BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 1 READ AND SAVE THESE INSTRUCTIONS HIGHRISE™ 50” Ceiling Fan Owner's Manual Model Numbers CF430BS00 Brushed Steel CF430ORB00 Oil Rubbed Bronze CF430SW00 Satin White Net Weight: 24.3 Lbs. Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., Eastern, Monday-Friday Part No. F40BP74860000 Revision: 131212 1-800-654-3545 www.emersonfans.com Form No. BP7486 ETL Model No.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 2 Table of Contents Section Page 7. Wall Control Procedures . . . . . . . . . . . . . . . . . . . . . .14-18 8. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 9. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 10. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21 11. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 12.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 3 1. Unpacking Instructions PACKAGE CONTENTS WARNING ! Do not install or use fan if any part is damaged or missing. Call Toll-Free: Part 1-800-654-3545 A B WARNING ! This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 4 1. Unpacking Instructions (continued) This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Up to 50 ft. 50-100 ft. Tools Needed for Assembly One Phillips head screwdriver One 1/4” blade screwdriver One stepladder One wire stripper ! Materials Wire Size A.W.G.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 5 3. Ceiling Fan Assembly 3.1 PIN Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1). Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in Step 3.6. HANGER BALL SETSCREW DOWNROD Figure 1 3.2 Loosen setscrew in motor coupling if necessary. Separate, untwist and unkink the three 80” motor leads.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 6 3. Ceiling Fan Assembly (continued) 3.5 Place the ceiling cover over the downrod. Be sure both the ceiling cover and the coupler cover are oriented correctly (Figure 4). DOWNROD CEILING COVER COUPLER COVER Figure 4 3.6 Reinstall the hanger ball (Figure 5) on the downrod as follows. Route the motor leads through the downrod.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 7 4. How to Hang Your Ceiling Fan ! WARNING CEILING The fan must be hung with at least 7' of clearance from floor to blades (Figure 6). AT LEAST 7' FLOOR Figure 6 ! WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. Use only a U.L. outlet box listed as “Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less”.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 8 4. How to Hang Your Ceiling Fan (continued) 4.2 Screw the two 1-1/4” threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 8). OUTLET BOX HANGER BRACKET 1-1/4" THREADED STUDS (2) ANTI-ROTATION TAB Figure 8 4.3 NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY. Carefully lift the fan and seat the hanger ball/ downrod assembly into the hanger bracket that was just attached to the outlet box (Figure 9).
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 9 5. How to Wire Your Ceiling Fan 5.2 If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Refer to Figures 10 and 11 and connect the receiver wires to the supply wires and the fan motor wires as follows: CAUTION: To reduce the risk of electrical shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver. a.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 10 5. How to Wire Your Ceiling Fan (continued) ! WARNING ! This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 11 6. Final Assembly 6.1 BLADE SLOTS (4) Slide the fan blade through the blade slot in the flywheel. (Figure 12). FAN BLADES (4) Mount the fan blade to the fan housing using three #8 - 32 x 11mm washer head blade screws (Figure 12). NOTE: Take care not to scratch fan housing assembly when installing blades. Complete installation of the remaining three blades per the above instructions.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 12 6. Final Assembly 6.4 Remove one of the three #8 - 32 x 3/8” truss head screws from the light kit plate adapter (Figure 15). Retain the screw for future installation. Loosen the other two screws. Carefully tuck all the wires under the light fixture assembly prior to installing the light fixture assembly onto the light kit plate adapter. Place the light fixture assembly onto the light kit plate adapter.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 13 6. Final Assembly (continued) 6.6 Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 17). CEILING COVER 6.7 Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs (supplied). (Figure 17).
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 14 INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 15 7. Wall Control Procedures (continued) 7.3 WALL CONTROL CODE SWITCHES Your wall control has code switches which must be set in one of 32 possible code combinations (Figure 19). The five levers (numbered 1, 2, 3, 4, and 5) on the switches are factory-set in the ON (up) position. Change the switch settings as follows: ON 1 2 3 4 5 I 7.4 Slide the five switch levers in the wall control to your choice of ON (up) or down positions.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 16 7. Wall Control Procedures (continued) SINGLE-POLE INSTALLATION (continued) 3-WAY INSTALLATION 7.8 (One fan controlled by two different wall controls) (See Figures 22 and 23.) Requires purchase of accessory SW406 wall control. Before installing wall control, place wall control in “OFF” mode by pushing “ON/OFF” switch to the “OFF” position. ! Turning off wall switch is not sufficient.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 17 7. Wall Control Procedures (continued) 3-WAY WIRING DIAGRAM: NEW CONSTRUCTION STANDARD WIRING FOR EXISTING 3-WAY CONTROLS NOTE: Retrofit 3-way installations are likely to include two traveler wires between the two wall boxes. In new construction, only one traveler wire Is required (See Figure 23). HOT BLK BLACK ! EXISTING WALL CONTROL WARNING Check to see that all connections are tight and that no bare wires are visible at the wire connectors.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 18 7. Wall Control Procedures (continued) PROGRAMMING THE RECEIVER OPERATING FREQUENCY & HIGH SPEED CONDITIONING OF FAN CONTROL 7.24 Within 1 minute of restoring electricity to the ceiling fan, push and hold the fan OFF button ( ) for 3 to 5 seconds to set the code in the receiver. The ceiling fan lights (if installed) will blink to indicate the transmitted has been paired with the receiver. 7.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 19 8. Maintenance IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan ! WARNING Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 20 10. Repair Parts 1 2 6 4 3 5 14 6 7 7 8 8 15 5 4 9 10 11 16 12 21 13 9 18 ON 22 17 10 19 11 .... 20 20 OFF ON 23 ETL Model No.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 21 10. Repair Parts Listing Model Numbers Key No. Description CF430BS00 CF430ORB00 CF430SW00 * 1 2 3 Hanger Ball Assembly, Consisting of: Hanger Bracket Hanger Ball Downrod (4.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 22 11. Trouble Shooting ! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. TROUBLE 1. Fan will not start. PROBABLE CAUSE SUGGESTED REMEDY 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. 2.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 23 Emerson Air Comfort Ceiling Fan Limited Warranty What The Limited Warranty Covers: This limited warranty is offered by Air Comfort Products division of Emerson Electric Co.
BP7486 CF430 Highrise OM 12/13/13 10:35 AM Page 24 Air Comfort Products DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant • St. Louis, MO 63136 Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., Eastern, Monday-Friday 1-800-654-3545 www.emersonfans.com Retain this manual for future use. Part No. F40BP74860000 Revision: 131212 Printed in China 12/13 Form No. BP7486 ETL Model No.
