User manual
INSTALLATION
Unravel the 
AC 
cord and 
connecl 
tt to 
a
convenrently 
located AC 
outlet having 
120V
and 60Hz 
only. The 
Clock 
Display 
will
illumrnate 
and 
a flashing 
trme 
wtll appear 
tn 
the
wrndow 
The 
Clock 
Displav 
will conttnue 
to
flash 
untilthe 
ttme has 
been 
set
NOTE lf the 
AC 
plug 
does not 
fit into 
a nonpolarized 
outlet. 
do 
not file or 
cut
the 
wide blade
lf the AC 
cord 
is drsconnected 
or 
if 
there 
is a 
power 
failure, this electronic
clock 
is designed 
to continue operating 
rnternally 
(withoLrt 
showtng 
the time 
on
the 
Clock Display) 
wtth a 
9 volt battery 
(not 
tncluded)
To connect 
the battery. 
locate 
the
Battery 
Compartment 
on 
the 
bottom 
of
the 
unit 
Connect 
the battery 
to the
termtnals 
of the battery 
snap 
tnstde tito.
compartment 
(use 
of 
an alkalrne
battery 
is recommended). 
Cltp 
the
battery 
back 
into the holder 
in the
compartment.
BATTERY PRECAU] 
IONS
I 
OAI 
lEnI  rnLvnvrrvltJ
| 
| 
ott,,* 
lfrese 
precautlons 
when usttig 
battercs 
in this 
.Jellce
1  Llse oniy lhe 
srze and type 
of battenes specllied
2 Be sure 
to 
lollow 
the c()rrect 
polar(V 
r!hen inslalling 
lhe batlenes 
as
Indicated rn the battery 
comparlrnent 
Reversed batlerles 
may
cause damage 
to the devtce.
3 
[-]o 
nol mix 
dillerenl types of battertes 
logether 
(e 
g Alkaline and
Carbon-zrnc) 
or old ballefles 
wtth 
lresh ones
.1 
lt 
tfle 
devrce 
rs not 
lo be used 
lor a long 
penod 
of lime 
rernove 
the
banenes lo 
prevent 
damalle or 
InJury 
lrom 
possible battery leakage
5 Do not try 
lo 
recharge 
ballenes 
not rntended 
to 
be 
recharged, they
can overheat and 
rupture 
lFolbw 
battery 
rnanufaclurels 
direclions.)
Be sure to check the 
condition 
of the battery 
periodically 
by disconnecting 
the
AC 
cord and connecting 
it again 2 or 3 
minules later. 
The 
preset 
times
should continue operating. 
lf a 
flashing ttme 
appears on 
the Clock Display, 
it
indicates 
the 
battery 
rs dead or 
not connected 
properly. 
The 
9 volt battery 
will
keep 
the 
internal 
times accurately 
for approximately 
30 minutes. 
lf the 
power
rs 
restored 
after 
30 minutes, the times 
may 
need to be 
reset.
.a
I
\
'Al 
; 
lttrl
rl
\
AC Outlet
-t
m
o)
-
or'
a
I
I
\
\__---
|- 
il
,i
1r 
jr
d 
ili
I 
tl
i; 
tt
t--rl
\-










