Instruction manual

ManualsBrandsEmerson Manualscomputer componentsFIELDVUEDVC6200p

www.Fisher.com

Fisher

FIELDVUE

™

DVC6200p Digital Valve

Controller Device Setup and Accessing

Communication and Calibration using Siemens

SIMATIC Manager/PDM

Contents

Related Documents 2...........................

Connecting the Digital Valve Controller using

Enhanced Device Description (EDD) for Siemens

SIMATIC PDM 3................................

Setting PG/PC Interface 4.......................

Loading the DVC6200p EDD to the SIMATIC

Manager/PDM Catalog 8.....................

Device Setup using Siemens PDM Software 11.....

Going Online with the DVC6200p 17..............

Performing One-Step Local Quick Setup

to Calibrate and Tune the DVC6200p 19........

This document takes you through setting up and accessing the DVC6200p using Siemens SIMATIC PDM software, as

well as performing initial actuator and valve configuration, calibration, and tuning using the Guided Setup procedure.

The procedures covered in this supplement were completed using Siemens SIMATIC Manager/PDM 8.1. While the

steps taken should remain basically the same, screens may vary slightly if you are using a different version of the

software.

Ensure that all necessary files, including the latest DVC6200p EDD, are available.

Note

Setting PG/PC Interface and loading the DVC6200p EDD are generally required only once per computer.

Refer to the DVC6200 Series Quick Start Guide (D103556X012) for DVC6200p

installation, connection and initial configuration information. If a copy of this quick

start guide is needed scan or click the QR code at the right, contact your Emerson

Process Management sales office, or visit our website at www.Fisher.com.

Instruction Manual Supplement

D103560X012

DVC6200p Digital Valve Controller

November 2014

Scan or click

to access

field support

Summary of content (20 pages)

PAGE 1
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Fisherr FIELDVUE™ DVC6200p Digital Valve Controller Device Setup and Accessing Communication and Calibration using Siemens SIMATIC Manager/PDM Contents Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Connecting the Digital Valve Controller using Enhanced Device Description (EDD) for Siemens SIMATIC PDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
DVC6200p Digital Valve Controller Instruction Manual Supplement November 2014 Related Documents D Fisher FIELDVUE DVC6200 Series Digital Valve Controller quick start guide (D103556X012) D Fisher FIELDVUE DVC6200p Digital Valve Controller instruction manual (pending) All documents are available from your Emerson Process Management sales office. Also visit our website at www.FIELDVUE.com.
PAGE 3
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Connecting the DVC6200p using Enhanced Device Description (EDD) for Siemens SIMATIC PDM Refer to figure 1. Figure 1.
PAGE 4
DVC6200p Digital Valve Controller November 2014 Instruction Manual Supplement D103560X012 Setting PG/PC Interface Note Setting the PG/PC interface or PC card (CP 5711 or similar PROFIBUS card) is done only once, after the first hardware installation of the PC card inside the computer. 1. Set PG/PC Interface is available under the PC ‘Control Panel’ once Siemens STEP 7 or SIMATIC Manager/PDM software is installed. a. Go to Set PG/PC Interface as shown in figure 2. b. Under the Interface, click on Select..
PAGE 5
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 2. If the PROFIBUS card is the only master on the bus select 'PG/PC is the only master on the bus', as shown in figure 3. If there are other Class 1 or Class 2 masters on the bus, then DO NOT select PG/PC is the only master on the bus. Under Network Parameters select the appropriate Transmission Rate of the bus. Click OK when all parameters are set. Figure 3.
PAGE 6
DVC6200p Digital Valve Controller November 2014 Instruction Manual Supplement D103560X012 3. Click on Diagnostics... as shown in figure 4. Figure 4. Diagnostics... 4. In the Diagnostics window, shown in figure 5, click on Test to check the status of the PROFIBUS card and network. Figure 5.
PAGE 7
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 5. Confirm the status is OK (see figure 6.) If the status is Failed, changes to the parameters set in step 2 may be required. Note If the“Test” fails, check the DP/PA coupler type used and the parameter setting, as recommended by the coupler manufacturer. 6. To identify the address of the host and any connected device select Read as shown in figure 6. Figure 6. Status/Network Diagnostics TEST STATUS READ 7.
PAGE 8
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Figure 7. Status/Network Diagnostics—Station Address STATION ADDRESS BUS NODE 55 Note The default address of the DVC6200p is set by the factory to 126. Note In the above example, a slave device was found at Bus Node 55, and the Class 2 Master device is at address 4. Make note of the addresses found during the bus node scan for future reference.
PAGE 9
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Figure 8.
PAGE 10
DVC6200p Digital Valve Controller Instruction Manual Supplement D103560X012 November 2014 Note Loading the EDD for a specific device, such as the DVC6200p, on the SIMATIC PDM on a station is only needed once, unless a new or updated EDD is required. Figure 9.
PAGE 11
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Device Setup using Siemens SIMATIC PDM Software Before beginning Device Setup, be sure the instrument is correctly mounted and all pneumatic and electrical connections are made. Refer to the quick start guide for general mounting guidelines or the installation instructions supplied with the mounting kit. Pneumatic and electrical connection information can also be found in the the quick start guide.
PAGE 12
DVC6200p Digital Valve Controller November 2014 Instruction Manual Supplement D103560X012 2. Right click on the project in the left hand pane, select Insert New Object > networks (if not already available). Figure 11. Adding Networks PROJECT NAME 3. Right click on the networks icon in the right pane and select Insert New Object > Communications Network as shown in figure 12. Figure 12.
PAGE 13
Instruction Manual Supplement D103560X012 DVC6200p Digital Valve Controller November 2014 4. Enter the Object name then click on Assign Device Type as shown below. Navigate to PROFIBUS DP network and select OK. Figure 13.
PAGE 14
DVC6200p Digital Valve Controller November 2014 Instruction Manual Supplement D103560X012 5. A new network now appears on the right pane, as shown in figure 14. Right-click on the network and select Insert New Object > Object. Figure 14.
PAGE 15
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 6. Enter the Object name (for example, the tag name) and define the PROFIBUS address. Click on Assign Device Type. Select PA Standalone for standalone station PDM or PA Step7 when PDM is in an integrated environment. Click OK. Click OK in the resulting screen. Note The default address of the DVC6200p is set by the factory to 126. This may need to be changed depending on plant requirements. Figure 15.
PAGE 16
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 7. Right click on the device in the right pane and select Open Object, as shown in figure 16. Figure 16. Open Device in SIMATIC PDM 8. In the resulting Offline menu screen (shown in figure 17), select the Upload icon, as indicated below, to upload the device to the database. Click Start. The upload is complete when the tag name appears. Close the Upload PG/PC dialog screen.
PAGE 17
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Going Online with the DVC6200p 1. Click on Device > Online to access to open the DVC6200p EDD, as shown in figure 18. Figure 18.
PAGE 18
Instruction Manual Supplement DVC6200p Digital Valve Controller D103560X012 November 2014 Refer to figure 19 to view the Overview screen interface. Overview shows the Primary Purpose Variables and the Device Status and Mode. It also allows you to enter the Device Serial Number and access Device Information, Stroke Valve, and Calibration procedures. Figure 19. FIELDVUE DVC6200 EDD Overview DEVICE STATUS—CLICK TO SEE ACTIVE STATUS ALERTS CHANGE MODE HERE 2.
PAGE 19
Instruction Manual Supplement D103560X012 DVC6200p Digital Valve Controller November 2014 Note Auto-calibration and tuning are part of the Device Setup procedure. However, if the DVC6200p is not physically connected to an actuator/valve assembly you will not be able to perform the auto-calibration/tuning procedures. If Device Setup is being done prior to mounting the device complete Device Setup up to auto-calibration and select Cancel, as shown in figure 21.
PAGE 20
DVC6200p Digital Valve Controller November 2014 Instruction Manual Supplement D103560X012 Travel calibration and auto tuning can be accomplished by shorting the auxiliary terminal connections, shown in figure 22, between 3 to 10 seconds. You can abort the procedure by shorting the auxiliary terminals for 1 second. Pressure range will also be captured during this procedure. Figure 22.