Two-Wire Toroidal Conductivity Transmitter Instruction Manual

ManualsBrandsEmerson ManualsSwitch5081-T

Model 5081-T

Two-Wire Toroidal Conductivity Transmitter

Instruction Manual

PN 51-5081T/rev.D

February 2006

Summary of content (98 pages)

PAGE 1
Instruction Manual PN 51-5081T/rev.
PAGE 2
ESSENTIAL INSTRUCTIONS READ THIS PAGE BEFORE PROCEEDING! Rosemount Analytical designs, manufactures, and tests its products to meet many national and international standards. Because these instruments are sophisticated technical products, you must properly install, use, and maintain them to ensure they continue to operate within their normal specifications.
PAGE 3
MODEL 5081-T TABLE OF CONTENTS MODEL 5081-T TWO-WIRE TRANSMITTER TABLE OF CONTENTS Section 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Title DESCRIPTION AND SPECIFICATIONS ................................................................ Features and Applications........................................................................................ Specifications ........................................................................................................... Hazardous Location Approval ...............
PAGE 4
MODEL 5081-T TABLE OF CONTENTS TABLE OF CONTENTS CONT’D 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 PROGRAMMING..................................................................................................... General .................................................................................................................... Output ...................................................................................................................... Temp ...............................................
PAGE 5
MODEL 5081-T TABLE OF CONTENTS LIST OF FIGURES Number 1-1 1-2 1-3 1-4 1-5 2-1 2-2 2-3 2-4 2-5 2-6 3-1 3-2 3-3 3-4 3-5 3-6 3-7 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 Title Transmitter Display During Calibration and Programming ....................................... Infrared Remote Controller....................................................................................... HART Communicator ................................................................
PAGE 6
MODEL 5081-T TABLE OF CONTENTS LIST OF FIGURES - CONT’D Number 5-1 5-2 5-3 5-4 5-5 6-1 6-2 8-1 9-1 9-2 9-3 10-1 10-2 10-3 10-4 10-5 11-1 Title Process Display Screen ........................................................................................... Program Display Screen .......................................................................................... Infrared Remote Controller.......................................................................................
PAGE 7
MODEL 5081-T SECTION 1.0 DESCRIPTION AND SPECIFICATIONS SECTION 1.0 DESCRIPTION AND SPECIFICATIONS • CHOICE OF COMMUNICATION PROTOCOL: HART or FOUNDATION Fieldbus. • LARGE, EASY-TO-READ two-line display shows the process measurement and temperature. • SIMPLE MENU STRUCTURE. • ROBUST NEMA 4X and NEMA 7B ENCLOSURE. • INTRINSICALLY SAFE DESIGN allows the transmitter to be used in hazardous environments (with appropriate safety barriers).
PAGE 8
MODEL 5081-T SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.2 SPECIFICATIONS 1.2.1 GENERAL SPECIFICATIONS Enclosure: Cast aluminum containing less than 6% magnesium, with epoxy polyester coating. NEMA 4X (IP65) and NEMA 7B. Neoprene O-ring cover seals. Dimensions: See drawing. Conduit Openings: ¾-in. FNPT Ambient Temperature: -4 to 149°F (-20 to 65°C) Storage Temperature: -22 to 176°F (-30 to 80°C) Relative Humidity: 0 to 95% (non-condensing) Weight/Shipping Weight: 10 lb/10 lb (4.5/5.
PAGE 9
MODEL 5081-T SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.2.3 TRANSMITTER SPECIFICATIONS @ 25°C Measured Range*: 50 to 2,000,000 µS/cm (see chart) Accuracy: ± 1.0% of reading Repeatability: ± 0.25% of reading Stability: 0.25% of output range/month, non-cumulative Ambient Temperature Coefficient: ± 0.2% of FS/°C Temperature Slope Adjustment: 0-5%/° C % Concentration Ranges: Sodium Hydroxide: 0 to 15% Hydrochloric Acid: 0 to 16% Sulfuric Acid: 0 to 25% and 96 to 99.7% 1.2.
PAGE 10
MODEL 5081-T 1.4 TRANSMITTER DISPLAY DURING CALIBRATION AND PROGRAMMING (FIGURE 1-1) 1. Continuous display of conductivity or resistivity readings. SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 8 1 F A U L T 7 H O L D 2. Units: µS/cm, mS/cm, ppm, or %. 3. Current menu section appears here. 6 4. Submenus, prompts, and diagnostic readings appear hear. #"c"" 2 mS/cm 3 CALIBRATE PROGRAM DIAGNOSE /-[5ES-U1 5. Commands available in each submenu or at each prompt appear here. 6.
PAGE 11
MODEL 5081-T SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.6 HART COMMUNICATIONS 1.6.1 OVERVIEW OF HART COMMUNICATION HART (highway addressable remote transducer) is a digital communication system in which two frequencies are superimposed on the 4 to 20 mA output signal from the transmitter. A 1200 Hz sine wave represents the digit 1, and a 2400 Hz sine wave represents the digit 0. Because the average value of a sine wave is zero, the digital signal adds no dc component to the analog signal.
PAGE 12
MODEL 5081-T SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.7 FOUNDATION FIELDBUS Figure 1-4 shows a 5081-T-FF being used to measure conductivity. The figure also shows three ways in which Fieldbus communication can be used to read process variables and configure the transmitter. FIGURE 1-4. CONFIGURING MODEL 5081-T TRANSMITTER WITH FOUNDATION FIELDBUS 1.
PAGE 13
MODEL 5081-T SECTION 1.0 DESCRIPTION AND SPECIFICATIONS FIGURE 1-5.
PAGE 14
MODEL 5081-T SECTION 2.0 INSTALLATION SECTION 2.0 INSTALLATION 2.1 2.2 2.3 2.4 2.5 Unpacking and Inspection Orienting the Display Board Mechanical Installation Power Supply/Current Loop — Model 5081-T-HT Power Supply Wiring for Model 5081-T-FF/FI 2.1 UNPACKING AND INSPECTION Inspect the shipping container. If it is damaged, contact the shipper immediately for instructions. Save the box. If there is no apparent damage, remove the transmitter. Be sure all items shown on the packing list are present.
PAGE 15
MODEL 5081-T SECTION 2.0 INSTALLATION 2.3.2 Mounting on a Flat Surface. See Figure 2-1. MILLIMETER INCH FIGURE 2-1.
PAGE 16
MODEL 5081-T SECTION 2.0 INSTALLATION 2.3.3 Pipe Mounting. See Figure 2-2. The pipe mounting kit (PN 2002577) accommodates 1-1/2 to 2 in. pipe. MILLIMETER INCH DWG. NO. 40308104 REV. G DWG. NO. 40308103 REV. C FIGURE 2-2.
PAGE 17
MODEL 5081-T SECTION 2.0 INSTALLATION 2.3.4 Inductive Loops. The Model 5081-T conductivity transmitter is designed to make accurate measurements while in contact with the process stream. Measurements can also be tailored to high temperature and/or high pressure streams. 2.3.5 Sensor Selection. All Rosemount Analytical contacting conductivity sensors with PT100 RTD or PT1000 RTD are compatible with the Model 5081-T transmitter.
PAGE 18
MODEL 5081-T 2.4 SECTION 2.0 INSTALLATION POWER SUPPLY/CURRENT LOOP — MODEL 5081-T-HT 2.4.1 Power Supply and Load Requirements. Refer to Figure 2-3. The minimum power supply voltage is 12.5 Vdc and the maximum is 42.4 Vdc. The top line on the graph gives the voltage required to maintain at least 12.5 Vdc at the transmitter terminals when the output signal is 22 mA. The lower line is the supply voltage required to maintain a 30 Vdc terminal voltage when the output signal is 22 mA.
PAGE 19
MODEL 5081-T 2.5 SECTION 2.0 INSTALLATION POWER SUPPLY WIRING FOR MODEL 5081-T-FF/FI 2.5.1 Power Supply Wiring. Refer to Figure 2-5 and Figure 2-6. Run the power/signal wiring through the opening nearest terminals 15 and 16. Use shielded cable and ground the shield at the power supply. To ground the transmitter, attach the shield to the grounding screw on the inside of the transmitter case. A third wire can also be used to connect the transmitter case to earth ground.
PAGE 20
MODEL 5081-T SECTION 3.0 WIRING SECTION 3.0 WIRING 3.1 3.2 Sensor Wiring Electrical Installation 3.1 SENSOR WIRING Wire sensor as shown below in Figure 3-1. Keep sensor wiring separate from power wiring. For best EMI/RFI protection, use shielded output signal cable in an earth-grounded metal conduit. Refer to the sensor instruction manual for more details. FIGURE 3-1. Wiring Model 5081T-HT 3.1.
PAGE 21
MODEL 5081-T SECTION 3.0 WIRING 3.1.2 POWER WIRING MODEL 5081-T-HT For general purpose areas, wire power as shown in Figure 3-2. For hazardous areas, please see hazardous area installation drawings. FIGURE 3-2. Power Supply/Current Loop Wiring for Model 5081-T-HT 3.1.3 POWER WIRING MODEL 5081-T-FF For general purpose areas, wire power as shown in Figure 3-3. For hazardous areas, please see hazardous area installation drawings. 9 - 32 FIGURE 3-3.
PAGE 22
MODEL 5081-T SECTION 3.0 WIRING 3.2 ELECTRICAL INSTALLATION All Rosemount Analytical contacting conductivity sensors with PT100 RTD or PT1000 RTD are compatible with the Model 5081-T transmitter. Please refer to Figures 3-5 thru 3-7 for appropriate sensor to transmitter wiring. The sensor cable should be routed through the left inlet closest to the connector.
PAGE 23
MODEL 5081-T SECTION 3.0 WIRING FIGURE 3-6.
PAGE 24
MODEL 5081-T SECTION 3.0 WIRING FIGURE 3-7.
PAGE 25
MODEL 5081-T SECTION 4.0 INTRINSICALLY SAFE & EXPLOSION PROOF SECTION 4.
PAGE 26
MODEL 5081-T SECTION 4.0 INTRINSICALLY SAFE & EXPLOSION PROOF FIGURE 4-3. FM Explosion-Proof Installation for Model 5081-T-HT 4.
PAGE 27
FIGURE 4-4. FM Intrinsically Safe Installation for Model 5081-T-HT MODEL 5081-T SECTION 4.
PAGE 28
FIGURE 4-5. CSA Intrinsically Safe Installation for Model 5081-T-HT MODEL 5081-T 22 SECTION 4.
PAGE 29
SECTION 4.0 INTRINSICALLY SAFE & EXPLOSION PROOF FIGURE 4-6.
PAGE 30
SECTION 4.0 INTRINSICALLY SAFE & EXPLOSION PROOF FIGURE 4-7.
PAGE 31
MODEL 5081-T SECTION 4.0 INTRINSICALLY SAFE & EXPLOSION PROOF FIGURE 4-8. FM Explosion-Proof Installation for Model 5081-T-FF 4.
PAGE 32
FIGURE 4-9. FM Intrinsically Safe Installation for Model 5081-T-FF MODEL 5081-T 26 SECTION 4.
PAGE 33
FIGURE 4-10. CSA Intrinsically Safe Installation for Model 5081-T-FF MODEL 5081-T SECTION 4.
PAGE 34
SECTION 4.0 INTRINSICALLY SAFE & EXPLOSION PROOF FIGURE 4-11.
PAGE 35
FIGURE 4-12. ATEX Intrinsically Safe Installation for Model 5081-T-FF MODEL 5081-T SECTION 4.
PAGE 36
USE ONLY APPROVED CONDUIT SEALS AND FITTINGS. TOROIDAL SENSOR RIGID METAL CONDUIT AND APPROVED SEALS 8 NOTES: UNLESS OTHERWISE SPECIFIED 1. INSTALLATION MUST CONFORM TO THE NEC. 7 2. SEAL REQUIRED AT EACH CONDUIT ENTRANCE. 3 3 70 5081-T-FI-67 °C DRV 10 COM F OR WIRING LABEL BE RA T E D 3 11 DR V 5 CLASS I, DIV 1, GPS B-D CLASS II, DIV 1, GPS E-G CLASS III, DIV 1 70°C MAX HAZARDOUS AREA 4 RELEASE DATE 5-6-04 RIGID METAL CONDUIT AND APPROVED SEALS 4 ECO NO.
PAGE 37
R APPROVED NO CHANGE WITHOUT FM APPROVAL. MATERIAL: AISI 300 SERIES STAINLESS STEEL .015+/-.005 THICK. MATERIAL TO BE ANNEALED & PASSIVATED. MAXIMUM HARDNESS BRINELL 190. 2. 1 NOTES: UNLESS OTHERWISE SPECIFIED ARTWORK IS SHEET 2 OF 2. 3. 1.30 ±.02 4 .XXX .XX FINISH ANGLES TOLERANCES + 1/2 - 4 1 DIMENSIONS ARE IN INCHES REMOVE BURRS & SHARP EDGES .020 MAX MACHINED FILLET RADII .020 MAX NOMINAL SURFACE FINISH 125 + .030 +- .
PAGE 38
A B 4 5 6 (La/Ra OR Lo/Ro) 7 8 NOTES: UNLESS OTHERWISE SPECIFIED 7 5 3 TABLE I B 17.5 IIC/ A,B,C,D,E,F,G 5081-T-FI 4 REV 17.5 360 380 Imax (mA) FINISH ANGLES TOLERANCES + 1/2 DIMENSIONS ARE IN INCHES 3 REMOVE BURRS & SHARP EDGES .020 MAX MACHINED FILLET RADII .020 MAX NOMINAL SURFACE FINISH 125 + .030 + .010 - MATERIAL .XXX .XX UNLESS OTHERWISE SPECIFIED Vmax (Vdc) IIB/ C,D,E,F,G ECO NO. ANY FM APPROVED ASSOCIATED APPARATUS 1 BY DATE J.
PAGE 39
SA R LR34186 ENCLOSURE 4 MATERIAL: AISI 300 SERIES STAINLESS STEEL .015+/-.005 THICK. MATERIAL TO BE ANNEALED & PASSIVATED. MAXIMUM HARDNESS BRINELL 190. 1 NOTES: UNLESS OTHERWISE SPECIFIED NO CHANGE WITHOUT CSA APPROVAL. 1.30 2. .125 9241516-01/A ±.02 .650 ±.015 4 FINISH ANGLES TOLERANCES + 1/2 - 4 1 DIMENSIONS ARE IN INCHES REMOVE BURRS & SHARP EDGES .020 MAX MACHINED FILLET RADII .020 MAX NOMINAL SURFACE FINISH 125 + .030 +- .010 MATERIAL .XXX .
PAGE 40
A B 11 5 4 8 NOTES: UNLESS OTHERWISE SPECIFIED 7 9 7 8 6 5 4 RELEASE DATE 5-6-04 ECO 2 REVISION DESCRIPTION ECO NO. REV A 380 Imax (mA) FINISH + 1/2 DIMENSIONS ARE IN INCHES ANGLES TOLERANCES 3 REMOVE BURRS & SHARP EDGES .020 MAX MACHINED FILLET RADII .020 MAX NOMINAL SURFACE FINISH 125 + .030 + .010 - MATERIAL .XXX .XX UNLESS OTHERWISE SPECIFIED Vmax (Vdc) 17.5 TABLE I PART NO. J. FLOCK THIS DWG CREATED IN SOLID EDGE PROJECT ENGR APVD CHECKED J. FLOCK B.
PAGE 41
1180 NO CHANGE WITHOUT BASEEFA APPROVAL. MATERIAL: AISI 300 SERIES STAINLESS STEEL .015+/-.005 THICK. MATERIAL TO BE ANNEALED & PASSIVATED. MAXIMUM HARDNESS BRINELL 190. 2. 1 NOTES: UNLESS OTHERWISE SPECIFIED 4 .XXX .XX FINISH ANGLES TOLERANCES + 1/2 - 4 1 DIMENSIONS ARE IN INCHES REMOVE BURRS & SHARP EDGES .020 MAX MACHINED FILLET RADII .020 MAX NOMINAL SURFACE FINISH 125 + .030 +- .010 LTR ECO PART NO 5/6/04 PROJECT ENGR APVD J.
PAGE 42
A B MAXIMUM SENSOR CABLE LENGTH IS 250 FEET. INFRARED REMOTE CONTROL UNIT (RMT PN 23572-00) FOR USE IN ZONE 0 CONDUCTIVITY SENSORS 222,225,226 & 228. 242 (1" & 2" ONLY) 9 MODEL 5081-T-FI XMTR 8 NOTES: UNLESS OTHERWISE SPECIFIED 7 5 5 12 11 9 6 7 5 4 RELEASE DATE 5-6-04 ECO NO. 8925 Baseefa Certified Product No modifications permitted without the approval of the Authorized Person Related Drawing 5081-T-FI MODEL NO.
PAGE 43
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION SECTION 5.0 DISPLAY AND OPERATION 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 Displays Infrared Remote Controller (IRC) - Key Functions Quick Start for Model 5081-T-HT Quick Start for Model 5081-T-FF Menu Trees Diagnostic Messages Default Settings Security Using Hold 5.1 DISPLAYS Figure 5-1 shows the process display screen, and Figure 5-2 shows the program display screen. Conductivity value #"c"" mS/cm Temperature in °C or °F FIGURE 5-1.
PAGE 44
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION 5.2 INFRARED REMOTE CONTROLLER (IRC) - KEY FUNCTIONS The infrared remote controller is used to calibrate and program the transmitter and to read diagnostic messages. See Figure 5-3 for a description of the function of the keys. RESET - Press to end the current operation and return to the process display. Changes will NOT be saved. RESET does not return the transmitter to factory default settings.
PAGE 45
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION 5.3 QUICK START FOR MODEL 5081-T-HT (HART) 1. On the Remote, press PROG, NEXT, NEXT, ENTER. 2. Use the arrow buttons to select COnduc (conductivity), nAOH (Sodium Hydroxide 0-15%), HCL (Hydrochloric Acid 0-16%), H2SO4L (Sulfuric Acid 0-30%), H2SO4H (Sulfuric Acid 96-99.7%), or CuSt (custom curve) mode. Press ENTER. If you chose CuSt, continue with step 3. If you chose COnduc or one of the preprogrammed % concentration modes, skip step 3 and go to step 4. 3.
PAGE 46
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION 5.4 QUICK START FOR MODEL 5081-T-FF/FI (FOUNDATION FIELDBUS) 1. On the Remote, press PROG, NEXT, ENTER. 2. Use the arrow buttons to select COnduc (conductivity), nAOH (Sodium Hydroxide 0-15%), HCL (Hydrochloric Acid 016%), H2SO4L (Sulfuric Acid 0-30%), H2SO4H (Sulfuric Acid 95-99.99%), or CuSt (custom curve) mode. Press ENTER. If you chose CuSt, continue with step 3.
PAGE 47
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION 5.5 MENU TREE - Conductivity The Model 5081-T transmitter has three menus: CALIBRATE, PROGRAM, and DIAGNOSE. Under the Calibrate and Program menus are several sub-menus. Figure 5-4 shows the complete menu tree for Model 5081-T-HT. Figure 5-5 shows the complete menu tree for Model 5081-T-FF. Model 5081T-HT Process Display Screen FIGURE 5-4. Menu Tree /-[5ES-U1 <1P<9S!" '""" U17:!-G6 CALIBRATION µS/cm 25.0C 12.
PAGE 48
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION FIGURE 5-5. Menu Tree Model 5081T-FF Process Display Screen /-[5ES-U1 <1P<9S!" '""" CALIBRATION µS/cm 25.0C 12.
PAGE 49
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION 5.6 DIAGNOSTIC MESSAGES Whenever a warning or fault limit has been exceeded, the transmitter displays diagnostic messages to aid in troubleshooting. Diagnostic messages appear in the same area as the temperature/output readings in the process display screen (see Figure 5-2). The display alternates between the regular display and the diagnostic message. Figure 5-4 shows the diagnostic fault messages for conductivity for Model 5081-T-HT.
PAGE 50
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION TABLE 5-2. Default Settings for Model 5081-T-HT VARIABLE NAME MNEMONIC FACTORY SETTINGS CUSTOMER SETTINGS Output 9VURVU – ___________ 4 mA &!O- 0 µS ___________ 20 mA $"!O- 20 mS ___________ Hold KQNG 21 mA ___________ Fault IDVNU 22 mA ___________ Dampening GRP 0 samples/second ___________ Test UHTU 04.00 mA ___________ Temperature UHOR Auto temperature compensation UDVUQ on ___________ Manual temperature UODP 25.
PAGE 51
MODEL 5081-T SECTION 5.0 DISPLAY AND OPERATION 5.8 SECURITY 5.8.1 General. Use the programmable security code to protect program and calibration settings from accidentally being changed. The transmitter is shipped with the security feature disabled. 5.8.2 Entering the Security Code. PROGRAM 5G EXIT """ ENTER 1. If calibration and program settings are protected with a security code, pressing PROG or CAL on the infrared remote controller causes the Id screen to appear. 2.
PAGE 52
MODEL 5081-T SECTION 6.0 START-UP AND CALIBRATION SECTION 6.0 START-UP AND CALIBRATION 6.1 ACCESSING THE CALIBRATE MENU The “Calibrate” menu is used to calibrate the transmitter to known temperature and conductivity values. This menu also contains the temperature calibration operation to establish the temperature slope. Figure 6-1 illustrates the relationship between the Calibrate Menu and its sub-menus. Each sub-menu leads to a series of prompts that are used for calibration.
PAGE 53
MODEL 5081-T 6.2 CALIBRATE MENU To access the “Calibrate” menu, press the CAL key on the Infrared Remote Control. If security has been enabled, the secondary process display will be replaced with a prompt asking for the “Id”. Using the IRC editing keys, enter the “Id”. If the correct “Id” is entered, the CALibrAtE sub-menu will appear when ENTER is pressed. SECTION 6.
PAGE 54
MODEL 5081-T SECTION 6.0 START-UP AND CALIBRATION 6.2.5 Temp Slope 1. Press NEXT to enter the tEMP SLOPE menu. The correct temperature slope must be entered into the transmitter to ensure an acceptable process variable measurement under fluctuating process temperature conditions. Enter the slope in measured conductivity units per degree temperature change using the IRC’s arrow keys. Press ENTER to enter the slope into memory; then press EXIT to return to the main screen. 2.
PAGE 55
MODEL 5081-T SECTION 6.0 START-UP AND CALIBRATION TABLE 6-1.
PAGE 56
MODEL 5081-T SECTION 7.0 PROGRAMMING SECTION 7.0 PROGRAMING 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 General Output Temp Display HART Setup Cust Range Default 7.1 GENERAL This section describes how to do the following: 1. assign values to the 4 and 20 mA outputs (for 5081-T-HT only) 2. set the current generated by the transmitter during hold (for 5081-T-HT only) 3. set the current generated by the transmitter when a fault is detected (for 5081-T-HT only) 4. enable and disable automatic temperature correction 5.
PAGE 57
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.2 OUTPUT (5081-HT only) 7.2.1 Purpose This section describes how to do the following: 1. assign values to the 4 and 20 mA outputs 2. set the output current generated during hold 3. set the output current generated when a fault is detected 4. control the amount of dampening on the output signal 5. generate a test current. 7.2.2 Definitions 1. CURRENT OUTPUTS.
PAGE 58
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.2.3 Procedure PROGRAM 9VU:VU EXIT 1. Press PROG on the remote controller. The OutPut submenu appears. NEXT ENTER PROGRAM &7- ""c"" EXIT ENTER 2. Press ENTER. The screen displays the 4 MA prompt. Use the arrow keys to change the setting. Press ENTER to save. PROGRAM $"7- #"c"" EXIT ENTER 3. The screen displays the 20 MA prompt. Use the arrow keys to change the setting. Press ENTER to save. PROGRAM 4Q[G $#c"" EXIT ENTER 4.
PAGE 59
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.3 TEMP 7.3.1 Purpose This section describes how to do the following: 1. Enable and disable automatic temperature compensation 2. Set a manual temperature compensation value for conductivity measurements 3. Tell the transmitter the type of temperature element in the sensor 7.3.2 Definitions 1. AUTOMATIC TEMPERATURE COMPENSATION. Conductivity measurements are directly affected by temperature.
PAGE 60
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.4 DISPLAY 7.4.1 Purpose This section describes how to do the following: 1. Configure the transmitter to measure conductivity, resistivity, or set up a custom curve 2. Set the temperature units to °C or °F 3. Set the output to current or percent of full scale 4. Enter a security code. 7.4.2 Definitions 1. MEASUREMENT.
PAGE 61
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.5 HART In multi-drop operation, polling addresses can be more conveniently set and debugging more conveniently performed using the infrared remote controller. PROGRAM 1. Press PROG on the infrared remote controller. 4-SU EXIT NEXT -GGSHTT EXIT "" NEXT :SH-7E EXIT 5G EXIT ENTER 2. Press NEXT until the screen at left appears. Press ENTER. 3. The HART menu tree is shown at left. Use the arrow keys to change settings. Press ENTER to store.
PAGE 62
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.6 SETUP CUST U!! SHI!! ! $'c" The Model 5081-T contains a curve fitting program that can create a second order curve for 3 to 5 user supplied data points. If only two points are entered, a straight line will be used. These points are from numerical data previously collected that is entered via the keypad. All data point must be approximately the same reference temperature.
PAGE 63
MODEL 5081-T SECTION 7.0 PROGRAMMING 7.7 RANGE 7.7.1 Purpose This section provides the steps to select automatic ranging or a specific fixed range of measurement. Five specific conductance ranges are selectable. Setting the Model 5081 to a fixed range reduces response time.
PAGE 64
MODEL 5081-T SECTION 8.0 FOUNDATION FIELDBUS OPERATION SECTION 8.0 FOUNDATION FIELDBUS OPERATION This section covers basic transmitter operation and software functionality. For detailed descriptions of the function blocks common to all Fieldbus devices, refer to Fisher-Rosemount Fieldbus FOUNDATION Function Blocks manual, publication number 00809-001-4783.
PAGE 65
MODEL 5081-T SECTION 9.0 OPERATION WITH MODEL 375 SECTION 9.0 OPERATION WITH MODEL 375 9.1 Note on Model 375 or 275 Communicator The Model 375 or 275 Communicator is a product of Emerson Process Management, Rosemount Inc. This section contains selected information on using the Model 375 or 275 with the Rosemount Analytical Model 5081-T-HT Transmitter. For complete information on the Model 375 or 275 Communicator, see the Model 375 or 275 instruction manual.
PAGE 66
MODEL 5081-T SECTION 9.0 OPERATION WITH MODEL 375 9.3 Operation 9.3.1 Off-line and On-line Operation The Model 375 Communicator features off-line and on-line communications. On-line means the communicator is connected to the transmitter in the usual fashion. While the communicator is on line, the operator can view measurement data, change program settings, and read diagnostic messages. Off-line means the communicator is not connected to the transmitter.
PAGE 67
MODEL 5081-T SECTION 9.
PAGE 68
MODEL 5081-T SECTION 9.0 OPERATION WITH MODEL 375 Basic setup (continued) Device information Distributor Model Dev id Tag Date Physicl signl code Write protect Snsr text Descriptor Message Revision #'s Universal rev Fld dev rev Software rev Hardware rev Detailed setup Sensors Main sensor PV Type [Conductivity, Resistivity, 0-12% NaOH, 0-15% HCl, 0-25% H2SO4, 96-99.
PAGE 69
MODEL 5081-T SECTION 9.
PAGE 70
MODEL 5081-T SECTION 9.0 OPERATION WITH MODEL 375 Local Display AO LOI units [mA, %] Xmtr ID Load Default Conf. Review PV PV AO PV LRV PV URV -------------------------------------------------------------------------------Notes: * Can be Cond, Res, NaOH, HCl, H2SO4, or Custom ** Valid only when PV Type = NaOH, HCl, 0-25% H2SO4, or Custom *** Valid only when Temp comp type = Linear **** Valid only when PV Type = Custom *. Valid only when PV Sensor Type = Toroidal *..
PAGE 71
MODEL 5081-T SECTION 9.
PAGE 72
MODEL 5081-T SECTION 9.
PAGE 73
MODEL 5081-T SECTION 9.
PAGE 74
MODEL 5081-T SECTION 9.
PAGE 75
MODEL 5081-T SECTION 9.
PAGE 76
MODEL 5081-T SECTION 9.
PAGE 77
MODEL 5081-T SECTION 9.
PAGE 78
MODEL 5081-T SECTION 9.
PAGE 79
MODEL 5081-T SECTION 9.
PAGE 80
MODEL 5081-T SECTION 9.
PAGE 81
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.1 OVERVIEW The Model 5081-T transmitters automatically monitor for fault conditions. The Diagnose Menu allows the current variable settings to be reviewed and shows fault messages indicating problems detected. Figure 10-1 illustrates the relationship between the Diagnose Menu and its sub-menus. The mnemonics are defined in Table 10-1. Step 3 10.1.
PAGE 82
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING TABLE 10-1.
PAGE 83
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.2 FAULT CONDITIONS Three classes of error conditions/problems are detected and differentiated between by the diagnostic program. System disabling problems are faults caused by failures in the loop or significant variations in the process. System non-disabling problems are warnings and deal with input or A to D conversion settings. The third class of detected problems are error messages and occur when the calibration limits are exceeded. 10.2.
PAGE 84
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.3 DIAGNOSTIC MESSAGES The Model 5081-T transmitter’s diagnostics constantly monitor the conductivity loop for possible problems. If an operational problem is encountered, check the display for a fault or error message. These are displayed in the Temperature/Current output segment of the display. Note the message and refer to Table 10-2 for a description of possible problems that may have triggered the diagnostic message. TABLE 10-2.
PAGE 85
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.4 QUICK TROUBLESHOOTING GUIDE Table 10-3 identifies some of the more common symptoms and suggests actions to help resolve a problem. In general, wiring is the most common cause. TABLE 10-3. Quick Troubleshooting Guide. SYMPTOM Wrong temperature reading. Suspected temp. compensation problem. ACTION Display segments missing. Display inoperable. Analyzer locks up; won't respond. Perform a temperature standardization. Verify sensor's RTD.
PAGE 86
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.5 SYSTEMATIC TROUBLESHOOTING If the Quick Troubleshooting Guide does not resolve the error, try the step-by-step approach offered in Figure 10-4. Step 1 Follow the troubleshooting flow chart. Step 2 Refer to the tests and instructions indicated by the flow chart to diagnose the problem. NOTE: Before starting this procedure make sure that all wiring is correct.
PAGE 87
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING Table 10-4. RTD Resistance Values. 10.6 RTD RESISTANCE VALUES Table 10-4 is a ready reference of RTD resistance values at various temperatures. These are used for test and evaluation of the sensor. Temperature Pt-100 Pt-1000 (°C) Resistance (ohms) Resistance (ohms) 0 100.00 1000 10 103.90 1039 20 107.79 1078 25 109.62 1096 30 111.67 1117 40 115.54 1155 50 119.40 1194 60 123.24 1232 70 127.07 1271 80 130.89 1309 90 134.70 1347 100 138.
PAGE 88
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.7 WARNING AND FAULT MESSAGES The Model 5081-T transmitter continuously monitors the sensor and transmitter for conditions that cause erroneous measurements. When a problem occurs, the transmitter displays either a warning or fault message. A warning alerts the user that a potentially disabling condition exists. There is a high probability that the measurement is in error. A fault alerts the user that a disabling condition exists.
PAGE 89
MODEL 5081-T 10.8 SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING TROUBLESHOOTING WHEN A FAULT OR WARNING MESSAGE IS SHOWING Message Explanation See Section OuEr rAnGE Over range, measurement exceeds display limit 10.8.1 SEnSor FAIL Bad sensor, sensor current is a large negative number 10.8.2 CAL Error Calibration error, sensitivity (nA/ppm) is too high or too low 10.8.3 nEEd 0 CAL Sensor needs re-zeroing, reading is too negative 10.8.4 rtd FAIL Bad temperature reading 10.8.
PAGE 90
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.8.3 CAL Error At the end of the calibration step, the transmitter calculates the sensitivity in nA/ppm. If the sensitivity is outside the range normally expected, the transmitter displays the CAL Error message and the transmitter does not update the calibration. For assistance, refer to the troubleshooting section specific for the sensor. 10.8.4 nEEd 0 CAL nEEd 0 CAL means that the concentration of the analyte is too negative. 1.
PAGE 91
MODEL 5081-T SECTION 10.0 DIAGNOSIS AND TROUBLESHOOTING 10.8.7 OFFSEt Err The OFFSEt Err message appears if the zero offset (in mV) exceeds the programmed limit. Before increasing the limit to make the OFFSEt Err message disappear, check the following: 1. Verify that the reference meter is working properly and is properly calibrated. 2. Verify that the process sensor is working. Check its response in a solution of known conductivity. 3.
PAGE 92
MODEL 5081-T SECTION 11.0 MAINTENANCE SECTION 11.0 MAINTENANCE 11.1 OVERVIEW 11.3 TRANSMITTER MAINTENANCE Maintenance consists of "Preventative" and "Corrective" measures. Periodically clean the transmitter window with household ammonia or glass cleaner. The detector for the infrared remote controller is located behind the window at the top of the transmitter face. The window in front of the detector must be kept clean. 11.2 PREVENTATIVE MAINTENANCE 11.2.1 Transmitter Maintenance.
PAGE 93
MODEL 5081-T SECTION 11.0 MAINTENANCE FIGURE 11-2. Exploded View of Model 5081-T Transmitter Three screws (part 13 in the drawing) hold the three circuit boards in place. Removing the screws allows the display board (part 2) and the CPU board (part 3) to be easily removed. A ribbon cable connects the boards. The cable plugs into the CPU board and is permanently attached to the display board. A 16 pin and socket connector holds the CPU and analog (part 4) boards together.
PAGE 94
MODEL 5081-T SECTION 12.0 THEORY OF OPERATION SECTION 12.0 THEORY OF OPERATION 12.1 OVERVIEW 12.4 OUTPUT LOGIC This section is a general description of how the Model 5081-T Transmitter operates. This section is for those users who desire a greater understanding of the transmitter’s operation. Normal transmitter operation specifies that the output tracks the process. However, the transmitter can be put into other modes of operation. 12.
PAGE 95
MODEL 5081-T SECTION 13.0 RETURN OF MATERIAL SECTION 13.0 RETURN OF MATERIAL 13.1 GENERAL. 13.1 NON-WARRANTY REPAIR. To expedite the repair and return of instruments, proper communication between the customer and the factory is important. Call 1-949-757-8500 for a R e t u r n Materials Authorization (RMA) number. The following is the procedure for returning for repair instruments that are no longer under warranty: 1. Call Rosemount Analytical for authorization. 2.
PAGE 96
This page intentionally left blank.
PAGE 97
WARRANTY Goods and part(s) (excluding consumables) manufactured by Seller are warranted to be free from defects in workmanship and material under normal use and service for a period of twelve (12) months from the date of shipment by Seller. Consumables, pH electrodes, membranes, liquid junctions, electrolyte, O-rings, etc. are warranted to be free from defects in workmanship and material under normal use and service for a period of ninety (90) days from date of shipment by Seller.
PAGE 98
The right people, the right answers, right now. ON-LINE ORDERING NOW AVAILABLE ON OUR WEB SITE http://www.raihome.com Specifications subject to change without notice. Credit Cards for U.S. Purchases Only. Emerson Process Management Liquid Division 2400 Barranca Parkway Irvine, CA 92606 USA Tel: (949) 757-8500 Fax: (949) 474-7250 http://www.raihome.com © Rosemount Analytical Inc.