User’s Manual Questions or Comments? Call 1-888-923-2323
Comfort Alert® Diagnostics – Faster Service And Improved Accuracy Comfort Alert is a breakthrough innovation for troubleshooting heat pump and air conditioning system failures. The module easily installs in the electrical box of the outdoor unit near the compressor contactor. By monitoring and analyzing data from the Copeland Scroll® compressor and the thermostat demand, Comfort Alert can accurately detect the cause of electrical and system related failures without any sensors.
Application, Benefits And Product Specifications Part Number: (Service Number) Application 543-0010-00 543-0010-01 (943-0010-00) (943-0010-01) 543-0012-00 (943-0012-00) 543-0032-00 Heat Pump: Single A/C and Heat Pump: A/C: Single Stage Stage with Copeland Single Stage with with Copeland Scroll® Scroll® Copeland Scroll® 543-0033-02 (943-0033-00) A/C and Heat Pump: Two Stage with Copeland Scroll® UltraTech Benefits Diagnostic Alert Codes ü ü ü ü Trip Indicator ü ü ü ü Data Port ü ü ü ü ü
Part Numbers: 543-0010-00, 943-0010-00, 543-0012-00, 943-0012-00 A. 1.81 in (46 mm) B. 2.44 in (62 mm) C. 1.43 in (36 mm) D. 3.15 in (80mm) E. 2.44 in (62 mm) Figure 2 Part Numbers: 543-0010-01, 943-0010-01 A. 1.81 in (46 mm) B. 2.44 in (62 mm) C. 1.43 in (36 mm) D. 3.15 in (80mm) E. 2.
Part Numbers: 543-0032-00, 943-0033-00, 543-0033-02 A. 1.85 in (47 mm) B. 2.44 in (62 mm) C. 1.46 in (37 mm) D. 4.40 in (112mm) E. 2.44 in (62 mm) Figure 4 Compressor Wire Routing (Figure 5) The scroll compressor’s run (R), common (C) and start (S) wires are routed through the holes in Comfort Alert marked “R,” “C” and “S.” The common (C) wire need not be routed through the module for it to operate properly.
Note: 24VAC power wiring is not required for 2 wire Comfort Alert, which is powered by the demand (Y terminal). Even if the 24VAC power supply is available it should not be connected. Refer to Figure 7. Thermostat Demand Wiring Comfort Alert requires a thermostat demand signal to operate properly. The thermostat demand signal input, labeled Y on the module, should always be connected to the compressor contactor coil so that when the coil is energized, the demand signal input is 24VAC.
Figure 7: Air Conditioning Schematic 543-0010-01, 943-0010-01 Solid Line shows field installed wiring. LPCO HTCO Dashed line shows thermostat demand wiring in system without HTCO, LPCO.
Figure 9: Air Conditioning or Heat Pump Schematic 543-0032-00 Solid Line shows field installed wiring. LPCO Dashed line shows thermostat demand wiring in system without HTCO, LPCO and Defrost.
L Terminal Wiring (Part Numbers 543-0032-00, 543-0033-02, 943-0033-00) The L connection is used to communicate Alert codes to compatible White-Rodgers® thermostats. The L terminal of the thermostat should be connected directly to the Comfort Alert L terminal. On select White-Rodgers thermostats, an icon on the thermostat display will flash at the same rate as the Comfort Alert yellow Alert LED.
Interpreting The Diagnostic LEDs When an abnormal system condition occurs, the Comfort Alert module displays the appropriate ALERT and/or TRIP LED. The yellow ALERT LED will flash a number of times consecutively, pause and then repeat the process. To identify a Flash Code number, count the number of consecutive flashes. Every time the module powers up, the last ALERT Flash Code that occurred prior to shut down is displayed for one minute.
LED Troubleshooting Information Status LED Green “POWER” Red “TRIP” Yellow “ALERT” Flash Code 1 Yellow “ALERT” Flash Code 2 Status LED Description Module has power Status LED Troubleshooting Information Supply voltage is present at module terminals Thermostat demand signal Y is present, but the compressor is not running 1.Compressor protector is open • Check for high head pressure • Check compressor supply voltage 2.Outdoor unit power disconnect is open 3.
LED Troubleshooting Information Continued Status LED Status LED Description Yellow “ALERT” Flash Code 3 Short Cycling Compressor is running only briefly Yellow “ALERT” Flash Code 4 Locked Rotor Yellow “ALERT” Flash Code 5 Open Circuit Yellow “ALERT” Flash Code 6 Open Start Circuit Current only in run circuit Yellow “ALERT” Flash Code 7 Open Run Circuit Current only in start circuit Yellow “ALERT” Flash Code 8 Welded Contactor Compressor always runs Yellow “ALERT” Flash Code 9 Low Voltage Cont
NOTE: The correct Comfort Alert model must be used for the application (refer to the Application, Benefits and Product Specifications section on page 3). If the wrong model is installed, or Comfort alert is wired incorrectly, the ALERT Flash Codes for system faults may function incorrectly: Comfort Alert may indicate system faults that are not present or fail to indicate system faults that are present.
Warranty Information Emerson Climate Technologies, Inc. warrants its enclosed diagnostic module to be free from defects in materials and workmanship under normal use for a period of one year from the date of purchase or twenty months from manufacture whichever comes first. During this period, we will replace any defective diagnostic module without charge. This warranty is valid for the original purchaser from the date of initial purchase and is not transferable. Keep the original sales receipt.
Información de Garantía Emerson Climate Technologies, Inc. garantiza que su modulo de diagnóstico adjunto no tendrá defectos de materiales o de trabajo bajo un uso normal por un periodo de un año a partir de la fecha de compra o bien por veinte meses a partir de la fecha de fabricación, tomando como válida la fecha de primer vencimiento. Durante este período, we recambiará cualquier módulo de diagnóstico defectuoso sin cargo alguno.
AVISO: Se debe usar el modelo correcto de Confort Alert para la aplicación (refiérase a la sección Aplicación, Beneficios y Especificaciones del Producto en la página 3). Si se instala el modelo incorrecto, o el Confort Alert es cableado de forma errónea, los Códigos de Destello de ALERTA para fallas del sistema pueden funcionar incorrectamente: el Confort Alert puede llegar a indicar fallas que no existan o puede no indicar fallas que se están produciendo en el sistema.
Información de Detección y Arreglos de Fallas del LED – Continuación Circuito Abierto 1. La desconexión de energía de la unidad de exteriores está abierta 2. El interruptor de circuito del compresor o los fusibles están abiertos 3.
Información de Detección y Arreglos de Fallas del LED Información de Detección y Arreglo de Fallas del LED de Estado Hay suministro de voltaje en los terminales del modulo 1. El protector del compresor está abierto • Cotnrole si hay presión alta • Controle el voltaje de suministro del compresor 2. La desconexión de energía de la unidad de exteriores está abierta 3. El interruptor de circuito o fusible(s) está abierto 4. Cables de suministro rotos o el conector no están haciendo contacto 5.
Interpretación de los LED de Diagnóstico Cuando se produce una condición anormal del sistema, el modulo Confort Alert indicará el LED DE ALERTA correspondiente y/o el LED DE DISPARO. El LED DE ALERTA amarillo destellará una cantidad de veces consecutivamente, hará una pausa y repetirá el proceso. Para identificar un número de Código de Destello, cuente el número de destellos consecutivos.
Cableado del Terminal L (Números de Parte 543-0032-00, 543-0033-02, 943-0033-00) La conexión L se usa para comunicar códigos de Alerta a los termostatos compatibles de White-Rodgers®. El terminal L debe estar conectado directamente al terminal L del Confort Alert. Al seleccionar los termostatos White-Rodgers, destellará un ícono en el termostato a la misma tasa que el LED de Alerta amarillo del Confort Alert.
Figura 9: Esquema de Aire Acondicionado o Bomba de Calor 543-0032-00 L’nea de l’quido muestra el cableado instalado en el campo L’nea punteada muestra el cableado de demanda del termostato en el sistema sin HTCC, LPCO ni Descongelamiento M—dulo de Diagn—stico Confort Alert 543-0032-00 LPCO HTCO HPCO Y L ECB R C C R L Y1 Bloque Terminal de la Unidad de Interiores C R L Y1 Termostato de Interiores de Etapa ònica Descripci—n de Abreviaturas del Esquema HTCO Interruptor de Corte por Presi—n Alt
Figura 7: Esquema de Aire Acondicionado 543-0010-01, 943-0010-01 Solid Line shows field installed wiring. LPCO HTCO Dashed line shows thermostat demand wiring in system without HTCO, LPCO.
Nota: No se requiere cableado de corriente de 24VCA para el módulo Confort Alert de 2 cables, el que está energizado por la demanda (terminal Y). Incluso si el suministro de energía está disponible, no deberá conectarse. Refiérase a la Figura 7. Cableado de Demanda del Termostato El modulo Confort Alert requiere una señal de demanda del termostato para operar correctamente.
Números de Parte: 543-0032-00, 943-0033-00, 543-0033-02 A. 1.85 pulg. (47 mm) B. 2.44 pulg. (62 mm) C. 1.46 pulg. (37 mm) D. 4.40 pulg. (112mm) E. 2.44 pulg. (62 mm) ENERGIA DISPARO DE ALERTA Figura 4 Tendido del Cableado del Compresor (Figura 5) Los cables de recorrido (R), común (C) y de arranque (S) del compresor scroll están tendidos a través de orificios en el módulo Confort Alert marcados “R,” “C” y “S”.
Números de Parte: 543-0010-00, 943-0010-00 543-0012-00, 943-0012-00 A. 1.81 pulg. (46 mm) B. 2.44 pulg. (62 mm) C. 1.43 pulg. (36 mm) D. 3.15 pulg. (80mm) E. 2.44 pulg. (62 mm) ENERGIA DISPARO DE ALERTA Figura 2 Part Numbers: 543-0010-01, 943-0010-01 A. 1.81 in (46 mm) B. 2.44 in (62 mm) C. 1.43 in (36 mm) D. 3.15 in (80mm) E. 2.
Aplicaciones, Beneficio y Especificaciones del Producto 19-28VCA, 48-62 Hz -40° a 175° F (-40° a 80° C) -40° a 150° F (-40° a 65° C) Rango de Suministro de Energía Temperatura de Almacenado Temperatura Operativa 0.5 VA nominal 0.5 VA nominal Requisitos Energèticos Usar sólo con circuitos Clase 2 Usar sólo con circuitos Clase 2 Restricciones UL 19-28VCA, 48-62 Hz -40° a 175° F (-40° a 80° C) -40° a 150° F (-40° a 65° C) Usar sólo con circuitos Clase 2 1.
Diagnósticos Comfort Alert® – Un Servicio Más Rápido y Una Mayor Precisión El modulo de diagnóstico de Comfort Alert es una innovación revolucionaria para la detección y arreglo de fallas en bombas de calor y sistemas de aire acondicionado. El módulo se instala fácilmente en la caja de electricidad de la unidad de exteriores, cerca del contactor del compresor.
Manual del Usuario