MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page b Wednesday, August 19, 2009 5:06 PM Copyright © 2009. All Rights Reserved. eMachines User Guide Original Issue: 06 / 2009 Model number: __________________________________ Serial number: ___________________________________ Purchase date: ___________________________________ Place of purchase: ________________________________ Visit http://registration.emachines.com and discover the benefits of being an eMachines customer.
MU0000000_eM_ENG_V09A3.book Page i Wednesday, August 19, 2009 5:06 PM Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
MU0000000_eM_ENG_V09A3.book Page ii Wednesday, August 19, 2009 5:06 PM : • Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, HDD, Optical drive, and even exposure risk from lithium battery pack. Safe listening Follow these instructions, suggested by hearing experts,to protect your hearing. • Gradually increase the volume until you can hear it clearly and comfortably and without distortion.
MU0000000_eM_ENG_V09A3.book • Page iii Wednesday, August 19, 2009 5:06 PM Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.
MU0000000_eM_ENG_V09A3.book Page iv Wednesday, August 19, 2009 5:06 PM : Mercury advisory For projectors or electronic products containing an LCD/CRT monitor or display: Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal information, check www.lamprecycle.org.
MU0000000_eM_ENG_V09A3.book Page v Wednesday, August 19, 2009 5:06 PM Tips and information for comfortable use Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of physical injury.
MU0000000_eM_ENG_V09A3.book Page vi Wednesday, August 19, 2009 5:06 PM : • Blink frequently to keep your eyes from drying out. Display • Keep your display clean. • Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. • Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity.
MU0000000_eM_ENG_V09A3.book Page vii Wednesday, August 19, 2009 5:06 PM Contents Chapter 1: Checking Out Your Computer . . . 1 About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 2: Setting Up and Getting Started. . . . . . .
MU0000000_eM_ENG_V09A3.book Page viii Wednesday, August 19, 2009 5:06 PM Contents Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Expansion cards . . . . . . . . . . . . . . . . . . . . . . . . . . File management . . . . . . . . . . . . . . . . . . . . . . . . . Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page 2 Wednesday, August 19, 2009 5:06 PM Chapter 1: Checking Out Your Computer About this guide This guide includes information and maintenance instructions that are specific to your model of computer. Some illustrations in this guide may look different than your computer because hardware options and port locations may vary. Product Registration When using your computer for the first time, it is recommended that you immediately register it.
MU0000000_eM_ENG_V09A3.book Page 3 Wednesday, August 19, 2009 5:06 PM Front Component Icon Description DVD/CD drive Use this drive to listen to audio CDs, install games and programs, watch DVDs, and store large files onto recordable discs (depending on drive type). This drive may be a CD, recordable CD, DVD, recordable DVD, Blu-ray, or HD DVD drive. Memory card reader Insert a memory card from a digital camera, MP3 player, PDA, cellular telephone, or other device into the memory card reader.
MU0000000_eM_ENG_V09A3.book Page 4 Wednesday, August 19, 2009 5:06 PM Chapter 1: Checking Out Your Computer Back Important Your computer’s hardware options and port locations may vary from this illustration. Component Icon Description Kensington lock slot (optional) Connects to a Kensington-compatible computer security lock. Voltage switch The switch is preset at the factory. Make sure that this is set to the correct voltage for your area.
MU0000000_eM_ENG_V09A3.book Page 5 Component Wednesday, August 19, 2009 Icon 5:06 PM Description Center/subwoofer jack (orange plug) (optional) Plug your center speaker and subwoofer into this jack. Surround L/R speaker jack (black plug) Plug your rear right and left speakers into this jack.
MU0000000_eM_ENG_V09A3.
7 MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page 8 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started Working safely and comfortably Before using your computer, follow these general guidelines for setting up a safe and comfortable work area and avoiding discomfort and strain: • Keep hands and arms parallel to the floor. • Adjust the screen so it is perpendicular to your line of sight, and the top of the screen is no higher than eye leve. • Place your feet flat on the floor or on a footrest.
MU0000000_eM_ENG_V09A3.book Page 9 Wednesday, August 19, 2009 5:06 PM Preparing power connections Protecting from power source problems Warning High voltages can enter your computer through both the power cord and the modem connection. Protect your computer by using a surge protector. If you have a telephone modem, use a surge protector that has a modem jack. If you have a cable modem, use a surge protector that has an antenna/cable TV jack.
MU0000000_eM_ENG_V09A3.book Page 10 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started Checking the voltage selection Caution If you set the voltage selection switch incorrectly, your system will be damaged. Make sure this switch is set correctly for your location before turning on your computer. In the United States, the utility power is supplied at a nominal 115 volts at 60 Hz.
MU0000000_eM_ENG_V09A3.book Page 11 Wednesday, August 19, 2009 5:06 PM Connecting to a broadband modem or network Important Your computer may be equipped with a built-in Ethernet (network) jack. For information about setting up a wired or wireless Ethernet network. You can connect your computer to a cable or DSL (broadband) modem or to a wired Ethernet network.
MU0000000_eM_ENG_V09A3.book Page 12 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started 2 Insert the other end of the modem cable into a telephone wall jack. (The modem will not work with digital or PBX telephone lines.) 3 If you want, you can connect a telephone to the PHONE jack on the modem on the back of your computer. Using the World Wide Web The World Wide Web is a multimedia window to the Internet that gives you access to millions of information sources.
MU0000000_eM_ENG_V09A3.book Page 13 Wednesday, August 19, 2009 5:06 PM Connecting to a Web site After you set up an account with an Internet service provider (ISP), you can access the many information sources on the World Wide Web. To connect to a Web site: 1 Connect to your Internet account. 2 Depending on the method you use to connect to your Internet account, you may need to start your Web browser. Click (Start), then click Internet.
MU0000000_eM_ENG_V09A3.book Page 14 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started Downloading files Caution To protect your computer against viruses, make sure that you scan the files you download. Downloading is the process of transferring files from a computer on the Internet to your computer. To download files or programs from a Web site: 1 Connect to your Internet account.
MU0000000_eM_ENG_V09A3.book Page 15 Wednesday, August 19, 2009 5:06 PM Ethernet networking Wired Ethernet networking An wired Ethernet network consists of two or more computers connected together through an Ethernet cable. This connection type is commonly used in offices around the world and can be used to build computer networks in the home. Ethernet, Fast Ethernet, or Gigabit Ethernet Important Check local code requirements before installing Ethernet cable or other wiring in your home or office.
MU0000000_eM_ENG_V09A3.book Page 16 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started Attached to the router are all of your computers or Ethernet-ready devices. Also connected to the router is a cable or DSL modem that provides access to the Internet.
MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page 18 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started Connecting network cables We recommend using category 5 (Cat 5), unshielded, twisted-pair cable (about 1/4-inch diameter with a thin outer-jacket, containing eight color-coded wires), and equipment compatible with this type of cable. This type of cable is equipped with RJ-45 connectors (like a large telephone jack connector, but with eight pins) on each end.
MU0000000_eM_ENG_V09A3.book Page 19 Wednesday, August 19, 2009 5:06 PM In addition to a router, you need a straight-through cable for each computer you want to connect to the network. Cable/DSL modem Router WAN port To set up a network using a router: 1 Plug one end of the power adapter into the AC connector on the router and the other end into a grounded, 110V electrical outlet. 2 Turn on your computers.
MU0000000_eM_ENG_V09A3.book Page 20 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started Establishing your Ethernet network connection Naming the computers and the workgroup Important You must give each computer on the network a unique Computer Name and the same Workgroup Name. Make sure that you have set up your router (wired network) or access point (wireless network). If you are setting up a wired network, make sure that you have connected the network cabling.
MU0000000_eM_ENG_V09A3.book Page 21 Wednesday, August 19, 2009 5:06 PM Adding a printer to your network Instead of plugging a printer into each of your computers, you can add a printer to your network. To add a printer to the network, do one of the following: • Connect your printer to your networked computer, then share the printer. For information about sharing printers, see “Sharing drives and printers” on page 21.
MU0000000_eM_ENG_V09A3.book Page 22 Wednesday, August 19, 2009 5:06 PM Chapter 2: Setting Up and Getting Started 2 Right-click the drive or folder that you want to share, then click Share. The Properties dialog box opens. If you share a drive, the entire contents of that drive will be available to everyone on your network. If you share a folder, only the contents of that folder will be available to everyone on the network. 3 Click the Sharing tab. Click Share.
Using the network After the drives and printers on each network computer are shared, you can: • View shared drives and folders • Map a network drive • Open and copy files stored on other network computers • Print documents on network printers Creating a shortcut to a network drive After a shortcut is created on a computer for a drive or folder on another computer, the contents of the drive or folder can be accessed as if the drive were attached directly to the computer.
Chapter 2: Setting Up and Getting Started Copying files across the network To copy files across the network: 1 Click (Start), then click Computer. The Computer window opens. 2 Browse to the network drive that contains the file you want to copy. 3 Browse to the file you want to copy. 4 Right-click the file, then click Copy. 5 Right-click the folder where you want to copy the file to, then click Paste.
25 MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page 26 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting First steps If you have problems with your computer, try these things first: • Make sure that the power cord is connected to your computer and an AC outlet and that the AC outlet is supplying power. • If you use a power strip or surge protector, make sure that it is turned on. • If a peripheral device (such as a keyboard or mouse) does not work, make sure that all connections are secure.
MU0000000_eM_ENG_V09A3.book Page 27 Wednesday, August 19, 2009 5:06 PM Add-in cards The computer does not recognize an add-in card • Shut down and restart your computer. • Make sure that you have installed the required software. For more information, see the documentation that came with your add-in card. Audio See “Sound” on page 43. CD or DVD drives See “Optical disc drives” on page 39. DVD drives • See “CD or DVD drives” on page 27.
MU0000000_eM_ENG_V09A3.book Page 28 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting • Make sure that all computers are using the same Subnet Mask. • If you assigned IP addresses to the computers, make sure that all computers have different IP addresses. For home networks, IP addresses should be 192.168.N.N where N is a number you assign between 0 and 254.
MU0000000_eM_ENG_V09A3.book Page 29 Wednesday, August 19, 2009 5:06 PM Expansion cards The computer does not recognize an expansion card • Shut down and restart your computer. • Make sure that you have installed the required software. For more information, see the documentation that came with your expansion card. File management Help For more information about restoring deleted files, click Start, then click Help and Support. Type System Restore in the Search box, then press ENTER.
MU0000000_eM_ENG_V09A3.book Page 30 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting • Empty the Recycle Bin by right-clicking the Recycle Bin icon, then clicking Empty Recycle Bin. Caution All deleted files will be lost when you empty the Recycle Bin. • Save your files to another drive. If the hard drive is full, copy any files not regularly used to backup media, then delete them from the hard drive.
MU0000000_eM_ENG_V09A3.book Page 31 Wednesday, August 19, 2009 5:06 PM You see a “Non-system disk” or “disk error” error message • Your hard drive may have become damaged. Internet See also “Modem (dial-up)” on page 34. You cannot connect to the Internet • If you are using a dial-up modem, make sure that the modem cable is plugged into the modem jack and not the Ethernet network jack. See your setup poster to make sure that the connections have been made correctly.
MU0000000_eM_ENG_V09A3.book Page 32 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting You see an “Unable to locate host” message and are unable to browse the Internet • This problem can occur when you have typed a URL (Web address) incorrectly, you have lost your Internet connection, or your ISP is having technical difficulties. • Double-check the URL or try a different URL.
MU0000000_eM_ENG_V09A3.book Page 33 Wednesday, August 19, 2009 5:06 PM Keyboard The keyboard does not work • Make sure that the keyboard cable is plugged in correctly. For more information, see the poster that came with your computer. • Remove all extension cables and switch boxes. • Clean the keyboard by using an aerosol can of air with a narrow, straw-like extension to remove dust and lint trapped under the keys. • Try a keyboard that you know works to make sure that the keyboard port works.
MU0000000_eM_ENG_V09A3.book Page 34 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting You see a “Not enough memory” error message • Close all programs, then restart your computer. Memory card reader Drive letters for the memory card slots do not appear in the My Computer window • Reboot your computer. Modem (cable or DSL) • See the documentation that came with your modem for additional troubleshooting information. Modem (dial-up) See also “Internet” on page 31.
MU0000000_eM_ENG_V09A3.book Page 35 Wednesday, August 19, 2009 5:06 PM Help For more information about dialing properties, click Start, then click Help and Support. Type dialing in the Search box, then press ENTER. • Disconnect any answering machine, fax • • machine, or printer that is on the same line as the modem. Do not connect these devices to the same telephone line as the modem. Make sure that you are not using a digital, rollover, or PBX line. These lines do not work with your modem.
MU0000000_eM_ENG_V09A3.book Page 36 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting • Try another telephone line (either a • different telephone number in your house or a telephone line at a different location). If you can connect on this line, call your telephone service. Try connecting with the modem at a lower connection speed. If reducing the connect speed lets you connect, call your telephone service. The telephone line may be too noisy.
MU0000000_eM_ENG_V09A3.book Page 37 Wednesday, August 19, 2009 5:06 PM The modem is not recognized by your computer • Make sure that the line connected to the modem is working and plugged into the appropriate port on your computer. See your setup poster to make sure that the connections have been made correctly. • If the modem shares the telephone line with another device, make sure that the telephone line is not in use (for example, someone is on the telephone, or another modem is in use).
MU0000000_eM_ENG_V09A3.book Page 38 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting • Make sure that the monitor cable is • • • connected to the video port on the back of your computer. Check the cable for bent or damaged pins. Reinstall the device driver. Connect a monitor that you know works to your computer. The color is not uniform • Make sure that the monitor warms up for at least 30 minutes before making a final judgment about color uniformity.
MU0000000_eM_ENG_V09A3.book Page 39 Wednesday, August 19, 2009 5:06 PM The mouse works erratically • If the mouse pointer begins moving erratically across the computer display or becomes difficult to control precisely, cleaning the mouse will likely improve its accuracy. • Clean the mouse by wiping the bottom with a clean, damp cloth. Make sure that the optical sensor is clean and free of debris. Networks You cannot connect to your company network Every network is unique.
MU0000000_eM_ENG_V09A3.book Page 40 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting • Make sure that the drive is configured • correctly by following the instructions in the drive documentation. Reinstall the device driver. An audio CD does not produce sound • Make sure that the disc label is facing up, then try again. • Some music CDs have copy protection software. You may not be able to play these CDs on your computer. • Make sure that the volume controls are turned up.
MU0000000_eM_ENG_V09A3.book Page 41 Wednesday, August 19, 2009 5:06 PM • DVDs and DVD drives contain regional codes that help control DVD title exports and help reduce illegal disc distribution. To be able to play a DVD, the disc’s regional code and your DVD drive’s regional code must match. The regional code on your DVD drive is determined by your computer’s delivery address. The regional code for the United States and Canada is 1. The regional code for Mexico is 4.
MU0000000_eM_ENG_V09A3.book Page 42 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting Printer The printer will not turn on • Make sure that the printer is online. Many printers have an online/offline button that you may need to press. • Make sure that the power cable is plugged into an AC power source. The printer is on but will not print • Check the cable between the printer and your computer. Make sure that it is connected to the correct port. • Make sure that the printer is online.
MU0000000_eM_ENG_V09A3.book Page 43 Wednesday, August 19, 2009 5:06 PM Help For more information about printer troubleshooting, click Start, then click Help and Support. Type printer troubleshooter in the Search box, then press ENTER. Sound You are not getting sound from the speakers • Make sure that the speakers are turned on. • Make sure that the volume controls are turned up. • Make sure that mute controls are turned off.
MU0000000_eM_ENG_V09A3.book Page 44 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting Recovering your system You can solve most computer problems by following the information in “Troubleshooting” on page 25 or in the technical support pages at www.emachines.com. Problem solving may also involve reinstalling some or all of the computer’s software (also called recovering or restoring your system). eMachines provides everything you need to recover your system under most conditions.
MU0000000_eM_ENG_V09A3.book Page 45 Wednesday, August 19, 2009 5:06 PM Creating recovery discs If your computer experiences problems that are not recoverable by other methods, you may need to reinstall the Windows operating system and factory-loaded software and drivers. To reinstall using discs, you must create the set of recovery discs beforehand. To create recovery discs: 1 Click (Start), All Programs, eMachines, then click eMachines Recovery Management. eMachines Recovery Management opens.
MU0000000_eM_ENG_V09A3.book Page 46 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting Recovering pre-installed software and drivers As a troubleshooting step, you may need to reinstall the software and device drivers that came pre-installed on your computer from the factory. You can recover using either your hard drive or the backup discs you have created.
MU0000000_eM_ENG_V09A3.book Page 47 Wednesday, August 19, 2009 5:06 PM Returning your system to its factory condition In case your computer experiences problems that are not recoverable by other methods, you may need to reinstall everything to return your system to its factory condition. You can reinstall using either your hard drive or the recovery discs you have created.
MU0000000_eM_ENG_V09A3.book Page 48 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting 4 Click OK. The recovery process begins by restarting your computer, then continues by copying files to your hard drive. This process may take a while, but a eMachines Recovery Management screen shows you its progress. When the recovery has finished, a dialog box prompts you to restart your computer. 5 Click OK. Your computer restarts. 6 Follow the on-screen prompts for first-time system setup.
MU0000000_eM_ENG_V09A3.book 4 Page 49 Wednesday, August 19, 2009 5:06 PM Insert the second recovery disc when prompted, then follow the on-screen prompts to complete the recovery. Telephone support Before calling Customer Care If you have a technical problem with your computer, follow these recommendations before contacting Customer Care: • Make sure that your computer is connected correctly to a grounded AC power outlet that is supplying power.
MU0000000_eM_ENG_V09A3.book Page 50 Wednesday, August 19, 2009 5:06 PM Chapter 3: Troubleshooting • See the troubleshooting section of this chapter. Warning To avoid bodily injury, do not attempt to troubleshoot your computer problem if: - Power cords or plugs are damaged - Liquid has been spilled into your computer - Your computer was dropped - The case was damaged Instead, unplug your computer and contact a qualified computer technician.
51 MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page 52 Wednesday, August 19, 2009 5:06 PM Appendix A: Regulations and safety notices Taking care of your computer Please read the important instructions listed in this section. Following these instructions will help you maximize the durability of your computer. Important tips • Do not expose the computer to direct sunlight. Do not place it near sources of heat, such as a radiator. • Do not expose the computer to temperatures below 0oC (32oF), or above 50oC (122oF).
MU0000000_eM_ENG_V09A3.book Page 53 Wednesday, August 19, 2009 5:06 PM To clean an optical mouse For users of an optical mouse, refer to the documentation that came with your mouse for maintenance instructions. To clean your monitor Make sure that you keep your screen clean. For cleaning instructions, refer to the documentation that came with your monitor.
MU0000000_eM_ENG_V09A3.book Page 54 Wednesday, August 19, 2009 5:06 PM Appendix A: Regulations and safety notices Regulations and safety notices FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MU0000000_eM_ENG_V09A3.book Page 55 Wednesday, August 19, 2009 5:06 PM Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. Remarque à l'intention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries Hereby, Acer, declares that this PC series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
MU0000000_eM_ENG_V09A3.book Page 56 Wednesday, August 19, 2009 5:06 PM Appendix A: Regulations and safety notices device. In order to operate within the limits for compliance with Telecom's specifications, the associated equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is not less than 5 seconds between the end of one call attempt and the beginning of another.
MU0000000_eM_ENG_V09A3.book Page 57 Wednesday, August 19, 2009 5:06 PM List of applicable countries EU member states as of July 2009 are: Belgium, Denmark, Germany, Greece, Spain, France, Ireland, Italy, Luxembourg, the Netherlands, Austria, Portugal, Finland, Sweden, United Kingdom, Estonia, Latvia, Lithuania, Poland, Hungary, Czech Republic, Slovak Republic, Slovenia, Cyprus and Malta, Bulgaria and Romania.
MU0000000_eM_ENG_V09A3.book Page 58 Wednesday, August 19, 2009 5:06 PM Appendix A: Regulations and safety notices Acer America Corporation 333 West San Carlos St., San Jose CA 95110, U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules.
MU0000000_eM_ENG_V09A3.book Page 59 Wednesday, August 19, 2009 5:06 PM Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih Taipei Hsien 221, Taiwan Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan Contact Person: Mr. Easy Lai, e-mail:easy_lai@acer.com.
MU0000000_eM_ENG_V09A3.book Page 60 Wednesday, August 19, 2009 5:06 PM Appendix A: Regulations and safety notices The standards listed below are applied to the product if built with WLAN module or wireless keyboard and mouse. R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard: • Article 3.1(a) Health and Safety -. EN60950-1 -. EN62311 • Article 3.1(b) EMC -. EN301 489-1 -. EN301 489-3 (Applicable to non-bluetooth wireless keyboard mouse set). -.
MU0000000_eM_ENG_V09A3.
MU0000000_eM_ENG_V09A3.book Page 62 Wednesday, August 19, 2009 5:06 PM Remark: All images are for reference purposes only. Actual configuration may vary.
