Installation Guide

ManualsBrandsEMCO ManualsDoors & Windows32 in. x 80 in. 200 Series White Triple-Track Storm Door

for EMCO

Woodcore Triple-Track and

Colonial Triple-Track Storm Doors

Installation Guide

Please Do Not Return Product to Store!

EMCO Enterprises, Inc.

PO Box 853

Des Moines, IA 50306-0853

Rev 6-2011 11025

P/N 503571

with any questions regarding installation, mis-cut part replacement, lost part replacement, or anything else related to

your storm door purchase.

• If your abilities do not match the requirements of this installation, contact an experienced contractor.

• EMCO has no responsibility in regard to the post-manufactured assembly and installation of EMCO

products.

PLEASE call the storm door Solution Center at 1-800-933-3626

PARTS OVERVIEW

Rain Cap

Door Frame

Hinge Rail with 4 hinges

(Hinge Side Z-bar)

Ventilating Glass panel (2)

Insect Screen

Latch Rail

(Handle Side Z-bar)

Sweep, vinyl

Sweep, metal

Sweep Fin

Not Shown

Hardware Kit, includes

Door Mounting screws

Handle Set

Closer Kit

Your storm door should contain the

following parts:

Figure 1

EMCO Enterprises, Inc., is a wholly owned subsidiary of Andersen Corporation. EMCO manu-

factures and supports the limited warranties for Andersen® and EMCO® doors. “Andersen”,

“EMCO” and all other marks where denoted are trademarks of Andersen Corporation.

Summary of content (8 pages)

PAGE 1
Installation Guide for EMCO® Woodcore Triple-Track and Colonial Triple-Track Storm Doors Please Do Not Return Product to Store! PLEASE call the storm door Solution Center at 1-800-933-3626 with any questions regarding installation, mis-cut part replacement, lost part replacement, or anything else related to your storm door purchase. • If your abilities do not match the requirements of this installation, contact an experienced contractor.
PAGE 2
SAFETY FIRST - Please read and follow all warnings and cautions in this guide. warning Entry door hardware and handle may become hot when exposed to sunlight. Improper use of hand or power tools could result in injury and/or product damage. Follow equipment manufacturer’s instructions for safe operation. Always wear safety glasses. warning Windows and doors can be heavy.
PAGE 3
2. INSTALLATION PREPARATION In this step, you will remove the ventilating glass panels. . Lay the door flat on a protected surface with the exterior side down. TIP: Lay on door carton. Figure 5 2. Remove the lower ventilating glass panel by pulling the latches at the bottom toward each other. Lift the lower portion of the ventilating glass panel up and then rotate it to remove (Figure 5). 3. Repeat the previous step to remove the upper ventilating glass panel. 4.
PAGE 4
3. PREPARE STORM DOOR FOR HANGING 1 - #8x1” Tools needed: 8 - #8x1” 1/8” LEFT HINGE - Exterior View (Figure 9) 1 In this step, you will hang the rain cap against the top mounting surface (Figure 9). 1. Center the rain cap in the door opening. 2. Using a pencil, mark the hinge side hole on the mounting surface. Set rain cap aside. 3. Using the drill and 1/8” drill bit, drill a hole in the mounting surface. . Place the rain cap back on the door opening. 5.
PAGE 5
4. HANG HINGED STORM DOOR: 6 - #8x1” Tools needed: 8 - #8x1” 1/8” LEFT HINGE - Exterior Views In this step, you will hang the storm door in the opening. RIGHT HINGE - Exterior Views . Position the door in the opening so 1 3 2 Figure 14 Figure 15 that the edge of the hinge rail is flush with the end of the rain cap, and the top end of the hinge rail is butted up against the underside of the rain cap (Figure 14). 2.
PAGE 6
5. INSTALL REMAINING FRAME COMPONENTS: 8 - #8x1” Tools needed: 1/8” LEFT HINGE - Exterior Views In this step, you will finish fastening the rain cap to the top mounting surface. RIGHT HINGE - Exterior Views 1. Close the storm door. 2. Adjust the rain cap so that the 1 1 gap between the rain cap and door frame is the same along the entire length of the rain cap. 3. Using the 1/8” drill bit, drill holes in the mounting surface through the pre-drilled holes in the rain cap (Figure 17). 4.
PAGE 7
6. INSTALL WEATHER SEALING COMPONENTS Tools needed: OR 2 - #8x1/2” 4 - #8x1/2” 1/8” LEFT HINGE - Interior Views For doors with a Brass or Nickel finish sweep only: in this step, you will install the bottom sweep fin (Figure 21). 9 RIGHT HINGE - Interior Views 9 1. Slide the sweep fin into the fin track flush with the sweep end. 2. Use pliers to crimp the ends of the track legs (both ends) to secure the fin. 3. Trim off excess sweep fin material. 8 8 In this step, you will install the sweep.
PAGE 8
REGULAR MAINTENANCE WINDOW GLASS – The glass may be cleaned with any household glass cleaner. Keep glass cleaners away from painted parts and brass/nickel components. PLASTIC PARTS – Plastic door components may be cleaned using a mild soap and water mixture and by gently rubbing the affected area. Do not use harsh abrasives or any product that contains chlorine. ALUMINUM PARTS – Aluminum parts on the door may be cleaned using a mild soap and water mixture and by gently rubbing the affected area.