BP7404-1 Tilo 2/21/11 2:49 PM Page 1 READ AND SAVE THESE INSTRUCTIONS TILO™ Damp Location 30” Mini Ceiling Fan Owner's Manual Model Numbers: CF130BS00 Brushed Steel CF130ORB00 Oil Rubbed Bronze CF130WW00 Appliance White Net Weight: Part No. F40BP74040001 10.6 Lbs. Form No. BP7404-1 UL Model No.
BP7404-1 Tilo 2/21/11 2:49 PM Page 2 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally.
BP7404-1 Tilo 2/21/11 2:49 PM Page 3 THIS FAN IS SUITABLE FOR DAMP LOCATIONS SUCH AS COVERED PORCHES, COVERED PATIOS, AND COVERED DECKS... ANYWHERE THERE IS A ROOF OVERHEAD. USE ONLY WITH LIGHT KITS MARKED SUITABLE FOR USE IN DAMP LOCATIONS. This Manual is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly Installed Wire Length Up to 50 ft. 50-100 ft.
BP7404-1 Tilo 2/21/11 2:49 PM Page 4 A. FAN MOTOR ASSEMBLY B. HANGER BRACKET C. 4.5" DOWNROD ASSEMBLY D. CEILING COVER E. DECORATIVE LOWER COVER 4 3 I. SW46 WALL CONTROL 2 1 0 F. COUPLER COVER H. SWITCH HOUSING J. LOOSE PARTS BAG G. FAN BLADES (3) a. b. c. d. e. f. g. h. i. j. Fan motor assembly One hanger bracket One 4.5” downrod assembly One ceiling cover One decorative lower cover One coupler cover Three fan blades One switch housing One SW46 wall control One loose parts bag containing: 1.
BP7404-1 Tilo 2/21/11 2:49 PM Page 5 Electrical Requirements NOTE: Take care not to scratch fan housing assembly when installing blades. Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. M5 x 14mm FLANGE HEAD BLADE SCREWS (2 per blade) The outlet box must be securely anchored and capable of withstanding a load of at least 35 pounds.
BP7404-1 Tilo 2/21/11 2:49 PM Page 6 7. Position the switch housing assembly on the switch housing plate and align the holes in the switch housing assembly with the holes in the plate. Secure the switch housing assembly by installing the three previously removed M4 x 8mm flat head screws (Figure 3). PIN HANGER BALL DOWNROD SETSCREW WARNING ! To avoid possible fire or shock, do not pinch wires between the switch housing assembly and the bracket switch housing assembly. Figure 4 3.
BP7404-1 Tilo 2/21/11 2:49 PM Page 7 4. While pulling up on the downrod, securely tighten the two setscrews in the motor coupling (Figure 6). NOTE: The setscrews must be properly installed as described above, or fan wobble could result. 7. Reinstall the hanger ball (Figure 8) on the downrod as follows. Route the motor leads through the downrod. Position the pin through the two holes in the downrod and align the ball so the pin is captured in the groove in the top of the hanger ball.
BP7404-1 Tilo 2/21/11 2:49 PM Page 8 Installing the Ceiling Cover on the Fan Motor Housing Installation of Hanger Bracket ! (For Close-to-the-Ceiling Mounting) WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 11). NOTE: The decorative lower cover, coupler cover and hanger ball assembly are not needed for close-to-the-ceiling mounting. CEILING 1. Remove and retain three screws from the top of the motor housing (Figure 9). 2.
BP7404-1 Tilo 2/21/11 ! 2:49 PM Page 9 How to Hang Your Ceiling Fan For Closeto-the-Ceiling Mounting WARNING To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. ! 1.
BP7404-1 Tilo 2/21/11 2:49 PM Page 10 NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. How to Hang Your Ceiling Fan For Standard Mounting 1. Carefully lift the fan assembly and seat the hanger ball in the hanger bracket (Figure 15). The tab on the hanger bracket must seat in the groove in the hanger ball. ! 1.
BP7404-1 Tilo 2/21/11 ! 2:49 PM Page 11 Installation of Ceiling Cover For Standard Mounting WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. 1.
BP7404-1 Tilo 2/21/11 2:49 PM Page 12 Using Your Ceiling Fan Accessories 1. Downrod Extension Kits (see store or catalog). 2. Ceiling Fan Controls (see store or catalog). 3. Light Kits (see store or catalog). 4 3 2 ! 1 WARNING The use of any other control not specifically approved for this fan could result in fire, shock and personal injury.
BP7404-1 Tilo 2/21/11 2:49 PM Page 13 WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR ! CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE 1. Fan will not start. PROBABLE CAUSE 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan. 2. Fan sounds noisy. 1. Blades not attached to fan. 2. Screws securing fan blades to motor are loose. SUGGESTED REMEDY 1. Check main and branch circuit fuses or circuit breakers.
BP7404-1 Tilo 2/21/11 2:49 PM Page 14 Repair Parts Listing Damp Part Numbers Key No. Description Model No. CF130BS00 Model No. CF130ORB00 Model No. CF130WW00 762231-4 — — — 762231-8 — — — 762231-1 — — — * 1 2 3 Hanger Pack Consisting of: Hanger Bracket Assembly Hanger Ball Downrod, 4.
BP7404-1 Tilo 2/21/11 2:49 PM Page 15 Repair Parts 1 2 18 4 3 3 14 15 4 11 2 1 0 5 6 12 7 19 20 21 17 22 16 8 10 13 9 Before discarding packaging material, be certain all parts have been removed. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • PART DESCRIPTION • NAME OF ITEM • MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing. For repair parts, phone 1-800-654-3545.
BP7404-1 Tilo 2/21/11 2:49 PM Page 16 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for the lifetime of your ceiling fan.
