EM6015 Camera Surveillance Kit with recorder
| ENGLISH EM6015 Camera Surveillance Kit with recorder Table of contents 1.0 Introduction ...........................................................................................................3 1.1 Functions and features ......................................................................................3 1.2 Packing contents ...............................................................................................3 2.0 Using the EM6015 ........................................................
| ENGLISH 10.1 Setting up the EM6015 for your mobile phone ...............................................16 10.2 Port Forwarding on the EM4570 wLINK 300 ..................................................17 10.3 Setting up your Mobile phone ........................................................................17 11.0 Mounting a (new) hard disk................................................................................18 12.0 Other functions ..........................................................
| ENGLISH • • Mounting materials Ground Cable 2.0 Using the EM6015 During the following chapters we will explain how to setup the EM6015 and how to install the cameras. It is recommended to setup the EM6015 and install the cameras at your desk before installing and mounting the DVR kit at the desired location. This way, you can easily setup the DVR and check whether the cameras are working correctly. 2.1 Connect the EM6015 to your television or monitor 1. 2. 3. 4.
| ENGLISH Note! The eight other cables from the breakout cable will later be used to power the cameras. 2.5 Installing DVR software (optional) 1. 2. 3. 4. 5. 6. Turn on your computer. Place the CD-ROM your computer’s CD-ROM or DVD player. The software will start automatically. Choose your language. Choose ‘Install Playback Software’. Follow the steps shown on screen to install the software. 3.
| ENGLISH 11. Fill in a password and confirm this password. 12. Click ‘Apply’ after which the DVR saves this password. 13. Click ‘Permissions’. In the following field you can specify the user rights. Make the desired selection. 14. Click ‘Apply’ to save these settings. 15. Click Exit’ until you are at the ‘Account Setup‘ field. 3.1.3 Setting up an admin account 1. 2. 3. 4. 5. 6. 7. 8. 9. Click ‘Config’ at ‘user2’. Select ‘Active’ at the ‘State’ field.
| ENGLISH 4. 5. 6. 7. If there is no DHCP active within your network, or you want to manually fill in an IP address, set ‘Type’ to ‘Static’ and fill in the corresponding IP address data of your network. However, in order to obtain maximum network stability, it is recommended to make use of static IP settings Click ‘Apply’. Click ‘OK’. Click ‘Exit’ until you are at the main menu. In order to obtain maximum network stability, it is recommended to make use of static IP settings.
| ENGLISH - Avoid direct sunlight into the camera, it could cause overexposure - Place the camera on a spot which is not too easy for unwanted people to sabotage the camera 1. 2. 3. 4. Turn off the EM6015 by pressing the ‘Power’ button for a few seconds. A status bar will be shown telling you when the EM6015 will be completely turned off. Take the camera out of the packaging. Connect the video cable of the camera to a ‘Video In’ connection of the EM6015.
| ENGLISH 5.0 Making recordings The default setting of the digital video recorder is set to record images all the time. There are several other manners to make recordings as well. You can make recordings manually, time based recordings, make recordings when motion is detected, but you can also make recordings which are time based combined with motion detection. Besides the different manners to make recordings, you can also adjust the quality and resolution of the recordings.
| ENGLISH 5. 6. 7. 8. 9. Click ‘Record’. Click at the field behind ‘Rec Mode’ and choose ‘Power Up’. Click ‘Apply’. Click ‘OK’ until you are at the main menu. The moment the EM6015 will be started again, recordings will be made continuously. 5.4 Making recordings during motion detection 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Make sure the EM6015 is completely started and you see the EM6015’s image on screen. Click the right mouse button once. Click ‘Main Menu’.
| ENGLISH 9. At the bottom of the screen you will see three coloured squares. If you want, that during an ‘event’ (for example: Motion Detection) an alarm will be generated, then click using the left mouse button the red square and select a time. The selected time will be red marked. 10. Click ‘Save’. 11. Click ‘OK’. 12. Click ‘Exit’ until you are at the main menu’.
| ENGLISH 6.2 Making a backup of a recording The EM6015 is able to copy recordings to a USB memory stick by using the EM6015’s USB 2.0 port. This way, recorded files can be used as evidence. Copying the recordings can take a while, depending on the size of the recordings. 1. 2. 3. 4. 5. 6. 7. Place a mark in the square behind the recording you want to backup. Then click ‘Backup’. You will get a notification on screen saying that the recording is being saved.
| ENGLISH Figure 1. 4. 5. 6. 7. Click the ‘Folder’ icon and browse to the .H264 file you want to convert. Click ‘Open’. Select the ‘Disk’ icon and select a location where you want to save the .AVI to. Click the green arrow to start the conversion. 7.0 Setting up an alarm notification You can setup the EM6015 in such a way, that an alarm notification will be given at the same moment, motion will be detected. Also, you can setup the amount of time this alarm notification will last.
| ENGLISH 11. 12. 13. 14. 15. Fill in at ‘Send PW’ the password. Fill in at ‘Recv Email’ the email address of the recipient. Click ‘APPLY’. Click ‘OK’. Click ‘Exit’ until you are at the main menu. 8.0 Accessing the EM6015 locally You can view the live video of the DVR and change settings on your Windows computer using Internet Explorer. 1. Connect a UTP networking cable to your network (router or switch) and connect the other end to the LAN port of the DVR. 2. Click ‘Main Menu’. 3.
| ENGLISH Hint, you also might need to follow the steps when viewing the webpage externally. 9.0 Accessing the EM6015 externally and the use of dynDNS Sometimes, you can not be on location, but you want to be able to continue monitoring the spaces the EM6015 is watching. In that case you can access the EM6015 using the Internet. In order to access the EM6015 through the Internet, you need to know your WAN IP address. 9.
| ENGLISH 9.2.2 Setting up dynDNS in the EM6015 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Make sure the EM6015 is completely started and you see the EM6015’s image on screen. Click the right mouse button once. Click ‘Main Menu’. Enter your password (if setup before) or leave it empty. Click ‘Advanced’. Click ‘Network’. Click ‘DDNS SETTINGS’. Select ‘ON’ at ‘DDNS’. Choose ‘dyndns’ at ‘Service’. Then fill in the necessary data.
| ENGLISH phone. Refer to the manual of your router how to open ports. During the next chapter we will explain how to open ports on the EM4570 wLINK 300. 10.2 Port Forwarding on the EM4570 wLINK 300 Sometimes, opening ports in your router can be difficult. Therefore, we have created a special chapter which explains how to open/forward port 15962 in the EM4542 wLINK 300 wireless router. This is an example. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Open your web browser (e.g.
| ENGLISH 11.0 Mounting a (new) hard disk Although the EM6015 is equipped with a 500GB hard disk which should provide enough storage capacity, it can occur you want to replace the supplied hard disk for a hard disk with a larger capacity. Use the following steps to mount a new hard disk: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Make sure the EM6015 is disconnected from the power grid and all other cables are disconnected. Remove the screws from the side of the casing.
| ENGLISH A: You can connect a microphone to an ‘Audio-IN’ port to hear sound with your recordings. Connect a microphone to ‘AUDIO-IN’1, then you have to place the microphone near camera 1. Using the ‘AUDIO-OUT’ port you can hear (Mono) sound if a speaker or receiver is connected to this port. Q: I have recorded image and sound. But when I playback the recording, the sound lacks volume. What can I do about it? Follow the steps below: 1.
| ENGLISH Q: A: How can I reset the EM6015? Follow the steps below: 1. Make sure the EM6015 is completely started and you see the EM6015’s image on screen. 2. Click the right mouse button once. 3. Click ‘Main Menu’. 4. Enter your password (if setup before) or leave it empty. 5. Click ‘Advanced’. 6. Click ‘Maintain’. 7. Click ‘Default Settings’. 8. Click ‘All’. 9. Click ‘Load Default’. 10. Click ‘OK’. 11. As soon as the default factory settings have been restored, click ‘OK’ once more. 12.
| ENGLISH 14.0 Service and support This users manual has been carefully written by Eminent’s technical experts. If you have problems installing or using the product, please fill out the support form at the website www.eminent-online.com/support. You can also contact us by phone. Below you will find a list with phone numbers for each supported country.
| ENGLISH otherwise before or during the moment of purchase. When having bought a secondhand Eminent product the remaining period of warranty is measured from the moment of purchase by the product’s first owner. The Eminent warranty applies to all Eminent products and parts inextricably connected to and/or mounted on the main product.