Brochures and Data Sheets

Model L-N L-G N-G L-L
IE-103
IE-105
IE-110
IE-120
IE-203
IE-205
IE-210
IE-220
Peak Surge Current Capability (8 x 20 µs)
Line to Neutral 15,000 Amps
Line to Ground 15,000 Amps
Neutral to Ground 15,000 Amps
Total 45,000 Amps
Frequency Response (Forward-Reverse)
Normal Mode 100 kHz to 50 MHz - 90 dB Min
Common Mode 5 MHz to 50 MHz - 60 dB Min
Typical Category A Ringwave (6 kV, 200 A, 100 kHz)
Normal Mode/Common Mode
3 Amp 1 V/300 V
5 Amp 0.7 V/292 V
10 Amp 0.7 V/300 V
20 Amp 0.7 V/300 V
Typical Category B Ringwave (6 kV, 500 A, 100 kHz)
Normal Mode/Common Mode
3 Amp 178 V/300 V
5 Amp 162 V/291 V
10 Amp 153 V/300 V
20 Amp 200 V/300 V
MCOV
120 Volt 150 VRMS
240 Volt 275 VRMS
Line Frequency 47 - 63 Hz
Connection Terminal
Mounting Type DIN/Flange
Weight < 3 lbs
Response Time
Normal Mode < 0.5 ns
Common Mode < 5 ns
Operating Temperature -40°C to +45°C
Derate Linearly to 60% at +70ºC
Operating Humidity 0% to 95%
Voltage* Continuous Current Model
120 V 3 Amps IE-103
120 V 5 Amps IE-105
120 V 10 Amps IE-110
120 V 20 Amps IE-120
Voltage* Continuous Current Model
240 V 3 Amps IE-203
240 V 5 Amps IE-205
240 V 10 Amps IE-210
240 V 20 Amps IE-220
* All voltage configurations are single phase - 2 wire + gnd.
Islatrol
™
IE Series
Active Tracking Filter
™
The Islatrol
™
IE is a series-connected DIN or flange mounted high-
frequency noise filter and surge suppressor. Its ideal applications include
critical industrial loads drawing up to 20 Amps of continuous current,
while typical applications include any microprocessor-based products,
including industrial PLCs, OEM applications, and motion control systems.
Features
■ Multi-staged design, combining a unique
hybrid clamping network with the active
tracking technology of the Islatrol
®
family
■ Surge current capacity — 45,000 Amps
■ Transient protection in all modes: line
to neutral, line to ground, and neutral
to ground
■ LED status indication and form C contact
for remote indication
■ DIN mountable enclosure
■ ANSI/UL 1449 Third Edition Type 4,
1283, CUL recognized, CE
■ 10 year warranty
Dimensional Diagram
Performance Technical Specifications
General Technical Specifications
Ordering Information
Filtering/Line Conditioning
6
400V 600V 600V N/A
400V 600V 500V N/A
1,000V 700V
900V 700V
Edco
™
SS64 & SS65 Series
Wastewater/Industrial Applications
The Edco
™
SS64 and Edco
™
SS65 Series suppressors are designed for the water
and wastewater industry. These multi-stage hybrid suppressors address
over-voltage transients with gas tube and silicon avalanche technology. In
addition, sneak and fault currents are mitigated with PTC devices which
consist of solid-state resettable fuses. The units are encapsulated in stainless
steel pipe nipples making them suitable for use in severe environments. The
Edco
™
SS64 models protect a signal pair and the Edco
™
SS65 models protect a
signal pair plus the cable shield (drain wire).
Features
■ Transient protection for
low-voltage signal lines
■ Sneak/fault current protection
■ Resettable fusing—PTCs
■ Differential and common mode protection
■ Automatic recovery
■ Encapsulated in stainless steel
pipe nipples
■ Protection for one pair
(Two wires & shield on SS65)
■ 5 year warranty
Response Time < 1 Nanosecond
Maximum Signal Voltage 28 V Max
DC Clamping Level (L-G) 36 V ±l0%
DC Clamping Level (L-L) 72 V ±l0%
Maximum let-thru Voltage:
Line-to-Ground (10x700 µs) 44 V @ 400 A
Maximum let-thru Voltage:
Line-to-Line (10x700 µs) 90 V @ 400 A
Series Resistance (per conductor) 5 V (typical)
Capacitance:
(Zero Volts Bias) (L-L) 600 pf typical
(L-G) 1200 pf typical
Number of Occurrences 400 @ 500 Amps
(10x1000 µs)
General Technical Specifications Typical Applications
Caution: The hybrid design of this product includes series resistance. Do not place this product
in service on any signal lines capable of supplying more than 150 milliamperes continuously.
Data/Signal Line Protection
19