Installation Guide

ManualsBrandsEmberglow ManualsKitchenCountry Split Oak 24 in. Vented Natural Gas Fireplace Logs

INSTALLATION & OPERATION MANUAL

GAS FIREPLACE LOG

TIERED DUAL BURNER LOG SET

Complies with ANSI Z21-84

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

— Do not store or use gasoline or other ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

r’s phone. Follow the gas

supplier’s instructions.

r, call the re department.

— Installation and service must be performed by a quali ed installer, service

agency or the gas supplier.

WARNING: If the information in this manual is not followed exactly, a re or

explosion may result causing property damage, personal injury or loss of life.

Listed By

OMNI-Test Laboratores, Inc.

Portland

Oregon USA

SHM INTERNATIONAL 2012

Burner set for use with all styles and sizes of SureHeat Dual Burner Natural Gas Log Sets.

Models: BRO18NG, BRO24NG - CSO24NG, CSO30NG

MO18DBNG, MO24DBNG - SH18NG, SH24NG

DECORATIVE VENTED

Summary of content (16 pages)

PAGE 1
INSTALLATIO N & OPERATION MANUAL DECORATIVE VENTED GAS FIREPLACE LOG TIERED DUAL BURNER LOG SET Models: BRO18NG, BRO24NG - CSO24NG, CSO30NG MO18DBNG, MO24DBNG - SH18NG, SH24NG Burner set for use with all styles and sizes of SureHeat Dual Burner Natural Gas Log Sets. WARNING: If the information in this manual is not followed exactly, a re or explosion may result causing property damage, personal injury or loss of life.
PAGE 2
DUAL BURNER PART LIST Figure 1 1-6 GRANULES (HEAVY WEIGHT BAG) GLOWING EMBERS (LIGHT WEIGHT BAG) 16 17 NUMBER OF LOGS ARE DETERMINED BY THE SIZE AND MODEL CHOSEN SETS RANGE FROM 4 TO 9 LOGS INS TALLATIO N & OP E RATION F IREP L ACE G AS L O G TIERED DUAL BURNER LOG SET M odels : BRO18 NG, BRO 24 NG - CSO2 4 NG , CSO 30 NG M O18 DBNG, M O2 4 DBNG - SH1 8NG, S H2 4 NG Burner set for use with all styles and sizes of SureHeat Dual Burner Natural Gas Log Sets.
PAGE 3
WARNING: Improper use or installation may cause Carbon Monoxide Poisoning. Carbon Monoxide, is an colorless and odorless gas, and is a by- product of combustion. Caution must be taken to insure the fireplace is properly vented when logs are in use To . avoid having potentially dangerous fumes enter the living area, be sure the chimney is drawing pro perly and has sufficient draft. WARNING: Do not burn wood, solid fuels, or other material in any fireplace fitted with a gas log set.
PAGE 4
D. Prefabricated fireplace: Refer to the manufactures fireplace instruction manual for specific information regarding the running of a gas line into that particular model. A typical installation involves the insertion of a 1/2 inch gas pipe through the gas line tube provided by the manufacturer from outside the fireplace. The Knockout on the inside of the fireplace is removed as the gas pipe is punched through the fireplace. (See Figure 3). E.
PAGE 5
CONNECTING GAS SUPPLY TO BURNER ASSEMBLY Natural Gas applications installed without a Safety Pilot Ki t. LP/NG Safety Pilot Kit availableat your local store. (If a Safety Pilot Kit is to be used, please refer to seperate instructions included with the kit.) A. Place burner pan assembly in the center of the fireplace. B. Attach 3/8” Flare X 1/2” NPT gas valve (Part #13) to the 1/2 inch gas supply stub already in fireplace.
PAGE 6
LOG PLACEMENT MODEL: BRO18NG 2 1 5 3 4 7 8 6 Log Identification Back Log Stand-Offs in place Place log (1) onto back left area of the grate, perpendicular to log (2) Place log (3) at the front right of the grate with the “burned” area to the flame Place “Y” shaped log (4) onto left of the grate ahead of raised area Place log (5) atop log (4), brace on left center grate finger Place log (6) atop logs (1) and (3) Place the two small logs (7) and (8) in front of the grate as shown 6
PAGE 7
LOG PLACEMENT MODEL: BRO24 8 9 7 3 6 4 1 2 Log Identification Back Log Stand-Offs in place Place log (1) onto back right area of the grate Place “Y” shaped log (2) onto left of the grate ahead of raised area Place log (3) onto back left area of the grate, perpendicular to log (1) Place log (4) at the front right of the grate with the “split” area to the flame Place log (5) on to log (2) and brace it on the grate finger left of center Place log (6) atop logs (5) and (4) as shown 7
PAGE 8
LOG PLACEMENT  MODEL: BRO24 Continued Place the two small logs (7) and (8) in front of the grate as shown
PAGE 9
LOG PLACEMENT MODEL: CSO24/CSO30 7 9 3 8 2 5 1 4 6 Log Identification Back Log Stand-Offs in place Place Right front log (1) onto front area of the grate Place left front log (2) onto front area of the grate Place back log (3) onto raised area of the grate Place Cross-Log (4) at the center left Place “Y” shaped Cross-Log (5) at right 9 Place Cross-Log (6) from front left to lay on log (5) as shown
PAGE 10
LOG PLACEMENT MODEL: CSO24/CSO30 Continued Place Cross-Log (7) at the center right Place Cross-Log (8) at the top center across logs (5) and (7) Place log (8) in front of the set, on the pireplace floor Make sure it is in front of the burner pan 10
PAGE 11
LOG PLACEMENT MODEL: MO24NG 5 6 4 3 2 1 Back Log Stand-Offs in place Log Identification Place Main Front Log (1) onto front area of the grate Place shorter back log (2) onto Back Log Stand-Offs Place Cross-Log (3) at the left side Place Cross-Log (4) at the center Place Cross-Log (5) at the right side Place Cross-Log (6) from the center to the right side 11
PAGE 12
LOG PLACEMENT MODEL: MO24NG Continued Place Cross-Log (7) atop the center Left (4) to the center right (5) logs
PAGE 13
LOG PLACEMENT MODEL: SH18NG 1 2 4 6 5 3 Log Identification Back Log Stand-Offs in place Place main front log (1) onto front area of the grate Place shorter back log (2) onto raised area of the grate Place Cross-Log (3) at the left side Place Cross-Log (4) at the right side Place Cross-Log (5) at the center Place Cross-Log (6) from the center to the right side 13
PAGE 14
LOG PLACEMENT MODEL: SH24NG Log Identification Back Log Stand-Offs in place Place main front log (1) onto front area of the grate Place shorter back log (2) onto raised area of the grate Place Cross-Log (3) at the left side Place Cross-Log (4) at the center left Place Cross-Log (5) at the center right Place Cross-Log (6) at the right side 14
PAGE 15
LOG PLACEMENT MODEL: SH24NG Continued Place cross-log (7) atop cross-log (6) and to front center as shown 15
PAGE 16
MAINTENANCE Very little maintenance is required. The carbon deposit resulting from combustion is natural and adds to the realistic appearance of the set. If carbon becomes excessive it can be lightly brushed or vacuumed away. TROUBLE SHOOTING 1. Problem No Ignition Cause -Valve not fully in “on” position -gas line obstruction 2.