Installation Guide

ManualsBrandsEmberglow ManualsKitchenLP/NG Safety Pilot Kit for Vented Log Sets

MODEL CVS303

Supplemental Installation Instructions for use with

Natural Gas Log Sets

NOTE: This kit is for both Natural Gas and LP Gas applications. For LP (Propane) Gas

installation, see additionall LP/Propane instructions packaged with necessary hardware.

DO NOT USE THE NATURAL GAS ORIFICE HOLDER SUPPLIED WITH THIS KIT

ON LP(PROPANE) GAS INSTALLATIONS! IMPROPER COMBUSTION WILL OCCUR!

IMPORTANT:

Read and follow ALL instructions carefully, as these supplemental Pilot Assembly instr-

uctions are to be used in conjunction with the General Installation Instructions supplied

with all Vented Natural Gas Log Sets.

National fuel gas code requirements mandate the use of a Safety Pilot Valve on all LP/

Propane applications. These regulations MUST be followed on all installations of this type.

Part

No.

Description

Part

No.

Part

No.

Description Description

Gas Control Valve

Thermocouple lead connection

Pilot Line Connection

Pilot Burner Assembly

Pilot Bracket

Sheet Metal Screw (2)

Machine Screw (2)

Nut (2)

Pilot Orifice Location (NG)

Heat Shield

Lock Nut (3/8 NPT)

Street Elbow, 90 deg. (2)

Natural Gas Orifice

Holder (No Orifice)

SAFETY PILOT KIT

Thread Sealant

Illustrated Parts List

Control Knob

Pilot supply line

3” Pipe Nipple

3/8 Female Pipe Elbow

LP Orifice Holder

LP Orifice 18” set (Small Hole)

LP Orifice 24” set (Large Hole)

You will need to purchase ACC 18

When converting to LP/Propane gas

Summary of content (6 pages)

PAGE 1
MODEL CVS303 SAFETY PILOT KIT Supplemental Installation Instructions for use with Natural Gas Log Sets NOTE: This kit is for both Natural Gas and LP Gas applications. For LP (Propane) Gas installation, see additionall LP/Propane instructions packaged with necessary hardware.
PAGE 2
INSTALLATION ON DUAL BURNER SYSTEMS WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects, or other reproductive harm. This Safety Pilot Kit contains a Control Valve certiﬁed by C.S.A., which provides a safe and convenient way to ignite your Energy Efﬁcient gas log set.
PAGE 3
INSTALLATION ON DUAL BURNER SYSTEMS cont. G. Using pipe sealant the 3” Nipple (Part #15) to the 3/8” Street Elbow attached to the valve assembly and to the 3/8" Female Elbow (Part #16). Connect the 3/8" Female elbow, which is now connected to the entire valve assembly to the Burner Oriﬁce. Using pipe sealant on threads. (See Figure 7) H. The valve assembly can be rotated to better conceal the controls. Simply rotate the entire valve assembly by turning the top 3/8" Street Elbow with a wrench.
PAGE 4
LIGHTING YOUR GAS LOGS WITH THE SAFETY PILOT KIT 1. Light Pilot Turn Control Knob to Pilot Position (Figure 6 ), push knob fully in and hold a long lighted match at the outlet of Pilot Burner Assembly. After lighting the Pilot, hold the Control Knob in the ignition position for approximately 45 seconds.
PAGE 5
TROUBLESHOOTING PROBLEM CAUSE CORRECTIVE ACTION 1. Pilot noise Excess pressure • Check line pressure and adjust to 7 inch water column. • Adjust pilot location away from flame. 2.
PAGE 6
LIMITED WARRANTY Limited Warranty shall apply to the original purchaser at the original installation point onl y. Pilot, valves and thermocouples are guaranteed for a period of one (1) year under the original manufacturers warranty. General Warranty: This warranty does not apply in the case of improper installation, neglect, accident, misuse or as a result of modiﬁcations of the original product. All costs for removal and re-installation are the expressed responsibility of the purchaser .