EM7080 - hdMEDIA RT
| ENGLISH EM7080 - hdMEDIA RT Warnings and points of attention Repairing of the product should be done by qualified Eminent staff! Table of contents 1.0 Introduction .............................................................................................................. 3 1.1 Functions and features ........................................................................................ 3 1.2 Packing contents ..........................................................................................
| ENGLISH 12.1 Setting up your router (EM4551) for the Bit torrent module ............................. 18 12.2 Using the Bit torrent module ............................................................................ 19 13.0 The NZB module of the EM7080 ......................................................................... 19 13.1 Setting up the NZBget module......................................................................... 19 13.2 Using the NZBget module ......................................
| ENGLISH • • Remote control User Manual 2.0 Explanation of the media player The media player has the following connections on the back of the casing: 1. 2. 3. 4. 5. 6. 7. 8. Network connection. Connect your network cable to this connection. HDMI 1.3 connection. Use this connection to connect the hdMEDIA RT to the HDMI connection on your television. Component connection. Use these connections to connect the hdMEDIA RT to the component connections on your television. Composite connections.
| ENGLISH 3.0 Explanation of the remote control In the following chapter, we will explain the remote control. The picture below displays the different buttons and we will explain which functions these buttons have. 1. On/Off switch. Use this button to turn on or turn off the EM7080. 2. Eject button. Use to open or close the tray of the DVD player. 3. These button are the alphanumeric buttons, used to enter data. 4. Menu button. Used to access the menu. 5. Function buttons.
| ENGLISH 1. Take your EM7080 and remove the screws on all four corners on the bottom of the device. 2. Gently remove the lid. Be careful, the fan is connected to main board! 3. Disconnect the fan from the fan connector. Note the orientation of the connector. 4. Place the lid safely out of the way for now. 5. Lower the SATA hard disk into the media player. 6. Note the grey SATA connector on the main board, and slide the disk into it. 7.
| ENGLISH 5.2 Connecting the media player using component (Y/Pb/Pr) If your television is not equipped with an HDMI connection, or your HDMI connections are already occupied, you can connect the EM7080 using component. Using component, you can also use HD resolutions. 1. 2. 3. Connect the red plug to the red component connection on the EM7080. Connect the blue plug to the blue component connection on the EM7080. Connect the green plug to the green component connection on the EM7080.
| ENGLISH to enjoy DTS-HD sounds. Audio with DTS-HD tracks will be played back as DTS-Core audio over TOSLINK. 5.5 Connecting to your network The media player also has the capability to be connected to your network by using the media player’s 100Mbps network connection. Doing so, you can retrieve media from your network or your NAS (For example: The Eminent NAS type EM4071 or EM4072) and play these media files through the media player on your television. 1. 2.
| ENGLISH 6.2 Language settings 1. 2. 3. 4. 5. Use the arrow keys on the remote control to navigate to ‘Setup’ and press the ‘OK’ key on the remote control. Navigate to ‘System’. Select ‘Menu Language’ and press the ‘OK’ button. Use the arrow keys to select the desired language at the right side of the menu. Once the desired language is selected, press the ‘OK’ button to save the this setting. Press the ‘HOME’ button to return to the main menu. 6.3 Video settings 1. 2. 3. 4. 5. 6.
| ENGLISH 4. SPDIF RAW, if you have only connected the HDMI cable, then select HDMI RAW which enables the playback of virtually any audio codec. Press the ‘HOME’ button to return to the main menu. If you are using a DTS sound system, you can use the ‘RAW’ settings in order to receive digital sound. 6.6 Network setup In the following steps we will explain how to setup the media player for network usage. 1. 2. 3. 4.
| ENGLISH 1. 2. 3. 4. 5. Make sure your computer is completely started. Make sure the media player is turned on and is completely started. Connect the USB cable to the USB port at the back of the EM7080. Connect the other side of the USB cable to a free USB port on your computer. A message will appear on your television: ‘USB Plug-in event Detected’. Select ‘Confirm’ and press the ‘OK’ button. 6. Now use the Windows Explorer on your computer to browse to the local hard disks. 7.
| ENGLISH 10. You can now select the folder you want to copy to and press the ‘OK’ button, or you can select ‘NEW DIRECTORY’ and press the ‘OK’ button. 11. If you have selected ‘NEW DIRECTORY’, you can now give a name to the folder using the remote control. Once you have given the folder the correct name, navigate to ‘OK’ in the menu and press the ‘OK’ button. 12. Press the right arrow key. You will be asked to ‘COPY’, ‘MOVE’ or ‘CANCEL’. Select ‘COPY’ and press the ‘OK’ button 13.
| ENGLISH Note: Press the ‘SUBTITLES’ button to see subtitles or change the language of the subtitles, size of the subtitles, color of the subtitle etc. Press the ‘MENU’ button to access the menu which allows you to easy access to the chapter list and subtitle languages. 9.2 DVD playback 9.2.1 DVD ISO 1. 2. 3. 4. 5. 6. 7. Make sure the media player is turned on and is completely started. Use the arrow keys to navigate to ‘Movies’ and press the ‘OK’ button.
| ENGLISH 1. 2. 3. 4. 5. 6. 7. Make sure the media player is turned on and is completely started. Use the arrow keys to navigate to ‘Movies’ and press the ‘OK’ button. Select the device or source you want to use for video playback. Select ‘HDD’ if you want to playback video files located on the internal hard disk and press the ‘OK’ button. Select the hard disk and press the ‘OK’ button. Select the folder where the video files are located and press the ‘OK’ button. The video files will now be shown.
| ENGLISH 5. 6. 7. 8. Select the folder where the images are located and press the ‘OK’ button. Select the image you want to view and press the ‘OK’ button. An image will appear on the right side. Press the ‘OK’ button again to view the image in full screen. If you have set slideshow settings in the chapter ‘Photo settings’, the slideshow and corresponding visual effects will start automatically. 9.
| ENGLISH 2. 3. 4. Click ‘Programs’. Click ‘Windows Media Player ‘. Click ‘Tools’, then click ‘Options’. The following screen will be displayed: 5. 6. 7. Go to the ‘Library’ tab in the left upper corner of the options window. Now click ‘Configure sharing’. Check the “Share my media” checkbox and click OK. 8. 9. 10. 11. 12. 13. A list with detected devices will appear within a few seconds. Click the name of your media player. Click ‘Allow’. Click ‘Ok’. Click ‘Ok’.
| ENGLISH 2. 3. 4. 5. Use the arrow keys to navigate to ‘Movies’. Select ‘UPNP’ and press the ‘OK’ button. Now you will see a list of available (media) servers in your network. Select the desired UPnP (media) server and press the ‘OK’ button on the remote control. The available media folders and files will now be displayed. Select the media folder or file you want play and press the ‘OK’ button on the remote control to start the playback of the file. 10.3 Play media through your network (Samba) 1. 2.
| ENGLISH 11.2 Using the Samba server Now you have setup the Samba server, you can now use your computer to access the media player and transfer data to the media player’s hard disk and transfer data from the media player’s hard disk to your computer. For this, you need to know the media player’s IP-address. This IP-address can be found using the menu of the media player. 1. 2. 3. 4. 5. 6. Make sure your computer is completely started. Open the Windows explorer.
| ENGLISH 13. 14. 15. 16. 17. 18. At ‘LAN IP Address’ you have to fill in the media player’s IP-address. Select ‘TCP’ at ‘Protocol’. Fill in ‘6881~6881’ at ‘External Port’. Fill in ‘6881~6881’ at ‘Internal Port’. Click ‘Add’. If correct, the new rule will displayed at the lower part of the screen. Make sure the name of the rule is marked, and click ‘Run’ to activate this rule. Your router has now been configured for using the Bit torrent module. 12.2 Using the Bit torrent module 1. 2. 3. 4. 5. 6. 7.
| ENGLISH 5. 6. Click ‘News-Servers’ at the left side of the menu. Fill in the name of you news server at ‘Server1.Host’. For example: news.provider.com. 7. Fill in the username of your new server if required at ‘Server1.Username’. 8. Fill in the password of your newsserver if required at ‘Server1.Password’. 9. Click ‘Save changes’ to save these settings. 10. Click ‘Shutdown’ in the left menu, and wait for 10 seconds. 11. Turn off the media player using the remote control.
| ENGLISH System System Update: Using this function, the current firmware can be updated. Parental Control: Let’s you set the strictness of the parental control. A password is required. HDD Format: Let’s you format the hard drive. Ideal when a new hard drive is installed, or the data on you current hard disk is corrupted. MISC Resume Play: Allows you to resume the media file where you left of. This is handy, in case you are not able to view the entire movie at once.
| ENGLISH Q: A: What file systems does the EM7080 hdMEDIA RT support? The hdMEDIA RT supports NTFS and FAT32 file systems. The hdMEDIA RT can also read EXT3 file systems. Q: I want to delete media content from the internal hard disk. How can I do this? You can delete content by selecting the desired file and pressing the blue button on the remote control. Select ‘Delete’ and press the ‘OK’ button to remove the selected file. A: Q: A: I am trying to update the firmware using USB.
| ENGLISH hand Eminent product the remaining period of warranty is measured from the moment of purchase by the product’s first owner. The Eminent warranty applies to all Eminent products and parts inextricably connected to and/or mounted on the main product.
EM7080 | 03-2010
