LPe11002 HBA Installation Manual
Copyright© 2005 Emulex Corporation. All rights reserved worldwide. No part of this document may be reproduced by any means nor translated to any electronic medium without the written consent of Emulex Corporation. Information furnished by Emulex Corporation is believed to be accurate and reliable. However, no responsibility is assumed by Emulex Corporation for its use; or for any infringements of patents or other rights of third parties which may result from its use.
Table of Contents Introduction................................................................................................................................................... 1 Major Features ................................................................................................................................ 1 Compatibility .................................................................................................................................... 2 Prerequisites........................
Introduction The Emulex® LPe11002 host bus adapter (HBA) is a dual-channel, 4.25 gigabit per second (Gb/s), Fibre Channel (FC) Peripheral Component Interconnect Express (PCIe) HBA. The core technology of this HBA is Emulex’s eighth generation FC controller. The controller incorporates a multifunction native PCIe core that is compliant to the PCIe Base Specification 1.0a and PCI Express CEM Specification 1.0a.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for products such as LP8000, LP9002L, LP9802, LP10000 HBAs • Comprehensive array of operating system (OS) drivers: • • Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX • OEM-specific drivers for AIX and some other operating sy
The host adapter has two six-post jumper blocks, one jumper block for each port, that control the host adapter's device ID. The ID is selected by installing a jumper between posts 1 and 2, or 3 and 4, or 5 and 6. If no jumper is installed, the default device ID is 1AE5. Port 0 is the top transceiver, and port 1 is the bottom transceiver.
3. Remove the computer case. Note: For best I/O performance, place the adapter into an empty PCIe x4 or higher slot. PCIe slots are shorter than standard PCI 64-bit slots. Do not attempt to plug the adapter into a standard PCI slot. 4. Remove the blank panel from an empty PCIe bus slot. Follow steps 5–8 to change the bracket if they are different sizes. Otherwise, skip to step 9. Note: The HBA comes with a standard PCI bracket installed. A low-profile bracket is included in the box with the HBA.
Attaching Media Note: The HBA will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product (that is, multimode to multimode.) Use multimode fiber optic cable, with short-wave lasers, that adheres to the following specifications: Table 3: Media Specifications Fiber Optic Cable Maximum Length Minimum Length Connector 62.5/125 µm (multimode) 200 MHz*km bandwidth cable 300 meters at 1.0625 Gb/s 150 meters at 2.125 Gb/s 70 meters at 4.
Applying Power To apply power: 1. Verify that the HBA is securely installed in the computer. 2. Verify that the correct media is attached. 3. Plug in and turn on the computer. 4. Observe LEDs for Power On Self Test (POST) results. Viewing the LEDs Green and yellow LEDs can be seen through openings in the HBA's mounting bracket.Green indicates firmware operation and yellow signifies port activity. Each port has a corresponding set of green and yellow LEDs.
Table 4: POST Conditions and Results (Continued) Yellow LED Green LED State Slow Blink Slow Blink Off-line for download Fast Blink Slow Blink Restricted off-line mode (Waiting for restart) Flashing Slow Blink Restricted off-line mode (Test active) LPe11002 Hardware Installation Manual Page 7
References Specifications Table 5: LPe11002 Specifications Parameter Range Media Interface The controller interfaces to the physical media through an FC-0 Media Interface (FC-PI compliant transceiver), and then connects through dual optical fiber LC connectors. Physical Dimensions Low-profile MD2 form factor, 6.600 inches by 2.536 inches, and accommodates both the full-height and low-profile bracket. Power Requirements In a PCIe x4 slot: • 5.9 watts (typical) @ +3.3 VDC • 8.5 watts (maximum) @ +3.
FCC and Regulatory Notices LPe11002 HBA Models This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Paul Folino, Chief Executive Officer Emulex Corporation (714) 662-5600 3333 Susan St. Costa Mesa, CA.
Notice for Taiwan and Translations (BSMI) Translation: This equipment is a Class A ITE, and operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. Notice for South Korea and Translations (MIC) Translation: Class A Equipment: Please note that this equipment has been approved for business purposes with regards to electromagnetic interference.
LPe11002 Hardware Installation Manual Page 11
Laser Safety Notice This laser safety information contains certification and product information covering laser products known as optical small form factor transceivers incorporated in Emulex LightPulse host adapters. The small form factor transceiver is the primary cable connection mechanism for any optical port on the host adapter. This data is not intended to be a replacement for any safety regulations and standards; relevant safety documents should always be consulted if necessary.
Alternatively, at the discretion of the manufacturer, the same statement may be included in user information. If a label is used, an example of the IEC Class 1 information label that is suitable for most European countries is shown below. The label consists of black printing on a white background. Languages represented on this label are English, German, Finnish and French, and they represent the minimum set for acceptance of a Class 1 product in most European countries.
factor transceiver, and the system level documentation and labeling. Copies of the certificate of conformity for any small form factor transceiver sold by Emulex can be obtained upon request from Emulex Corporation, Costa Mesa.
