EM6220 e-CamView Pan/Tilt IP camera
| ENGLISH EM6220 – e-CamView Pan/Tilt IP camera Table of contents 1.0 Introduction ........................................................................................................... 3 1.1 Packing contents ............................................................................................... 3 1.2 Requirements to access the camera. ................................................................. 3 1.3 Major hardware components. ...........................................................
| ENGLISH 6.4 FTP setting ...................................................................................................... 23 6.5 Alarm log ......................................................................................................... 24 6.6 Maintenance .................................................................................................... 24 7.0 Restore factory settings ....................................................................................... 24 8.
| ENGLISH 1. Microphone – for receiving the audio/voice. 2. Lens – the lens is inside the camera body and the focus of the lens is fixed, you do not need to spend time to adjust the focus. 3. IR LED – for the Infra-Red lighting of the night mode usage. 4. Day/Night sensor – sensor for day/night detection The major components on the back panel of the EM6220 are the power jack, Ethernet jack and Speaker jack: 1. Speaker jack – connect to an external speaker for two way audio. 2.
| ENGLISH The major components on the bottom of the EM6220 are the bracket screw jack and reset button: 1. Reset button – this is the button to reset the EM6220 to default factory settings. You need to use a small stick like pencil or tooth stick to press the reset button for more than 15 seconds to enable the reset function. Please refer to section 7.0 for more details. 2. Bracket screw jack – this is the position to screw in the bracket of the EM6220.
| ENGLISH 2.2 Installing the e-CamView App on an Apple/Android device Before you can view the video of the camera, you need to download and install the app “e-CamView” from the “Play Store” or “App Store”. 1. 2. 3. 4. 5. Download and install the app “e-CamView” from the “Play Store” or “App Store”. Open e-CamView. Select the “+” button to add the camera to the App. A new window opens to enter the data of the camera. Here you can choose to install the camera: Manually, Scan QR code or LAN Search. 6.
| ENGLISH 6. 7. 8. 9. 10. 11. allow). Click “Device list” to add the camera If the computer and the EM6220 is connected to the same network, the Camera can be added by clicking “open search tool”. Click “search” The devices are displayed with the Device ID in the search list. You add the Camera to the device list by double clicking the device. A new window will be displayed here you can change the name of the camera and enter the password of the camera that is printed on the bottom label.
| ENGLISH 2.4.2 Connecting to Wi-Fi using the PC utility (windows). 1. Ensure the camera is connected to the network with a Ethernet cable. 2. Ensure the camera is added to the device list (see chapter 2.3) 3. Double click the camera in the camera list 4. 5. 6. 7.
| ENGLISH 3.1 On your smartphone/tablet (Android, iPhone, iPad) Start the App e-CamView press the camera-icon of the camera you wish to view. The device will start connecting with the camera and will show live images of the camera. 3.2 On your PC (Windows) in a remote location. After e-CamView software is installed, it’s very easy to add a camera item in the “Camera List” folder of the e-CamView software, key in the CAM ID (from the bottom label).
| ENGLISH Hor. & vert. Patrol Mirror/Flip image Exit live stream Change video resolution Start recording Take Snapshot Change aspect ratio Enable / disable Speaker / Microphone Adjust Contrast and Brightness Default Video settings 4.2 WIFI setting You can select if the camera will use a WiFi connection and what AP or Router it will connect to. Also you can set the encryption settings of the WiFi connection you wish to connect to.
| ENGLISH 4.3 User setting Here you can change the user settings of the Camera.
| ENGLISH 4.4 Time setting Set the time and select the time zone or set the NTP server settings to sync with that server. 4.5 Alarm setting Here you can enable the Alarm, set the alarm triggers and events. Note: The feature IO alarm and IO alarm level is not supported by this device.
| ENGLISH 4.6 FTP setting Here you can set your FTP server settings to enable recording to FTP server Note: If you wish to store in a specified folder please use the WebUI (see section 6.4) 4.7 Mail setting Here you can set your mail settings to enable the e-mail alarm notifications to the email addresses you have set.
| ENGLISH 4.8 SD-card setting This feature is not supported by this device. 5.0 e-Cam-View for PC software 5.1 The layout of e-CamView Pan/Tilt control IO switch (Not supported by device) On Screen Display Set camera preset Hor. & vert. Patrol Go to camera preset Mirror/Flip image Open Rec. settings Open Camera list Enable/disable speaker Enable/disable mic.
| ENGLISH 5.2 Recording settings By default the camera saves the snapshot and recordings to the following path D:\Picture, D:\Record. Note: Please make sure the drive letter D:\ can be used for recording (HDD drive) if this is not the case please change the drive letter to the corresponding drive letter of the HDD drive. 5.3 Base info This option shows you an overview of the cameras status. Here you can also change the devices name.
| ENGLISH 5.4 Time setting Set the time and select the time zone or set the NTP server settings to sync with that server.
| ENGLISH 5.5 Network This feature allows you to change the Network configuration manually after you uncheck the “Obtain IP from DHCP server”. 5.6 SD record scheme This feature is not supported by this device. 5.7 User and password Here you can change the user settings of the Camera.
| ENGLISH 5.8 Email setting Here you can set your mail settings to enable the e-mail alarm notification and to send these notifications to the email addresses you have set. 5.9 FTP setting Here you can set your FTP server settings to enable recording to FTP server Note: If you wish to store in a specified folder please use the WebUI (see section 6.
| ENGLISH 5.10 PTZ Here you can set the Pan/Tilt: boot preset, Speed and the amount of cruise cycles 5.11 Alarm setting Here you can enable the Alarm, set the alarm triggers and events. Note: The feature IO linkage on alarm is not supported by this device.
| ENGLISH 5.12 WIFI setting You can select if the camera will use a WiFi connection and what AP or Router it will connect to. Also you can set the encryption settings of the WiFi connection you wish to connect to. 6.0 The webpage of the camera The Eminent camera is also an IP camera with its own webpage. This means you can login to the webpage by using the camera’s IP Address. Use the following steps to login to the webpage and change any of the camera settings.
| ENGLISH 3. Enter the IP address in the address bar of your web browser followed by : and port number e.g. 192.168.100.101:81 4.
| ENGLISH 6.2 The layout of e-CamView Pan/Tilt control On Screen Display Hor. & vert. Patrol Mirror/Flip image IO switch (Not supported by device) Change video resolution Light Frequency Adjust Contrast and Brightness Frames per second Start recording Enable / disable Speaker Take Snapshot Enable / disable Microphone Settings menu The menu options are the same as the settings menu of the PC software with the exception of Multi Device settings, FTP service settings, Alarm log and Maintenance.
| ENGLISH 6.3 Multi device settings This option will allow you to add additional cameras to the WebUI overview. To add a camera use the IP and port number of the camera you wish to add. 6.4 FTP setting Here you can enter the settings of your FTP server. Note: If you wish to store the snapshots in a predefined folder on your FTP server, please use this option since the APP does not support this extra feature.
| ENGLISH 6.5 Alarm log This log file will keep record of all alarm events of the camera. 6.6 Maintenance This menu option provides the possibility to reboot the device, restore factory defaults or update the firmware. 7.0 Restore factory settings For some reason, for example you forgot the web login password, you may want to set the EM6220 to the factory default settings.
| ENGLISH 8.0 Upgrade Device Firmware If there is a new firmware available for the EM6220, you can upgrade the firmware via the Web UI Maintenance page. A status message about the percentage done in the upgrade procedure is displayed. Please note: do not power off the EM6220 during the upgrade procedure. After the upgrade procedure is finished, the system will restart automatically. For more information about firmware upgrade please see the manual enclosed with the firmware. 9.
| ENGLISH 11.0 Warning and points of attention Due to laws, directives and regulations set out by the European parliament, some (wireless) devices could be subject to limitations concerning its use in certain European member states. In certain European member states the use of such devices could be prohibited. Contact your (local) government for more information about this limitations. Always follow up the instructions in the manual*, especially where it concerns devices which need to be assembled.
| ENGLISH 12.0 Warranty conditions The five-year Eminent warranty applies to all Eminent products, unless mentioned otherwise before or during the moment of purchase. After buying a second-hand Eminent product the remaining period of warranty is measured from the moment of purchase by the product’s initial owner. Eminent warranty applies to all Eminent products and parts, indissolubly connected or mounted to the product it concerns.
