E EM6010 – MPEG-4 Security Recorder
| ENGLISH EM6010 – MPEG-4 Security Recorder Warnings and points of attention Opening of the product and/or products can lead to severe injuries! Repairing of the product should be done by qualified Eminent staff! Table of contents 1.0 Warranty conditions...............................................................................................3 2.0 Introduction ...........................................................................................................4 2.1 Functions and features ....
| ENGLISH 8.2 Using the Video Server software......................................................................17 8.2.1 Logging into the EM6010 using Video Server software .................................17 8.2.2 Changing the default password.....................................................................17 8.2.3 Configuring the alarm mail ............................................................................18 8.2.4 Configuring the FTP Function ...........................................
| ENGLISH 2.0 Introduction Congratulations with the purchase of this high-quality Eminent product! This product has undergone extensive testing by Eminent’s technical experts. Should you experience any problems with this product, you are covered by a five-year Eminent warranty. Please keep this manual and the receipt in a safe place. Register your purchase now on www.eminent-online.com and receive product updates! 2.
| ENGLISH The EM6010 comes with a sensor for the remote control. Connect the sensor to the IR input on the back of the DVR (left side). Make sure the receiving side of the IR sensor gets placed in a location where there is unobstructed view, for instance on your monitor or TV. 3.2 Connecting the EM6010 to your TV or video monitor Now that the EM6010 is connected to the power grid you can also connect it to a television, video monitor or LAN network.
| ENGLISH 3.3 Configuring the EM6010 for use in your LAN network The EM6010 can be connected to a LAN network, allowing it to be accessed by computers on the network using the supplied software. The default network address of the EM6010 is 192.168.1.10. If this address does not lie in the range of your network or is already in use, consult your network administrator to receive a correct network address. After receiving the correct information you can change the network address as follows: 1. 2. 3. 4. 5.
| ENGLISH 4.0 First settings Now that the EM6010 has been connected, you will need to change the default passwords so that unauthorized users can not gain access to the EM6010. It is also important that the date and time are correctly configured, allowing you to see at which moment a certain recording was made. 4.
| ENGLISH Hint: If this function is enabled you will need to enter a code before you can configure the EM6010. We recommend you to only enable this option after you are done installing the device. 4.3 Setting the date and time using a TV or video monitor 1. 2. 3. 4. 5. 6. Press the red ‘Menu’ button on the remote control. If the EM6010 asks for a code: Enter the Admin code as set in chapter 4.1. Use the ‘Down’ button to navigate to ‘Date’. Press the ‘Enter’ button.
| ENGLISH 4.5 Software installation (optional) Place the CD-ROM as supplied with the EM6010 in the CD-ROM drive of your computer and follow the steps below to install the software. 1. 2. 3. 4. 5. 6. 7. Choose your language and click ‘Next’. Choose ‘Install Java’ and click ‘Next’. Choose ‘Typical Setup’ and click ‘Accept’. The software will now be installed. Click ‘Finish’. You will now return to the CD-ROM menu. Choose ‘Install Video Server’. The installation will start.
| ENGLISH there are security cameras. The ‘LOOP’ port is meant for analogue cameras equipped with a BNC connection. Make sure you completely fasten the connector until you hear a click. (This type of connector can only be fitted in one manner.) 5.4 Checking the camera image If everything has been correctly connected you should now see an overview of 4 separate camera images on the connected monitor. If this is not the case, press the ‘4CH’ button on the remote control.
| ENGLISH half the amount of disk space. You can even choose to select 6 or 3 IPS. The use of disk space will lower dramatically but the image will be a lot less smooth.
| ENGLISH Using the remote control you can now start recording. If the Auto Keylock has been enabled you will need the administrator code for this function. You can only end the recording by setting the option ‘Manual Record’ in the ‘Record’ menu to ‘OFF’. For this function you will also need the administrator code. 6.4 Time based recording Time based recording allows you to only record during a specified time frame.
| ENGLISH 6.5.1 Configuring motion detection 1. Press the red ‘Menu’ button on the remote control to open the menu of the EM6010. 2. Choose the option ‘Advance’, and press the ‘Enter’ button. 3. Choose the option ‘Detection’, and press the ‘Enter’ button. 4. Choose the option ‘Detection Setup’, and press the ‘Enter’ button. 5. Choose the option ‘Setup’ for the concerning camera. 6. Press the ‘Enter’ button again. 7.
| ENGLISH 6.5.2 Enabling recording after motion detection Now that you configured the motion detection, you can enable the recording after motion detection. 1. 2. 3. 4. 5. 6. 7. 8. Press the red ‘Menu’ button on the remote control to open the menu of the EM6010. Press the ‘Enter’ button to open the ‘Record’ menu. Choose the option ‘Record IMG Size’, nd set it to ‘Frame’ using the ‘Enter’ button. Choose the option ‘Record Quality’, and set it to ‘Best’ using the ‘Enter’ button.
| ENGLISH 7.0 Managing recorded video After the EM6010 has made a recording, you can immediately playback these images, search for a specific time or save the recording to a USB stick, so you can (for instance) hand it to the authorities. 7.1 Immediately playback images 1. 2. 3. 4. 5. 6. Press the ‘Play’ button, on the lower right part of the remote control. The EM6010 will now switch to playback modus. Recording will commence in the background without being disturbed.
| ENGLISH 2. Wait for about 30 seconds. The EM6010 will recognize the stick and give you a message on the screen. 3. Press the red ‘Menu’ button on the remote control to open the menu of the EM6010. 4. Choose the option ‘Advance’, and press the ‘Enter’ button. 5. Choose the option ‘Backup’, and press the ‘Enter’ button. 6. Choose the option ‘USB Backup’ and press the ‘Enter’ button. (It may take up to 1 minute before the next screen appears.) 7.
| ENGLISH 4. 5. 6. Enter ‘admin’ in both the username and password fields and click ‘Submit’. Depending on your security settings your Internet browser may ask you to install a browser plug-in. This is normal and you need to allow/confirm this installation. After a few seconds the managing page will appear Using the remote control on the left part of the screen you can manage the EM6010. These functions are identical to using a real monitor or remote control.
| ENGLISH 8.2.3 Configuring the alarm mail 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Login as described in chapter 8.2.1. Click the ‘System Config’ icon. (Upper right part of the screen, next to the photo camera and film.) Double click ‘Network’. Click ‘Mail’. Enter the e-mail server in the ‘Server’ field. This can be an e-mail server hosted by yourself or an e-mail server from your Internet provider. Consult the data of your Internet provider if you do not know the name of the server.
| ENGLISH The EM6010 will start to save images to the specified FTP server as soon as motion is detected. 8.2.5 Saving images over the network 1. 2. Login as described in chapter 8.2.1. Click the ‘System Config’ icon. (Upper right part of the screen, next to the photo camera and film.) 3. Double click ‘DVR’ and then ‘Network Backup’. 4. Choose ‘Search List’ in the left menu. This function allows you to quickly find a recording. Consult chapter 7.2 for a detailed description of the ‘Search list’. 5.
| ENGLISH Q: My hard disk keeps filling up. This one is too small. Can I place another disk in the EM6010? A: It is possible to place a larger (IDE) disk. Make sure the disk is set to ‘Master’ or ‘Single’. Q: When I playback recordings, the image seems to jolt. How do I solve this? A: The quality of the recording depends on the IPS. If a recording is made with a low IPS the playback will seem to jolt or stutter. Recordings of 25 IPS are the most smooth.
Declaration of Conformity To ensure your safety and compliance of the product with the directives and laws created by the European Commission you can obtain a copy of the Declaration of Conformity concerning your product by sending an e-mail message to: info@eminentonline.com. You can also send a letter to: Eminent Computer Supplies P.O.
