/6.
i-2 Enclosure Type: compact fullrange enclosure Dimensions (HxWxD, mm/ins): 151/5.9 x 470/18.5 x 192/7.6 Net Weight: 9kg Frequency Response (+/- 3dB): 90Hz – 18KHz Sensitivity: 91dB, 1W/1m Dispersion: 90°H x 20°V (rotatable) Drive Units: 2 x 5” (127mm) LF/MF cone drive units 1 x 1” x 4” planar wave HF drive unit Power Handling: 200W RMS, 400W Program Maximum SPL: 110dB continuous, 116dB peak Nominal Impedance: 4 ohms Crossover: Uniphase Internal Passive.
i-8 Enclosure Type: compound isobaric subwoofer Dimensions (HxWxD, mm/ins): 308/12.1 x 530/20.9 x 450/17.
i-12 Enclosure Type: compound isobaric subwoofer Dimensions (HxWxD, mm/ins): 420/16.5 x 823/32.3 x 700/27.