Specifications

ManualsBrandsEmerson ManualsBeverage DispenserH-770

The Installation, Care and Use of Your New

Steamin' Hot

Models H-770 and H-778

Hot Water Dispenser

Safety Instructions

Warnings alert you to hazards or unsafe practices which could result in severe

personal injury or death.

Cautions alert you to hazards or unsafe practices which could result in minor personal injury

or product/property damage.

Please be certain that the person who installs or uses this appliance carefully reads and understands the Safety Instructions

contained in this manual. This appliance produces extremely hot water. Do not allow children to operate this appliance.

How your hot water

dispenser works

Water is electrically heated to a brewing/cooking hot 190°F

(88° C)* by a compact tank that mounts under the sink. A

thermostat maintains it at this approximate temperature.

When you turn the tap, cold water enters the bottom of the

tank and forces hot water out of the faucet. The system is

vented so the tank is not pressurized.

*APPROXIMATE

Important

Do not install this appliance in public areas where there

is unsupervised access to this appliance.

Summary of content (8 pages)

PAGE 1
The Installation, Care and Use of Your New Steamin' Hot Models H-770 and H-778 Hot Water Dispenser Safety Instructions Warnings alert you to hazards or unsafe practices which could result in severe personal injury or death. Cautions alert you to hazards or unsafe practices which could result in minor personal injury or product/property damage. Please be certain that the person who installs or uses this appliance carefully reads and understands the Safety Instructions contained in this manual.
PAGE 2
What Should You Know Before You Begin Connecting the dispenser to your regular water supply requires no special plumbing. All details are covered in the installation instructions. Be sure that all plumbing connections conform to your applicable local codes. If your water supply contains sand, grit or other suspended particles, the use of a filter is recommended. The filter should not result in the water pressure to the dispenser dropping below 20 pounds per square inch (138kPa).
PAGE 3
FIRST, LET'S REMOVE YOUR EXISTING OK... Let's get on with the installation 1 A If you have a spray unit like this one on your B A nut connects the spray hose to a tube at the kitchen sink, the hole is perfect for mounting your Hot Water Dispenser's head. bottom of your faucet. FIRST, BE SURE FAUCET IS TURNED OFF. Then remove this nut. RINSE SPRAY AND HOSE What if you don't use a sprayer hole? C Now pull the spray head and hose entirely out D Next, remove the nut from the bottom of the Of the hole.
PAGE 4
LET'S MAKE THE WATER CONNECTION Connect to the cold water supply line The recommended connection can be made using a shutoff valve. This is a more complex installation and should only be attempted by an experienced installer with the proper knowledge and tools. CAUTION Product Damage • Do not use paste -type pipe sealants on water line connec tions. Doing so may result in clogging of water passages. Where plumbing codes permit, a saddle valve (not supplied) can be used to supply water to the dispenser.
PAGE 5
NOW, LET'S MOUNT THE TANK 7 C Hang the tank on the bracket. There is room to adjust the bracket, if necessary. A Mount the tank on either a back B Position the metal mounting or side wall. Start by holding tank up and making sure the tubes reach it. When you have decided where you want to mount the tank, mark the position of the top of the tank on the wall with a pencil. Allow sufficient space for drain screw access.
PAGE 6
FILL THE TANK...IT'S READY 9 A Make sure the water supply B After about one minute, the valve is turned on. Then turn the dispenser knob and hold it open. tank will fill and water will begin coming out of the faucet. Turn off the faucet and check all connections for leaks. DO NOT PLUG IN YET! WARNING Fire/Product Damage Do not remove or alter the thermal safety fuse.
PAGE 7
Specifications Model H-778 Commercial Model only: This model comes with a 4" chrome extension sleeve for the tap. To attach, slide the sleeve up and over the copper tubes and insert it into the bottom of the tap assembly as shown. (No gasket is provided). Then follow step 3 to attach to sink, using longer screw provided. Sink or Counter This unit is designed to be installed in sinks or countertops of 3/4" (1.9 cm) thickness or less. For any surface thicker than this, obtain a longer #10-24 mounting screw.
PAGE 8
Service/Maintenance Instructions Adjusting Temperature What if water is dripping from the spout? If water drips from the spout, draw 2 or 3 cupfuls while unit is heating. This will drain any water out of the unit's expansion chamber. If water still drips prior to the automatic thermostat shutting off (you can hear it), turn thermostat to a slightly lower temperature setting. See thermostat adjustment procedure at left.