Owner's Manual

· minimum distances 10 cm around the apparatus for sufficient ventilations.
10cm de distance minimale autour de l’appareil pour une ventilation suffisante.
·t he ventilation should not be impeded by covering the ventilation openings with items such
as newspaper, table-cloths, curtains etc.
Ne pas recouvrir les entrées d’aérations avec des objets tel qu’un journal, une nappe, un
rideau, etc…
· no naked flame sources such as lighted candles should be placed on the apparatus.
Aucune source de flamme nue, tel qu’une bougie, ne doit être placée sur l’appareil.
·attention should be drawn to the environmental aspects of battery disposal.
Les piles usages doivent être jetées en respectantl’environnement.
·the use of apparatus in tropical and/or moderate climates.
L’utilisation de l’appareil dans un climat tropical et/ou modéré
Maximum recommended ambient temperature is 25°C.
La prise du secteur ne doit pas ētre obstruée ou doit ētre facilement accessible pendant
son utilisation.
Pour étre complètement déconnecté de l'alimentation d'entrée, la prise doit ētre
débranchée du secteur.
Les piles ne doivent pas ētre exposées à de forte chaleur, tel qu'á la lumière du soleil, au
feu ou autres choses de semblable.
La prise du secteur est utilisé pour déconnecter le système.
La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant
son utilisation.
Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être
débranchée du secteur.
L’adaptateur AC/AC de l’appareil est utilisé pour déconnecter le système.
L’adaptateur AC/AC de l’appareil ne doit pas être obstrué ou doit être facilement
accessible pendant son utilisation.
Pour être complètement déconnecté de l’alimentation d’entrée, l’adaptateur AC/AC de
l’appareil doit être déconnecté du secteur.
WARNING
Do not ingest the battery,Chemical Burn Hazard
This product contains a coin/button cell battery.
If the coin/button is swallowed,it can cause severe internal burns
in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely,stop using the
product and keep it away from children.
If you think batteries might have been swallowed or placed inside
any part of the body,seek immediate medical attention.
Thank you for purchasing this Emerson SmartSet Dual Alarm Clock Radio.
This clock uses Emerson's patented SmartSet Automatic Time Setting
System. The first time you connect this clock to your AC outlet, and
after every po wer interruption, within seconds the clock will automatically
set itself t o th e co r re c t Ye ar, M o n t h , D a t e , D a y, and Time. In addition,all
changes from Standard Time to Daylight Saving Time, and back to Standard
Time, are made automatically. There are dual alarms that can be set and used
independently, and both of the alarms can be programmed for everyday
operation, weekdays only, or weekends only. There is a long life lithium battery
installed in this clock when you buy it. This battery can maintain the time and
alarm settings for 1 to 2 years, or even longer. We have taken every precaution to
make sure this clock was in perfect working order when it left our factory.
If you encounter any problems with the set up or operation of this item, please
call the Emerson Consumer Products Corp.,Customer Service Hotline, toll free,
at 1 -800-898-9020.
®
®
2
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provi d e
rea s onabl e prote c tion a g ainst h armfu l interf erence in a res identi a l installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful in t erfer e nce to r adio
com m unica t ions. H oweve r, there i s no gu a rante e that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tur ning the eq uipment off and on,
the user is e ncouraged to try to co rrect th e interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.This device
complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment. This equipment
complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
The socket- outlet shall be installed near the equipment and shall be easily accessible.
Le socle de prise de courant doit être installé à proximité du matériel et doit être
aisément accessible.
l'appareil ne doit pas être exposé à des égouttements d'eau ou des éclaboussures et de plus
qu'aucun objet rempli de liquide tel que des vases ne doit être placé sur l'appareil.
lorsque la prise du RESEAU D'ALIMENTATION sur l'appareil est utilisée comme appareil de
déconnexion, cet appareil doit demeurer aisément accessible.
les batteries ne doivent pas être exposées à une chaleur excessive telle que celle du soleil, d'un
feu ou d'origine similaire.
Press the or button to adjust Year;
Setting the Year
Setting the Date
Setting the Time
6
7
To view the current zone number, press the
TIME ZONE button briefly and then release.
To change default time zone, press and hold
theTIME ZONE button, and then press or
button briefly until your desired time zone
appears on the display, then release all the buttons.
Note: Time zone and clock settings can only be adjusted in Standby
mode, where the function of Radio and Bluetooth are disabled (i.e.
indicator of MHz and BT are 'OFF').
the Clock
Checking the Current Year-Date-Day of Week-Time Settings
Press briefly the CLOCK SET button repeatedly to see the cycle of
year, date, day of week and time. To restore time display mode,
leave it idle for a few seconds.
the CLOCK SET button until the Year 'Flashes',
the button;
5
6
7
8
9
Press the CLOCK SET button again and release, the Date 'Flashes';
Press the or button to adjust the Minutes;
8
3
clock
clock
9
IMPORTANT: Alarm settings can be checked and adjusted in Standby mode
or even while Bluetooth, Radio or AUX mode is On.
15W Ultra Fast Wireles s Chargin g
SmartSet Clock Radio
with
Bluetooth, USB Charge Out, Dual
Alarm, LED Décor, Auto Dimmer
and 1.4” Cyan LED Display
(SmartSet
®
Patent No. 6,567,344)
OWNER’S MANUAL
ER100501
Visit our website at www.emersonradio.com
WARNING
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all
warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
11.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
12.) The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
13.) Mains plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from
the mains completely, the mains plug should be disconnected from the
mains socket outlet completely.
14.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
IMPORTANT SAFETY INSTRUCTIONS
PRÉCAUTION: Danger d’explosion si les piles sont remplacées de facon incorrect.
Remplacer les piles seulement par le méme type de pile ou
l’équivalent.
1
Th e ex cl ama ti on p oi nt w it hin
an eq u i lat e r al tr i a ngl e i s i n-
t e n d e d t o a l e r t t h e u s e r t o
t h e p r e s e n c e o f i m p o r t a n t
o p e r a t i n g a n d maintenance
( s e r v i c i n g ) i n s t r u c t i o n s i n
t h e l i t e r a t u r e a c c o m p a n y -
i n g t h e a p p l i a nc e .
The lightning flash with arrow-
head symb ol, withi n an equ i-
later al t riang le i s in tende d to
alert the user to the presence
of uninsulated 'dangerous voltage'
within the product's enclosure
t h a t m a y b e o f s u f f i c i e n t
magnitude to constitute a risk
of ele ct ric sh ock to per so ns.
WAR NIN G: TO R EDUCE THE RI SK OF
EL ECTRI C S HO OK D O N OT RE MO VE
COVER (OR BACK),NO USER SERVICEABLE
PA RT S I NS I DE R EF E R S E RV IC ING TO
QU ALIFI ED SE RVI CE PER SO NN EL.
AVIS:RISQU E DE CHOC
E L E C T R I Q U E - NE PA S O U V R I R
POUR ÉVITER TOUT DANGER DE CHOC ÉLECTRIQUE, NE PAS
RACCORDER AU SECTEUR TANT QUE LA GRILLE N'APAS ÉTÉ REMISE
EN PLACE.POUR RÉDUIRE LE RISQUE D’INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PAS EXPOSER CET APPAREIL SOUS LA PLUIE
ET L’HUMIDITÉ.
.
TO PREVENT ELECTRIC SHOCK HAZARD, DO NOT CONNECT TO MAINS
POWER SUPPLY WHILE GRILLE IS REMOVED.TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
Package Contents
ER100501
4
5
Watch Wireless
Charger Holder x 2
(2 different sizes)
12
13
14
15
16
17
23
22
21
20
19
24
25
26
28
18
27
REAR PANEL
29
33
32
®
IMPORTANT: The first time you connect your new SmartSet clock to
the AC outlet the internal computer will automatically set the time
correctly for the Eastern Time Zone, which is the initial default setting.
The display will scan for a few seconds and then show the correct Day
and Time in the Eastern zone. If you live in the Eastern Time zone,
there's nothing else to do. Your clock is set correctly and running. If you
do not live in the Eastern Time zone you must change the default zone
®
display to your own zone. You only do this one time and the SmartSet
will remember the new default time zone setting and will always
return to that setting after power interruption.
Press the or button to adjust the Month;
For example, April 16th will appear as '4.16';
Press the CLOCK SET button again and release,
the Hour 'Flashes';
Press the or button to adjust the Hour (where AM
indicator 'On' is AM, 'Off' is PM);
Press the CLOCK SET button again to store
all new settings and restore it to time display mode.
All Daylight Saving Time (DST) and Leap Year adjustment are made
®
automatically by the SmartSet internal computer as follows:
Turn Daylight Saving Function Off / On:
Daylight Saving Time is NOT observed in Hawaii, American Samoa, Guam,
Puerto Rico, the Virgin Islands and in, most of Arizona, with exception of the
Navajo Indian Reservation in Arizona.
If you do not want the clock to adjust itself automatically according to Daylight
Saving Time, you can disable it by pressing and holding the FM MEM. button
for 5 secs, the display will show DST start date of current year , which means
the auto Daylight Saving Time is enabled ('On' by default). Press either the
or button to toggle this DST start date between 'OFF' and 'On'. Press the
FM MEM. button again to display the DST end date of current year, which can
be disabled by pressing either the or button to toggle this DST end date
between 'OFF' and 'On'. Press the FM MEM. button briefly or leave it idle for
5 secs to save the new settings and resume to clock mode.
Your clock radio has two separate alarms Alarm1 (AL1) and Alarm2 (AL2) that can be set
and used independently. You may use the alarms to wake two persons at different times,
or you may use one alarm for weekdays and the other one for weekends. Please ensure that
you have set the wake up time and alarm week mode correctly.
Adjusting the Wake Up Time and Alarm Volume for Buzzer/Radio Alarm
The procedure for adjusting the wake up time is the same for both Alarm1 and Alarm2.
• Press and hold either the AL1 or AL2 button until the display blinks and change from the
current time to the Alarm1 or Alarm2 wake up time.
• Release the AL1 (AL2) button, press the or button to adjust Hour, press the or
button to adjust Minutes.
• Press the AL1 (AL2) button again to adjust Alarm Volume V01-V15 by pressing the VOL-
or VOL+ button.
• Press the TUNE+ or TUNE- button repeatedly to adjust Alarm Week Mode if necessary.
• Press the AL1 (AL2) button again to store the alarm setting.
Note: Be sure that you have set the wake up time correctly by observing the
AM indicator. If the AM indicator is 'On' the wake up time is “AM”. If it is 'OFF',
the wake up time is “PM”.
4
5
6
7
8
9
10
11
Wireless Charging
Indicator
BT Indicator ('Solid'=Bluetooth
connected)
SLEEP/TIME ZONE Button
CLOCK SET Button
BT ON/OFF Button
LOW BATTERY Indicator
MHz FM Radio Indicator
30
DOWN/VOL-/SNOOZE Button
Ultra Fast Wireless Charging
Pad
FM ON/OFF Button
DIMMER Button
LED Button Décor
FM STO.(STORE) / BT Button
FM MEM.(MEMORY) / BT PAIR
Button
TUNE+ Button
UP/VOL+ Button
TUNE- Button
Adapter Cable
AC Adapter
USB Type A Charging Port
1
2
3
Backup Battery Holder
FM Antenna Wire
Remove any descriptive labels or stickers on the front or top of the cabinet,
if any.
Do not remove any labels or stickers from the back or button of the cabinet.
Note the serial number on the bottom of your clock and write this number
in the space provided on the Warranty page of this manual.
Place your clock on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
Unwind the antenna wire and extend it fully.
SLP
SLP Sleep Indicator
31
Wireless Charging Earbuds Pad
USB Type C Charging Port
USB OUTPUT
5V 2.1A
ANT.