Instruction manual

ControlWave Micro Instruction Manual (CI-ControlWave Micro)
IND-2 Index Revised May-2011
F
Features.............................................................. 1-1
Field repair.......................................................... 5-5
Figures
1-1. 8 slot Base Housing ................................ 1-3
1-2. CPU Module with Three Serial Ports and
optional Ethernet Port .................................. 1-5
1-3. CPU Module with Two Serial Ports and Two
Ethernet Ports .............................................. 1-6
1-4. PSSM with Run/Local/Remote Switche.. 1-8
1-5. PSSM with Mode Switch......................... 1-8
1-6. Expansion Communications (ECOM)
Module.......................................................... 1-9
1-7. Two ControlWave Micro I/O Modules with
bezel........................................................... 1-10
1-8. ControlWave Programming Environment ..1-
11
2-1. 8-Slot Base Housing with Bezel.............. 2-4
2-2. 3-Slot Base Housing ............................... 2-5
2-3. 4-Slot Base Housing ............................... 2-5
2-4. 8 Slot Base Housing................................ 2-6
2-5. 2-Slot Expansion Housing....................... 2-6
2-6. 4-Slot Expansion Housing....................... 2-7
2-7. 8-slot Expansion Housing ....................... 2-7
2-8. JP2, JP3, and JP4 Jumpers on Base
Housing ........................................................ 2-8
2-9. PSSM with Run/Remote/Local Switch,
Display Interface, and Watchdog Connector ..2-
10
2-10. PSSM Module with Mode Switch, Display
Interface, and without Watchdog Connector...2-
11
2-11. PSSM TB1 Wiring ............................... 2-15
2-12. Watchdog MOSFET Switch Wiring..... 2-16
2-13. CPU Module with Three Serial Ports .. 2-17
2-14. CPU Module with Three Serial Ports and
One Ethernet Port ...................................... 2-18
2-15. CPU Module with Two Serial and Two
Ethernet Ports ............................................ 2-19
2-16. Male DB9 9-Pin Connector ................. 2-24
2-17. Full-duplex and Half-duplex Cable...... 2-25
2-18. Full-duplex and Half-duplex Cable...... 2-25
2-19. Full-duplex and Half-duplex Cable...... 2-26
2-20. RJ-45 Ethernet Connector .................. 2-29
2-21. Standard 10/100Base-T Ethernet Cable
(CPU Module to Hub)................................. 2-29
2-22. Point-to-Point 10/100Base T Ethernet
Cable.......................................................... 2-30
2-23. ECOM1 with Two Serial Ports, a Radio,
and a Modem ............................................. 2-31
2-24. ECOM2 with Two RS-232 and Two RS-
485 Ports.................................................... 2-32
2-25. Full-duplex and Half-duplex Cable...... 2-34
2-26. ECOM Radio Modem Installation........ 2-35
2-27. PTSN Field Connections for ControlWave
Micros......................................................... 2-37
2-28. Phone Cord Wiring.............................. 2-37
2-29 Bezel Assembly.................................... 2-39
2-30 Optional 2-Button and 25-Button Keypads
.................................................................... 2-39
3-1. Module Wiring for Local Termination ...... 3-3
3-2. Module Wiring for Remote Termination .. 3-4
3-3. Isolated DI Module (Local Termination).. 3-7
3-4. Isolated DI Module (Remote Termination,
Internally Sourced or Externally Powered)... 3-8
3-5. Isolated DI Module (Remote Termination,
Internally Sourced or Externally Powered, with
and without Fuses)....................................... 3-9
3-6. Isolated DO Module (Local Termination) .. 3-
11
3-7. Isolate
d DO Module (Remote Termination)
.................................................................... 3-12
3-8. Isolated DO Module (Remote Termination
with Relay Isolated with 24 Vdc) ................ 3-13
3-9. Non-isolated DI/O Module (Local
Termination) ............................................... 3-15
3-10. Non-isolated DI/O Module (Remote
Termination) ............................................... 3-16
3-11. Non-isolated AI/O and AI Module
Configuration (Local Termination).............. 3-19
3-12. Non-isolated AI/O and AI Modules
(Remote Termination) ................................ 3-20
3-13. Non-isolated HSC Module (Local
Termination) ............................................... 3-23
3-14. Non-isolated HSC Module (Remote
Termination) ............................................... 3-24
3-15. Isolated AI Module (Local Termination) .. 3-
27
3-16. Isolated AI Module (Remote Termination)
.................................................................... 3-28
3-17. Isolated AO Module (Local Termination) 3-
30
3-18. Isolated AO Module (Remotely
Terminated)................................................ 3-31
3-19. Non-isolated MI/O Module (Local
Termination) ............................................... 3-34
3-20. Non-isolated MI/O Module (Remote
Termination) ............................................... 3-34
3-21. MI/O Module (Remote Terminatio)...... 3-35
3-22. MI/O Module Wiring (Local Termination) 3-
36
3-23. MI/O Module Wiring (Remote Termination)
.................................................................... 3-37
3-24. Isolated Vac DI Module Wiring (Local
Termination) ............................................... 3-39
3-25. Relay Isolated Vac/Vdc DO Module Wiring
(Local Termination) .................................... 3-41
3-26. Isolated DI/O Module Wiring (Local
Termination) ............................................... 3-44
3-27. Isolated RTD Module Wiring (Local
Termination) ............................................... 3-46
3-28. Isolated RTD Module Wiring (Remote
Termination) ............................................... 3-47
3-29. Isolated LLAI Module Wiring (Local
Termination) ............................................... 3-49
3-30. Isolated LLAI Module Wiring (Remote
Termination) ............................................... 3-50