Owner's Manual

ManualsBrandsEmerson Manualsalarm clocksAlarm Clock Radio with Bluetooth and Wireless Chargers

Table Of Contents

ER100501-20220314-00

Charging the Watch

Press the DIMMER button while in standby mode to select any of the three

levels.To use Automatic Dimmer function, press the DIMMER button

repeatedly until it displays 'AU'. It will then automatically adapt clock

display brightness based on ambient lighting conditions to make display

appear consistent in diﬀerent environments without the need of pressing the

DIMMER button manually. It also can be adjusted when the Bluetooth or

Radio is On.

This clock radio has two USB(Type A/ Type C) port at the back, which can

provide up to 5V 2.1A to charge devices like smartphone, tablet etc.

via a USB cable (not provided).

Note: Electrical energy drawn from the

USB port may vary due to diﬀerent

charging cable condition, battery

characteristic or power

management system of your

device being charged.

2-Level LED Décor

Press the LED button to turn the night LED ON(high/low level) or OFF when needed.

Auto Dimmer and 3-Level Dimmer Control

The lithium backup battery needs replacement when the LOW BATTERY

indicator ﬂashes, otherwise, the time and alarm settings will be lost/reset

after a power outage.

• Leave the AC adapter connected to your AC outlet to retain memory while

the original battery is removed.

• Unscrew the battery holder from the cabinet with a small screwdriver and

insert a new battery with the same CR2032 or equivalent type into the

holder the same way, observing the positive (+) polarity before sliding the

holder back into the slot. The LOW BATTERY indicator should then be Oﬀ.

polarity facing downward

ER100501

This device complies with Industry Canada Licence-exempt RSSs. Operation

is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC Information

Checking the Wake Up Time and Alarm Week Mode

Snooze Alarm

When the alarm comes On, press the SNOOZE button to

pause it for 9 minutes. Alarm indicator will ﬂash during

Snooze Alarm mode. To turn oﬀ Snooze Alarm, press either

the AL1 or AL2 button once.

Note:If not turned oﬀ, the Snooze Alarm will only be active

for one hour.After Snooze Alarm turned Oﬀ, the alarm will

come On again same time next day (depends on your Alarm Week Mode

setting).

Activating and Deactivating the Alarm

· Press the AL1 or AL2 button repeatedly to select your desired Alarm

Mode: Wake to Radio, Wake to Buzzer, or Oﬀ.

· When the `1♫/2♫' indicator glows, the wake up to Radio alarm will be On.

· When the `1 /2 ' indicator glows, the wake up to Buzzer alarm will be On.

· To completely turn Oﬀ the alarm, press the AL1 or AL2 button

repeatedly until the Radio `1♫/2♫' indicator or the Buzzer `1 /2 ' indicator

is Oﬀ.

Selecting the Alarm Week Mode

Your SmartSet clock radio allows you to select from three diﬀerent alarm

week modes for each alarm. The Alarm Week Modes are:

• Everyday - the alarm will turn on all 7 days

• Weekdays only - the alarm will only turn on Monday

through Friday

• Weekends only - the alarm will only turn on Saturday

and Sunday

• If all 7 indicators are 'On', the Everyday mode is selected.

• If only the MON (Monday) through FRI (Friday) indicators are

'On', the Weekdays only mode is selected.

• If only the SAT (Saturday) and SUN (Sunday) indicators are

'On', the Weekends only mode is selected.

Press and hold the AL1(AL2) button until the display blinks and shows the

wake up time. Release the AL1(AL2) button and then press it again to show

the alarm volume and alarm week mode settings. Press the AL1(AL2) button

to resume to clock mode.

The procedure for setting the alarm volume for Wake-To-Radio is the same

for both Alarm 1 and Alarm 2.

* Press the FM button to turn the FM Radio mode On.

* Tune in or recall from Memory the station that you wish hear when the

alarm comes On.

* Follow the above procedure in section 9 for setting the wakeup time and

alarm volume.

* Turn the unit Oﬀ.The unit will go to Standby mode.

reconnection between them. Then, set this unit to Bluetooth mode, and tap the

Bluetooth switch on your phone/device Oﬀ and back On again to refresh/search

any nearby ER100501 for pairing.

Listening to FM Radio

• Extend the antenna wire fully and orient it for better FM reception.

• Press the FM button until the MHz indicator turns 'On', and the FM station

frequency displays.

• Set the VOLUME by pressing the VOL + or VOL - button to a level that suits

your needs.

• When you ﬁnish listening to radio, press the FM button to turn the radio Oﬀ.

The MHz indicator will then turn 'Oﬀ'.

Receive your desired station with the TUNING control:

• Press the TUNE + / TUNE - button brieﬂy, the receiving

frequency will increase / decrease by one step.

• Press and hold the TUNE + / TUNE - button for

2 seconds then release, Auto Station Seeking will be

engaged, the receiving frequency will increase / decrease

automatically until a station with acceptable reception is found.

Storing and Recalling Radio Station Memory Manually

When you have a few favorite radio stations to listen to, you may like to save

them in speciﬁc memory locations and pick one of them in a few seconds

without the need of searching it each time. Our digital tuning technology allows

you to do this easily by following the steps listed below:

Storing Station to the Memory

• Turn the unit On and select Radio mode (MHz indicator 'On').

• Tune in the desired station by the TUNING control as described.

• Press and hold the FM STO. button (for 2 seconds) until 'P XX' blinks,

indicating the memory location to store the station currently tuned in.

• While 'P XX' is blinking, press the TUNE + or TUNE - button can change the

memory location from 1 through 20. For example, 'P 03' means the current

listening station is about to be stored into the 3rd location of the memory.

• After deciding the memory location, press the FM STO. button again, the

currently listening station is then stored accordingly.

• The display will show the frequency of the station, and after a few seconds, it

will restore the current time.

Recalling Station from the Memory

• Turn the Radio mode On.

• Press the FM MEM. button, 'P XX' shows on the display, and the station

according to the memory location will then be tuned in.

• Repeatedly pressing the FM MEM. button or the TUNE + / TUNE - button will

change the memory location from 1 through 20, and the station stored in the

location will then be tuned in once the memory location is selected and all

buttons released.

• The display will show the frequency of the station, and then returns to the

current time after a few seconds.

Listening to FM Radio

Note: During Wireless charging, FM radio will be muted until the device on the

charging pad is removed. Please use wired USB charging while listening to

radio when necessary.