Thanks for purchasing the Tinyhawk II Race. Designed in California, assembled in China.
Tinyhawk II Race Disclaimer Please read the disclaimer carefully before using this product. By using this product, you hereby agree to this disclaimer and signify that you have read them carefully and completely. This product is not suitable for people under the age of 18. Adult supervision is highly recommended for kids under the age of 18. Our Tinyhawk II Race features open-source flight controller and Electronic Speed Controllers to meet the FPV enthusiasts' need to upgrade their quad.
Tinyhawk II Race Table of Contents Disclaimer................................................................................................................................. 1 Precautions...............................................................................................................................1 Support...................................................................................................................................... 1 Product specification.............................
Tinyhawk II Race Product specification Tinyhawk II Race Parameter Diagonal wheelbase (without paddles) 90mm Maximum size of the aircraft (without antenna, cable tie) 119*110*40(mm) Aircraft weight (without battery) 47.
Tinyhawk II Race Tinyhawk II Race Structure 2 emax-usa.
Tinyhawk II Race Tinyhawk II Race Propeller Direction and Mounting There are 2 spinning directions for Tinyhawk II Race propellers, Clockwise (CW) and Counter-Clockwise (CCW). When Buying a set of propellers, 2 CW and 2 CCW will be given. The blunt leading edge indicates the direction the propeller is suppose to rotate as compared to the sharp trailing edge. When mounting propellers please make sure the correct orientation shown in the diagram below.
Tinyhawk II Race Tinyhawk II Race VTX Settings NOTE: Under normal operating conditions, please use the Betaflight OSD function to change VTX (video transmitter) settings. Only use the VTX push button to unlock as allowed for under the FCC and HAM licensing requirements, see below. If using the VTX push button to change settings, please note that the settings will revert to the Betaflight OSD's settings once the drone is power-cycled. VTX Schematic and Button Diagram VTX Channel Settings with the Button 1.
Tinyhawk II Race (3) Press the button and hold for 2s again to exit frequency group band / channel / power option and return to the menu. 4. Band / Channel / Power parameter change After entering frequency group band / channel / power option, short click button to change the parameter. Notice: If you change to an illegal channel using SmartAudio, there will be no image transmitting from Tinyhawk II Race.
Tinyhawk II Race required to have a HAM radio license or prior consent from the FCC.By purchasing this equipment, the user is agreeing that they understand these responsibilities and will operate the equipment legally. Emax cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. Changing VTX setting via Betaflight OSD Tinyhawk II Race is equipped with SmartAudio and is already configured with stock settings.
Tinyhawk II Race Figure 5 Figure 6 7 emax-usa.
Tinyhawk II Race Tinyhawk II Race All-in-One Flight Controller Tinyhawk II Race’s main electronic board is shown above. This board contains a F4 flight controller with all 4 esc’s and an 8CH receiver. On-Board Receiver The receiver is integrated into the main flight controller board and is set up via betaflight. Number of Channels: 8CH Compatibility: Receiver mode is SPI RX default protocol is FrSky_D (D8).
Tinyhawk II Race It is possible to place the receiver into Bind Mode via the Betaflight configurator. In the CLI tab type in this command: bind_rx Hit enter and your receiver should be in bind mode. Follow steps 2-3 from above to complete the binding process. Emax Tinyhawk II Race Flight Controller (FC) This flight controller has a F4 MCU with a MPU6000 gyro. Tinyhawk II Race flight controller comes pre-programmed and properly tuned for optimal flight.
Tinyhawk II Race Restoring the Tinyhawk II Race default settings 1. 2. 3. 4. 5. Download the latest CLI Dump File from https://emax-usa.com/ Connect Tinyhawk II Race to Betaflight configurator and select the CLI tab Open the CLI Dump File in a text editor and copy all the text. Paste the settings into the command bar and press enter Tinyhawk II Race will reconnect to Betaflight when completed 10 emax-usa.
Tinyhawk II Race Flight Always use caution when flying and operate in an open and controllable area. Please learn the flight controls first before powering on the aircraft to fly. Radio Stick Controls The left stick controls throttle and yaw direction of Tinyhawk II Race. The right stick controls pitch and roll of the aircraft. Left Stick Diagram Right Stick Diagram Fly Tinyhawk II Race Start by powering on your Radio and Goggles.
Tinyhawk II Race Arming Arming refers to setting Tinyhawk II Race to a fly ready state. When Tinyhawk II Race is powered on first it will not spin up the propellers until it is armed. Arm the aircraft by first moving throttle to the bottom position. Then move the left switch of the radio to its 3rd position upwards. You will see the propellers spinning when Tinyhawk II Race is successfully armed. In the event of a crash always disarm immediately.
Tinyhawk II Race Thank you for purchasing our product! Enjoy Flying Tinyhawk II Race. Warning： Please pay attention to your surroundings. Not recommended for persons under 18 years of age. 13 emax-usa.
