Liebert GXT MT+
Table of Contents 1. Important Safety Warning……………………………………………… 1-1. Transportation 1-2. Preparation 1-3. Installation 1-4. Operation 1-5. Maintenance, service and faults 1 1 1 1 1 2 2. Installation and setup…………………………………………………… 2-1. Rear view 2-2. Setup the UPS 3 3 3 3. Operations Instruction…………………………………………………. 3-1. Button operation 3-2. LCD Panel 3-3. Audible Alarm 3-4. LCD display wordings index 3-5. UPS Setting 3-6. Operating Mode Description 3-7. Faults Reference Code 3-8.
1. Important Safety Warning Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and read carefully the following instructions before installing the unit. Do not operate this unit before reading through all safety information and operating instructions carefully 1-1. Transportation z Please transport the UPS system only in the original package to protect against shock and impact. 1-2.
1-5. Maintenance, service and faults z The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified maintenance personnel. z Caution - risk of electric shock. Even after the unit is disconnected from the mains (building wiring outlet), components inside the UPS system are still connected to the battery and electrically live and dangerous.
2. Installation and Setup NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. Please keep the original package in a safe place for future use. NOTE: There are two different types of online UPS: standard and long-run models. Please refer to the following model table. Model 1000 2000 3000 Type Model 1000L 2000L 3000L Standard Type Long-run 2-1. Rear View 1000(L) TOWER 2000(L) TOWER 3000(L) TOWER 1. Programmable outlets: connect to non-critical 7.
Step 2: UPS output connection There two kinds of outputs: programmable outlets and general outlets. Please connect non-critical devices to the programmable outlets and critical devices to the general outlets. During power failure, you may extend the backup time to critical devices by setting shorter backup time for non-critical devices.
Step 7: Install software For optimal computer system protection, install UPS monitoring software to fully configure UPS shutdown. You may insert provided CD into CD-ROM to install the monitoring software. If not, please follow steps below to download and install monitoring software from the internet: 1. Go to the website http://www.power-software-download.com 2. Click ViewPower software icon and then choose your required OS to download the software. 3.
3. Operating Instruction 3-1. Button operation Button View Button Function ¾ Turn on the UPS: Press and hold ON/MUTE button for at least 2 seconds to turn on the UPS. ¾ Mute the alarm: When the UPS is on battery mode, press and hold this button for at least 5 seconds to disable or enable the alarm system. But it’s not applied to the situations when warnings or errors occur. ON/MUTE Button ¾ Up key: Press this button to display previous selection in UPS setting mode.
3-2. LCD Display Display Function Backup time setting and information Indicates the backup time in pie chart. Indicates the backup time in numbers. H: hours, M: minute, S: second Setting operation Indicates the setting operation. Fault & warning information Indicates that the warning situation occurs. Indicates the warning and fault codes, and the codes are listed in details in 3-5 section. Mute operation Indicates that the UPS alarm is disabled.
Indicates the UPS is in battery mode. Indicates the UPS is bypass mode. Indicates the UPS is in ECO mode. Indicates the UPS is in converter mode. Indicates the UPS is charging battery. Battery information Indicates the Battery capacity by 0-25%, 26-50%, 51-75%, and 76-100%. Indicates the battery is fault. Indicates low battery level and low battery voltage. 3-3.
3-5. UPS Setting Parameter 1 Parameter 2 There are two parameters to set up the UPS. Parameter 1: It’s for program alternatives. There are 8 programs to set up. Refer to below table. Parameter 2 is the setting option or value for each program.
z 04: ECO enable/disable Interface Setting Parameter 2: Enable or disable ECO function. You may choose the following two options: ENA: ECO mode enable DIS: ECO mode disable z 05: Bypass enable/disable when UPS is off Interface Setting Parameter 2: Enable or disable Bypass function when UPS is off. You may choose the following two options: ENA: Bypass enable DIS: Bypass disable z 06: Programmable outlets enable/disable Interface Setting Parameter 3: Enable or disable programmable outlets.
3-6. Operating Mode Description Operating Description mode Switch on When pressing “ON/MUTE” button, if battery voltage is within acceptable range, “ON” will flash until the UPS is turned on. Online mode When the input voltage is within acceptable range, UPS will provide pure and stable AC power to output. The UPS will also charge the battery at online mode. ECO mode Energy saving mode: When the input voltage is within voltage regulation range, UPS will bypass voltage to output for energy saving.
Fault mode The UPS is in fault mode when no output power is supplied from the UPS and the fault icon flashes on the LCD display, although the information of UPS can be displayed in the screen. 3-7.
4. Troubleshooting If the UPS system does not operate correctly, please solve the problem by using the table below. Symptom Possible cause Remedy No indication and alarm even The AC input power is not Check if input power cord though the mains is normal. connected well. firmly connected to the mains. The AC input is connected to Plug AC input power cord to the UPS output. AC input correctly. The icon and the warning code EPO function is activated.
Fault code is shown as 14 and the icon is lighting on LCD display and alarm is continuously sounding. Fault code is shown as 1, 2, 3, 4, 11, 12, 13 and 41 on LCD display and alarm is continuously sounding. Battery backup time is shorter than nominal value The UPS shut down automatically because short circuit occurs on the UPS output. A UPS internal fault has occurred. There are two possible results: 1. The load is still supplied, but directly from AC power via bypass. 2.
5. Storage and Maintenance 5-1. Operation The UPS system contains no user-serviceable parts. If the battery service life (3~5 years at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case, please contact your dealer. Be sure to deliver the spent battery to a recycling facility or ship it to your dealer in the replacement battery packing material. Storage Before storing, charge the UPS 5 hours. Store the UPS covered and upright in a cool, dry location.
6. Specifications CAPACITY* INPUT Low Line Transfer Voltage Range Low Line Comeback High Line Transfer High Line Comeback Frequency Range Phase Power Factor OUTPUT Output voltage AC Voltage Regulation Frequency Range Frequency Range (Batt. Mode) Overload Current Crest Ratio Harmonic Distortion Transfer AC Mode to Batt. Mode Time Inverter to Bypass Waveform (Batt.
Runtime Chart: Model Load Level 25% 50% 75% 100% 1000 30 15 8 5 2000 24 18 10 6 3000 31 13 8 5 NOTE: All run times are in minutes, assume fully charged batteries and are typical at 77°F (22°C).
AP10DPG-GXTMT+V1-UM