Installation Guide

11.Position the cup/light fixture (1)(7) on
the cover plate (2) and install the
three screws (3) that were previously
removed in step 2 and tighten
securely.
12.Proceed to “Installation of Glass
Shades/Globes” section.
Installation on Emerson
Fans Having Two-Piece
Die-Cast Switch Housings
1.Remove all parts and parts packages
from carton.
2.Remove the cover (5) from the fan
switch housing (1) by removing the two
outer screws (2). (See Figure 4.)
3.Remove the center screw (4) in the
switch housing cover (5). Insert the
black and white wires from the light
fixture (6) thru the hole and thread the
switch housing cover tightly onto the
light fixture. (See Figure 4.)
(3) WIRE
CONNECTORS
WHITE WIRES
BLUE WIRE
BLACK WIRE
FAN
SWITCH
CHAIN
(1) SWITCH
HOUSING
ASSEMBLY
(5) COVER
(2) SCREWS
(4) CENTER
SCREW
(8) LOCKWASHER
(7) HEX NUT
(6) LIGHT
FIXTURE
Figure 4
Assembly and Installation
2 3
Installation on Emerson
Fans Having A Modular
Switch Cup with Center
Screw
1.Remove all parts and parts packages
from the carton.
2.Remove the switch cup (1) from the
cover plate (2) by removing the three
screws (3) around the side of the switch
cup (Figure 1).
3.Disconnect the motor connector (4)
from the switch cup connector (5)
(Figure 1).
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions
carefully.
1. Read your Owner's Manual carefully before installing the light fixture. Retain Owner's
Manual for future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Before installing or servicing the light fixture or ceiling fan, switch power off at
service panel and lock service panel disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a warning device, such as a tag, to the service panel.
3. Use intermediate base bulbs of the wattage indicated on the fixture. Do not exceed
the indicated wattage.
4. Do not use as a ceiling fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock be sure electricity is turned off at the main fuse or
circuit breaker box before wiring.
2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to national and local electrical codes.
4. Follow the recommended instructions for the proper method of wiring your new light
fixture. If you feel you do not have enough electrical wiring knowledge or experience,
have your light fixture installed by a licensed electrician. Any electrical work not
described in this manual should be performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on
Emerson “CF” and “F” Series Ceiling Fans. This light kit is not to be used with CF652,
CF653, CF670, and CF742 Model Ceiling Fans installed in damp or wet locations.
4.Remove the center screw (6) from the
switch cup (Figure 1).
5.Carefully locate the white and blue
wires (labeled either "L" or "LIGHT") in
the switch cup and remove the wire
connectors from the wires.
6.Insert the black and white wires from
the light fixture (7) through the center
hole in the switch cup (Figure 2) and
thread the switch cup onto the light
fitter. Hold wires taut while installing
switch cup to prevent the wires from
twisting. Tighten the fitter until the fan
switch chain aligns with the bushing in
side of fitter.
7.Insert the black and white wires through
the lockwasher (8) and the hex nut (9)
supplied. Firmly tighten the hex nut to
secure the light fixture to the switch
cup.
8.Connect the white wire from the switch
cup to the white wire of the light fixture
(Figure 2). Connect the blue wire from
the switch cup to the black wire of the
light fixture. Use listed wire connectors
(previously removed in step 5) to make
connections (Figures 2 and 3).
9.Carefully tuck all wires and splices into
the switch cup (1). (Figure 2.)
10. Connect the motor connector (4) to
the switch cup connector (5).
(3) SCREWS
(6) CENTER SCREW
(1) SWITCH
CUP
(4) MOTOR
CONNECTOR
(2) COVER
PLATE
(5) SWITCH CUP
CONNECTOR
Figure 1
(3) SCREWS
(5) SWITCH CUP
CONNECTOR
(2) COVER PLATE
(6) WIRE
CONNECTORS
WHITE WIRES
(1) SWITCH
CUP
BLACK WIRE
FAN SWITCH
CHAIN
(8)
LOCKWASHER
(9) HEX NUT
(7) LIGHT FIXTURE
BLUE WIRE
(4) MOTOR
CONNECTOR
Figure 2
Figure 3
WARNING: To avoid possible fire or
electrical shock, make certain no
bare wire strands are exposed
outside wire connectors.
NOTE: YOUR FIXTURE MAY NOT LOOK THE SAME AS THE ONE IN THIS
ILLUSTRATION. HOWEVER, IT INSTALLS IN A SIMILAR MANNER.
NOTE: YOUR FIXTURE MAY NOT LOOK THE SAME
AS THE ONE IN THIS ILLUSTRATION. HOWEVER,
IT INSTALLS IN A SIMILAR MANNER.
Do not install or use the light fixture
if any part is missing or damaged.
Call toll-free:
1-800-654-3545
WARNING
!
To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.
WARNING
!
To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before wiring.
WARNING
!
To avoid possible electrical shock,
be careful not to pinch wires
between the switch cup (1) and the
cover plate (2)
WARNING
!
WARNING
!