Data Sheet

ManualsBrandsEmerson ManualsValve InstrumentationEmerson Fisher ValveLink Software

www.Fisher.com

ValveLinkt Software

ValveLinkt Solo

AMS ValveLinkt SNAP‐ONt

ValveLinkt DTM

ValveLinkt PLUG‐IN for PRMr

H Communicate with both HARTr and

OUNDATIONt fieldbus FIELDVUEt digital valve

controllers

H Configure, calibrate, and diagnose FIELDVUE

instruments from one location

H Use the Performance Tuner to easily optimize

tuning

H Performance Diagnostics provide in‐service

diagnostics for monitoring the health of the

valve assembly without disturbing the process

H Diagnostics provide validation of assembly

rebuild and detailed insight into the physical

condition of the valve/actuator assembly

H Setup and test FIELDVUE instruments for Safety

Instrumented System (SIS) Solutions

H Scheduler allows you to specify a time and date

to automatically run tasks on a regular basis

H Save time by preconfiguring calibration and

diagnostics in the shop with Batch Runner

ValveLink Software

D102227X012

Product Bulletin

62.1:ValveLink Software

October 2012

Summary of content (12 pages)

PAGE 1
ValveLink Software D102227X012 Product Bulletin 62.
PAGE 2
Product Bulletin ValveLink Software 62.1:ValveLink Software October 2012 D102227X012 ValveLink Software Product Suite ValveLink software is available in a variety of configurations to allow you to realize the full benefit of FIELDVUE digital valve controllers. ValveLink Solo ValveLink Solo permits users to perform configuration, calibration, and diagnostics on HART and FOUNDATION Fieldbus FIELDVUE digital valve controllers.
PAGE 3
ValveLink Software D102227X012 Product Bulletin 62.1:ValveLink Software October 2012 Communicate with both HART and FOUNDATION fieldbus FIELDVUE digital valve controllers ValveLink software remotely communicates with HART FIELDVUE instruments over the existing 4‐20 mA signal wiring using the HART communication standard. The same software also can communicate with FOUNDATION fieldbus FIELDVUE instruments over the fieldbus H1 segment.
PAGE 4
Product Bulletin 62.1:ValveLink Software October 2012 ValveLink Software D102227X012 Use the Performance Tuner to easily optimize tuning The Performance Tuner lets you easily adjust a FIELDVUE digital valve controller for optimum performance. When mounting a FIELDVUE digital valve controller, to either a Fisher or a non‐Fisher valve, the Performance Tuner can optimize valve performance for you.
PAGE 5
ValveLink Software D102227X012 Product Bulletin 62.1:ValveLink Software October 2012 Provide Real‐Time Notification of Current and Potential Valve and Instrument Problems using Performance Diagnostics Performance Diagnostics enables the use of diagnostics while the valve is in‐service and operating.
PAGE 6
Product Bulletin ValveLink Software 62.1:ValveLink Software October 2012 D102227X012 Provide validation of assembly rebuild and detailed insight into the physical condition of the valve/actuator assembly Performance Diagnostics vary the digital valve controller set point and plot valve operation to provide insight into the dynamic performance of the valve/actuator assembly.
PAGE 7
ValveLink Software D102227X012 Product Bulletin 62.1:ValveLink Software October 2012 The Step Response diagnostic allows you to evaluate how well the valve tracks an input change. By minimizing dead time, deadband, and overshoot, process control is greatly enhanced. With the Step Response test you can: H Validate tuning parameters. H Obtain a numerical analysis for overshoot, hysteresis, dead time, t63, and t86. H Define up to 30 steps. A performance step test provides a predefined sequence of 25 steps.
PAGE 8
Product Bulletin 62.1:ValveLink Software October 2012 ValveLink Software D102227X012 H A Signature Analyzer to automate diagnostics results of Valve Signature and Partial Stroke diagnostic data. The Signature Analyzer uses a set of user configurable limits to help determine possible issues with the valve assembly, such as a broken shaft or stem. H A Trigger event that allows you to log the “Safety Demand” event while storing pre‐event and post‐event data.
PAGE 9
ValveLink Software D102227X012 Product Bulletin 62.1:ValveLink Software October 2012 Scheduler allows you to specify a time and date to automatically run tasks on a regular basis With Scheduler, you can schedule tasks, such as in‐service Performance Diagnostics and SIS Partial Stroke diagnostics to run on a recurring daily, weekly, monthly, or yearly schedule that you specify.
PAGE 10
Product Bulletin 62.
PAGE 11
Product Bulletin ValveLink Software 62.1:ValveLink Software October 2012 D102227X012 Table 1.
PAGE 12
Product Bulletin 62.1:ValveLink Software October 2012 ValveLink Software D102227X012 Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.