READ AND SAVE THESE INSTRUCTIONS TM MAUI BAY™ Damp Location Ceiling Fan Owner's Manual Model Numbers CF2000AB02 - Antique Brass CF2000AP02 - Antique Pewter CF2000ORB02 - Oil Rubbed Bronze Net Weight: 26.0 Lbs. Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday Part No. F40BP73230002 Revision: 130605 1-800-654-3545 www.emersonfans.com Form No. BP7323-2 U.L. Model No.
READ AND SAVE THESE INSTRUCTIONS Safety Instructions ! 3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 22.7kg. (50 lbs.) or less”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. 4.
Unpacking Instructions ! PACKAGE CONTENTS WARNING Do not install or use fan if any part is damaged or missing. Call Toll-Free: Part A 1-800-654-3545 B Motor Cover 1 C Ceiling Cover 1 D Fan Blade Flanges 3 E Hanger Bracket 1 F Hanger Ball/Downrod Assembly 1 G Switch Housing Cover 1 ! WARNING This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co.
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Up to 50 ft. 50-100 ft. Tools Needed for Assembly One Phillips head screwdriver One wire stripper One stepladder ! Materials Wire Size A.W.G. 14 12 WARNING Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 8).
Ceiling Fan Assembly 1. Remove the fan motor and housing assembly from styrofoam packaging and position it so that the top of the motor is facing you. MOTOR LEADS (BLACK, WHITE, AND BLUE) 2. Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly and seat the downrod in the motor coupling (Figure 1).
Ceiling Fan Assembly (continued) 6.Screw two 1” threaded studs (supplied) into the motor (Figure 4). Leave approximately 7/8” of the stud extending above motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two lockwashers and knurled knobs (supplied) to secure the cover.
How to Hang Your Ceiling Fan ! CEILING WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 6). ! WARNING AT LEAST 7' The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. Use only a U.L. outlet box listed as “Acceptable for Fan Support of 22.7kg. (50 lbs.) or less”. ! WARNING FLOOR To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support of 22.7kg. (50 lbs.
How to Wire Your Ceiling Fan & Install the Control If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation) (Figure 9). Securely connect wires with wire connector supplied.
Fan Blade Installation 1. Use four 10-32 x 3/8” pan head screws and flat washers (supplied) to secure the flange to the fan blade (ordered separately) (Figure 11). Repeat for the remaining four blades. 10-32 x 3/8" PAN HEAD SCREW FLAT WASHER FAN BLADE 2. Use the 10 round recessed holes in the motor hub marked with "5" and install the five blade assemblies in accordance with Step 3. 3. Attach one blade assembly to the motor hub using two 10-32 x 5/8" oval head screws (supplied) (Figure 12).
Using Your Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. 2. Check the operation of the fan by gently pulling on the 4-position speed control pull chain switch. The operating sequence is as follows: 3. If airflow is desired in opposite direction, turn your fan off and wait for the blades to stop turning, then press the rocker switch located on top of the motor housing, and turn the fan on again.
Accessories 1. Ceiling Fan Light Kits (see store or catalog). 2. Downrod Extension Kits (see store or catalog). 3. Ceiling Fan Controls (see store or catalog). ! ! WARNING This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.
Repair Parts 2 1 3 16 14 6 15 18 17 13 17 18 31 30 27 5 4 29 21 22 23 8 7 25 9 19 26 10 28 24 20 12 12 11 U.L. Model No.
Repair Parts Listing Model Numbers Key No. 1 2 3 4 5 11 12 14 15 16 17 18 19 20 21 22 29 30 6 7 8 9 10 13 23 24 25 26 27 28 30 — *Fan blade Description CF2000AB02 CF2000AP02 CF2000ORB02 Hanger Bracket Assy.
Notes 14 U.L. Model No.
Emerson Air Comfort Ceiling Fan Limited Warranty What The Limited Warranty Covers: This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original retail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and accessories of the Emerson Ceiling Fan against all defects in workmanship and materials.
Air Comfort Products DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant • St. Louis, MO 63136 Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday 1-800-654-3545 www.emersonfans.com Retain this manual for future use. Part No. F40BP73230002 Revision: 130605 Printed in China 06/13 Form No. BP7323-2 U.L. Model No.
