EM6230 e-CamView HD outdoor IP camera
| ENGLISH EM6230 – e-CamView HD outdoor IP camera Table of contents 1.0 Introduction ........................................................................................................... 3 1.1 Packing contents ............................................................................................... 3 1.2 Requirements to access the camera. ................................................................. 3 1.3 Major hardware components. .........................................................
| ENGLISH 6.3 FTP setting ...................................................................................................... 21 6.4 Maintenance .................................................................................................... 21 7.0 Upgrade Device Firmware .................................................................................. 21 8.0 Frequently Asked Questions and other related information .................................. 22 9.0 Service and support.....................
| ENGLISH 1.3 Major hardware components. The major components on the front panel of the EM6230 are: 1. Lens –the focus of the lens is fixed. 2. IR LED – for the Infra-red lighting of the night mode. 3. Power jack – this is the place to plug in the power adapter. The power needed for this EM6230 is 12V/1A, please make sure you are using the correct power adapter. 4. Ethernet jack – this is the place to plug in the RJ45 Ethernet cable. 5. WiFi antenna jack – this is the place to mount the WiFi antenna 2.
| ENGLISH 2.2 Installing the e-CamView App on an Apple/Android device Before you can view the video of the camera, you need to download and install the app “e-CamView” from the “Play Store” or “App Store”. 1. 2. 3. 4. 5. Download and install the app “e-CamView” from the “Play Store” or “App Store”. Open “e-CamView”. Select the “+” button to add the camera to the App. A new window opens to enter the data of the camera. Here you can choose to install the camera: “Manually”, “Scan QR code” or “Search”. 6.
| ENGLISH 2.3 Installing the software and camera on a PC or notebook (Windows). Before you can view the video of the camera, you need to install the software ”eCamView” from the CD-ROM. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Insert the CD in the CD-ROM. If auto-run is enabled the Wizard should start. Run the wizard to install the application e-CamView. The application is installed on the PC Open “e-CamView”. (If prompted with a screen about the firewall click “always allow”).
| ENGLISH to refresh the list) 7. Enter the wireless encryption key and press “Join” 8. Disconnect the Ethernet cable to connect to the wireless network. 2.4.2 Connecting to Wi-Fi using the PC utility (windows). 1. Ensure the camera is connected to the network with a Ethernet cable. 2. Ensure the camera is added to the device list (see chapter 2.3) 3. Double click the camera in the camera list 4. The settings menu will be displayed 5. Go to the Menu option “Wi-Fi” 6.
| ENGLISH 2.5 Mounting the camera on the wall 1. Once the camera is connected correctly with your computer, you can mount the camera on a wall or ceiling. 2. Use the mounting stand to mark the holes at the location where you want to mount the camera. 3. Drill the holes and fill the holes with the supplied plugs. 4. Mount the bracket stand to the wall or ceiling using the supplied screws. 5. Connect the power supply into the wall socket and connect the power tip to the camera. 3.
| ENGLISH 4.0 e-CamView for iPhone/iPad/Android 4.1 The Layout of e-CamView Edit Camera Add Camera View Camera Camera settings App information Alarm events View snapshots Hor. & vert.
| ENGLISH 4.2 WIFI setting You can select if the camera will use a WiFi connection and what AP or Router it will connect to.
| ENGLISH 4.3 User setting Here you can change the user settings of the Camera. 4.4 Time setting Set the time and select the time zone or set the NTP server settings to sync with that server.
| ENGLISH 4.5 Alarm setting Here you can enable the Alarm, set the alarm triggers and events. 4.6 FTP setting Here you can set your FTP server settings. Example of a FTP server address: ftp.server.com Note: If you wish to store in a specified folder please use the WebUI (see section 6.
| ENGLISH 4.7 Mail setting Here you can set your mail settings to enable the e-mail alarm notifications to the email addresses you have set. 4.8 SD-card setting This feature is not supported by this device.
| ENGLISH 5.0 e-CamView for PC software 5.1 The layout of e-CamView Pan/Tilt control Mirror/Flip image On Screen Display Hor. & vert. Patrol Set camera preset Go to camera preset Open Rec. settings Open Camera list Enable/disable speaker Enable/disable mic.
| ENGLISH 5.2 Recording settings By default the camera saves the snapshot and recordings to the following path D:\Picture, D:\Record. Note: Please make sure the drive letter D:\ can be used for recording (HDD drive) if this is not the case please change the drive letter to the corresponding drive letter of the HDD drive. 5.3 Base info This option shows you an overview of the cameras status. Here you can also change the devices name.
| ENGLISH 5.4 Time setting Set the time and select the time zone or set the NTP server settings to sync with that server. 5.5 Network This feature allows you to change the Network configuration manually after you uncheck the “Obtain IP from DHCP server”.
| ENGLISH 5.6 SD record scheme This feature is not supported by this device. 5.7 User and password Here you can change the user settings of the Camera. 5.8 Email setting Here you can set your mail settings to enable the e-mail alarm notification and to send these notifications to the email addresses you have set.
| ENGLISH 5.9 FTP setting Here you can set your FTP server settings to enable recording to FTP server Example of a FTP server address: ftp.server.com Note: If you wish to store in a specified folder please use the WebUI (see section 6.3) 5.10 PTZ This feature is not supported by this device. 5.11 Alarm setting Here you can enable the Alarm, set the alarm triggers and events. Note: The feature IO linkage on alarm is not supported by this device.
| ENGLISH 5.12 WIFI setting You can select if the camera will use a WiFi connection and what AP or Router it will connect to. Also you can set the encryption settings of the WiFi connection you wish to connect to. 6.0 The webpage of the camera The Eminent camera is also an IP camera with its own webpage. This means you can login to the webpage by using the camera’s IP Address. Use the following steps to login to the webpage and change any of the camera settings.
| ENGLISH 3. Enter the IP address in the address bar of your web browser followed by : and port number e.g. 192.168.100.101:81 4. Login with user: admin Password: (Leave blank) 6.2 The layout of e-CamView Change video resolution Start recording Take Snapshot Zoom Enable / disable Speaker Enable / disable Microphone Recording path Record at alarm event The menu options are the same as the settings menu of the PC software with the exception of FTP service settings and Maintenance.
| ENGLISH 6.3 FTP setting Here you can enter the settings of your FTP server. Example of a FTP server address: ftp.server.com Note: If you wish to store the snapshots in a predefined folder on your FTP server, please use this option since the APP does not support this extra feature. Enter the folder name in the “Path” field and press “OK” then press “Test” to test if the folder is created successfully. 6.
| ENGLISH 8.0 Frequently Asked Questions and other related information The latest Frequently asked questions for your product can be found on the support page of your product. Eminent will update these pages frequently to assure you have the most recent information. Visit www.eminent-online.com for more information about your product. 9.0 Service and support This users manual has been carefully written by Eminent’s technical experts.
| ENGLISH Also, you will find frequently asked questions in the FAQ section. It is highly recommended to consult the FAQ section. Very often the answer to your questions will be found here. 11.0 Warranty conditions The five-year Eminent warranty applies to all Eminent products, unless mentioned otherwise before or during the moment of purchase. After buying a second-hand Eminent product the remaining period of warranty is measured from the moment of purchase by the product’s initial owner.
