READ AND SAVE THESE INSTRUCTIONS CF711 shown 42” PRO SERIES II Model No. CF710AB02 CF710AW02 CF710BS02 CF710ORB02 CF710PB02 CF710WW02 Net Weight: 15.0 Lbs. 50” PRO SERIES II Model No. CF711AB02 CF711ORS02 CF711AW02 CF711PB02 CF711BS02 CF711WB02 CF711CK02 CF711WW02 CF711ORB02 Net Weight: 19.8 Lbs. PRO SERIES II Ceiling Fan Owner's Manual Part No. F40BP72580008 Form No. BP7258-8 U.L. Model No.
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3.
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder One 1/4” blade screwdriver One wire stripper Three wire connectors (supplied). Four 13W E26 medium base bulbs CFL (CF711) Three 13W E26 medium base bulbs CFL (CF710) Installed Wire Length Up to 50 ft. 50-100 ft. WARNING ! MATERIALS Wiring outlet box and box connectors must be of type required by the local code.
IMPORTANT HANGER BALL/DOWNROD ASSEMBLY DECORATIVE CAP Your ceiling fan is designed to be installed either in the standard manner, or in the close-to-the-ceiling manner. Using the standard method, the hanger ball/downrod assembly will suspend the fan several inches below the ceiling cover. Using the close-to-the-ceiling method, the ceiling cover installs directly on the fan motor housing, thus mounting the fan 3-1/2 inches closer to the ceiling than the standard method.
NOTE: The hanger bracket must be mounted flush with the ceiling in order for the ceiling cover to install properly. If necessary, use leveling washers (not supplied) between the outlet box and the hanger bracket. 2. Slide the hanger bracket onto the outlet box screws. Center the bracket over the outlet box and then securely tighten the screws (Figure 6). Installing The Hanger Bracket ! WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 4).
Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. HANGER BRACKET HOOK TAB ! To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws supplied with outlet box.
2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 9). Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using wire connector supplied (Figure 9). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box.
2. Mount one blade assembly to the motor hub by mating the alignment post (Figure 11) of the flange with one of the alignment slots in the motor hub (Figure 12). Then tighten the two captive screws in the flange to secure the flange to the motor hub. Repeat this procedure for the other four blade assemblies. Make sure all screws are tightened. Removal Of The Light Fixture NOTE: In some instances it may be desirable to install the ceiling fan without the light fixture.
Using Your Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. SPEED CONTROL PULL CHAIN SWITCH 2. Check the operation of the light by gently pulling on the light switch pull chain. REVERSING SWITCH 3. Check the operation of the fan by gently pulling on the speed control switch pull chain. The operation sequence is as follows: 1st pull - High 3rd pull - Low 2nd pull - Medium 4th pull - OFF LIGHT PULL CHAIN SWITCH 4.
Maintenance Accessories 1. Ceiling Fan/Light Controls (see store or catalog). 2. Downrod Extension Kits (see store or catalog). IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed. ! The use of any other control not specifically approved for this fan could result in fire, shock and personal injury. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish.
Repair Parts 1 2 3 9 10 11 17 16 15 4 8 6 5 7 12 13 13 14 Before discarding packaging material, be certain all parts have been removed. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • NAME OF ITEM • PART DESCRIPTION • MODEL NUMBER For repair parts, phone 1-800-654-3545. 11 U.L. Model No.
Repair Parts Listing Key No.
