EM4591 Universal Wi-Fi repeater with WPS
| ENGLISH EM4591 – Universal Wi-Fi repeater with WPS Table of contents 1.0 Introduction ...........................................................................................................2 1.1 Packing contents ...............................................................................................2 1.2 Device Overview................................................................................................3 2.0 Where to place the EM4591 repeater? .....................................
| ENGLISH 1.2 Device Overview Front Panel LABEL LED Signal strength 3 BARS 2 BARS 1 BAR STATE DESCRIPTION Connected Connected Connected 90% and above (Excellent) 55-89% (Recommended) 10-54% (Weak) Top Panel LABEL WPS Button DESCRIPTION Connect EM4591 to any WPS capable devices (5 sec. to connect to router/AP or 2 sec.
| ENGLISH Bottom Panel LABEL DESCRIPTION RESET If the signal indicator is orange please wait for the indicator to turn green. Press the reset button for 5-7 seconds to restore the device to default factory settings wait approx. 1 minute for the device to reboot (Signal indicator flashes green). Connect to computers / Ethernet devices Ethernet port 2.
| ENGLISH Hint: Before placing the EM4591 on its destined location, the device needs to be setup. Setting up the EM4591 wireless repeater can be done best, if the EM4591 is located near your wireless router. After setting up the EM4591, you can place the EM4591 at a location defined by using the signal indicator LEDs and the recommended setup as described previously. 3.0 Configure the wireless repeater using the WPS button 1. Please check if your wireless router has a WPS button.
| ENGLISH 6. The connection between your wireless router and the EM4591 wireless repeater will be established automatically (this will take approx. 1 minute including reboot). The signal indicator will stop flashing and indicate the signal strength. *Refer to the manual of your wireless router for the exact duration of pressing the WPS button. This can differ from brand or model. Note: If the WPS button is used, the SSID and network key are the same as used on your wireless router.
| ENGLISH 5.1 Manual configuration (PC) 1. Connect the EM4591 to a wall outlet. 2. Wait for the signal indicator to flash green. 3. Connect to the EM4591 via WiFi SSID: Eminent_repeater or use the Ethernet cable to connect to the EM4591 directly. 4. Launch the internet browser from your computer. 5. You will be redirected to the EM4591 repeater’s user interface. (If in any case it doesn’t, type http://10.0.10.254 in your internet browser and then hit Enter. 6.
| ENGLISH 8. In the next step you will need to enter the WPA Passphrase of the Wi-Fi network you wish to connect to and lick “Apply”. After the settings have been applied, the EM4591 will reboot and connect to your wireless router. 9. The following steps will explain how to configure the EM4591 if the device does not automatically start the wizard. 10.
| ENGLISH 11. The first step of the wizard appears, where you need to select the wireless network you wish to connect to by clicking as shown in the following image: 12. In the next step you will need to enter the WPA Passphrase of the Wi-Fi network you wish to connect to (do not change the other settings).
| ENGLISH 13. Click ‘Apply’ to save and apply the configuration. 14. After the settings have been applied, the EM4591 will reboot and connect to your wireless router. Note: The EM4591 now has the same SSID (no longer “Eminent_repeater”) as the wireless network you connected to in the previous step. To make sure you are connected to the repeater and not the modem/router keep your device close to the repeater (approx. 1m). Turn of your WiFi and turn it back on again.
| ENGLISH 16. You can now connect your wireless network adapter(s) to the EM4591 as described in chapter ‘Connecting a wireless WPS adapter to the EM4591’, or by connecting to the Wi-Fi connection and entering the wireless encryption key of the wireless network you previously connected. 5.2 Manual configuration (Tablet/Smartphone) 1. 2. 3. 4. Connect the EM4591 to a wall outlet. Wait for the signal indicator to flash green. Connect to the EM4591 via WiFi SSID: Eminent_repeater.
| ENGLISH 6. Click next to the wireless network you wish to connect to.
| ENGLISH 7. In the next step you will need to enter the WPA Passphrase of the Wi-Fi network you wish to connect to and lick “Apply”. After the settings have been applied, the EM4591 will reboot and connect to your wireless router. 8. The following steps will explain how to configure the EM4591 if the device does not automatically start the wizard. 9. Click “Quick Connect” 10.
| ENGLISH 11. In the next step you will need to enter the WPA Passphrase of the Wi-Fi network you wish to connect to (do not change the other settings). 12. Click ‘Apply’ to save and apply the configuration. 13. After the settings have been applied, the EM4591 will reboot and connect to your wireless router. Note: The EM4591 now has the same SSID (no longer “Eminent_repeater”) as the wireless network you connected to in the previous step.
| ENGLISH 15. You can now connect your wireless network adapter(s) to the EM4591 as described in chapter ‘Connecting a wireless WPS adapter to the EM4591’, or by connecting to the Wi-Fi connection and entering the wireless encryption key of the wireless network you previously connected. 6.0 Changing the wireless network name (SSID) of the repeater. If you wish to use a different WiFi network name SSID for the EM4591 repeater. You can change this by entering the User Interface of the EM4591.
| ENGLISH 3. Change the SSID name to the preferred name for the WiFi network of the Repeater and click “Apply”. Note: After the settings have been applied, the EM4591 will reboot. Your device will no longer be connected to the wireless network SSID of the EM4591. Reconnect your device to the Wireless network (SSID) you entered in step 3. 7.0 Frequently Asked Questions and other related information The latest Frequently asked questions for your product can be found on the support page of your product.
| ENGLISH 9.0 Warning and points of attention Due to laws, directives and regulations set out by the European parliament, some (wireless) devices could be subject to limitations concerning its use in certain European member states. In certain European member states the use of such devices could be prohibited. Contact your (local) government for more information about this limitations. Always follow up the instructions in the manual*, especially where it concerns devices which need to be assembled.
| ENGLISH 10.0 Warranty conditions The five-year Eminent warranty applies to all Eminent products, unless mentioned otherwise before or during the moment of purchase. After buying a second-hand Eminent product the remaining period of warranty is measured from the moment of purchase by the product’s initial owner. Eminent warranty applies to all Eminent products and parts, indissolubly connected or mounted to the product it concerns.
