Instructions

ManualsBrandsEmko ManualsAutomationBang-bang Temperature controller K 0 up to 999 °C 5 A relay (L x W x H) 62 x 35 x

Table Of Contents

ESM-1510N DIN Rail Mounting Temperature Controller

- 3 Digits display

- NTC Input or,

PTC Input or,

J type thermocouple Input or,

K type thermocouple Input or,

2-Wire PT 100 Input or,

2-Wire PT 1000 Input (It must be determined in order)

- ON/OFF temperature control

- Selectable heating or cooling function

- Selection of operation with hysteresis

- Adjustable temperature offset

- Set value low limit and set value high limit boundaries

- Relay or SSR driver output

- Operation selection of compressor operates continuously, stops

or operates periodically in case of probe defect

- Compressor protection delays

- Password protection for programming mode

Instruction Manual. ENG ESM-1510N 01 V00 02/16

ESM-1510N DIN Rail Mounting Type

Digital, ON / OFF Temperature Controller

1.Preface

1.2 General Specifications

ESM-1510N series temperature controllers are designed for measuring and controlling

temperature. They can be used in many applications with their On / Off control form, heating and

cooling control form and easy-use properties. Some application fields which they are used are

below:

Application Fields Applications

Glass Heating

Food Baking Ovens

Plastic Incubators

Petro-Chemistry Storages

Textile, Automative Air Conditioning

Machine Production Industries Etc...

Etc...

Operating Temperature : 0 to 50 °C

Max. Operating Humidity : 90% Rh (non-condensing)

Altitude : Up to 2000 m.

Forbidden Conditions:

Corrosive atmosphere, Explosive atmosphere,

Home applications (The unit is only for industrial applications)

1.1 Operating Conditions

ESM-1510N

Optional

Standard

Control Output

Alarm Output

NTC

PTC

J or K Type TC

2-wire PT 100

2-wire PT 1000

Output-1

(SSr Driver Output)

Control Output

Alarm Output

Heating or Cooling

Function

ON/OFF Operation

Temperature Sensor

Input

Power Supply

Input

Standard

230 V V (±%15) , 50/60Hz

Optional Supply Input

115 V V (±%15) , 50/60Hz

24 V V (±%15) , 50/60Hz

10...30 V Z

24 V W (-%15, +%10),

50/60Hz

Output-1

(Relay Output)

1.4 Warranty

EMKO Elektronik warrants that the equipment delivered is free from defects in material and

workmanship. This warranty is provided for a period of two years. The warranty period starts from

the delivery date. This warranty is in force if duty and responsibilities which are determined in

warranty document and instruction manual performs by the customer completely.

1.5 Maintenance

Repairs should only be performed by trained and specialized personnel. Cut power to the device

before accessing internal parts.

Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of

these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl

alcohol or water to clean the external plastic case.

In package ,

- One piece unit

- One piece rail lock apparatus

- One piece instruction manual

A visual inspection of this product for possible damage occured during shipment is

recommended before installation. It is your responsibility to ensure that qualified

mechanical and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power

off the system and separate the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch

and fuse as required.

Be sure to use the rated power supply voltage to protect the unit against damage and to

prevent failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble

with the unit can be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may

results in malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During the equipment is putted in hole on the metal panel while mechanical installation

some metal burrs can cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s fixing clamps. Do not do the

montage of the device with inappropriate fixing clamp. Be sure that device will not fall

while doing the montage.

It is your responsibility if this equipment is used in a manner not specified in this

instruction manual.

Before beginning installation of this product, please read the instruction

manual and warnings below carefully.

1.3 Installation

2 General Description

2.1 Front View and Dimensions of ESM-1510N Temperature Controller

4.6 Entering To The Programming Mode, Changing and Saving Parameters

If no operation is performed in Programming mode for 20 seconds, device turns to

operation screen automatically

Press increment button

for accessing to the

password entering

screen.

Enter programming

mode accessing

password with

increment and

decrement buttons

Press SET/OK button

for accessing to the

parameters

Operation Screen

Password Entering

Screeen

When SET button is pressed for 5

seconds, “P” led starts to blink. If

programming mode entering password is

different from 0, programming mode

entering screen will be observed.

5 secs

Programming Mode

Entering Screen

Note-2: Parameters can be observed by pressing SET/OK button in

password entering screen without entering the programming mode

entering password. But parameters can not be changed.

Note-1: If programming mode accessing password is 0, hysteresis

screen is observed instead of Programming screen

accessing password

Password Entering

Screeen

Parameter is accessed

by pressing increment

button. If set button is

pressed, next

parameter is shown.

Hysteresis Parameter

Value

Change the

parameter with

increment and

decrement buttons

If no operation is performed in Programming mode for 20 seconds, device turns to

operation screen automatically

Hysteresis Parameter

Value

Press Set button for

saving the parameter

value

Hysteresis Parameter

Minimum Set Value

Parameter

Minimum Set Value

Parameter is

accessed by pressing

increment button. If

set button is pressed,

next parameter is

shown.

Minimum Set Value

Other Programming mode parameters can be accessed

with the same method explained above, observed and

changed.

Press Set button for

accessing to the next

parameter

Change the

parameter with

increment and

decrement buttons

Minimum Set Value

Parameter

Press Set button for

saving the parameter

value

7. Specifications

Device Type : Temperature Controller

Housing&Mounting : 86mm x 35mm x 59mm plastic housing for Rail Mounting.

Protection Class : IP20.

Weight : Approximately 0.14 Kg.

Environmental Ratings : Standard, indoor at an altitude of less than 2000 meters

with none condensing humidity.

oooo

Storage / Operating Temperature: -40 C to +85 C / 0 C to +50 C

Storage / Operating Humidity : 90 % max. (None condensing)

Installation : DIN Rail Mounting

Overvoltage Category : II.

Pollution Degree : II, office or workplace, none conductive pollution

Operating Conditions : Continuous

Supply Voltage and Power : 230 V V (± 15%) 50/60 Hz. 1.5 VA

115 V V (± 15%) 50/60 Hz. 1.5 VA

24 V V (± 15%) 50/60 Hz. 1.5 VA

24 V W (- 15%, + 10%) 50/60 Hz. 1.5 VA

10...30 V Z 1.5 W

Temperature Sensor Inputs : NTC, PTC, TC, RTD

NTC Input Type : NTC (10 kW @.25 °C )

PTC Input Type : PTC (1000 W @.25 °C )

Thermocouple Input Types : J, K (IEC584.1)(ITS90)

Thermoresistance Input Type : PT-100, PT-1000 (IEC751)(ITS90)

Accuracy : ±1% of full scale for thermocouple and thermoresistance

Cold Junction Compensation : Automatically ± 0.1°C/1°C.

Sensor Break Protection : Upscale

Sampling Cycle : 3 samples per second

Control Form : ON / OFF

Relay Output : Resistive Load 5 A@250 V V

(Electrical Life : 100.000 operation (Full Load)

Optional SSR Output : Maximum 28 mA, Maximum 15 V Z

Display : 9 mm Red 3 digits LED Display

Leds : SV (Green) , OUT (Red) , P(Red) 3 mm

Approvals : GOST-R,

6. Ordering Information

All order information of ESM-1510N

Temperature Controller are given on the

table at left. User may form appropriate

device configuration from information and

codes that at the table and convert it to the

ordering codes.

Firstly, supply voltage then other

specifications must be determined. Please

fill the order code blanks according to your

needs.

Please contact us, if your needs are

out of the standards.

V Symbol means Vac,

Z Symbol means Vdc,

Symbol means Vac/dcW

A BC D E FG HI /

V W Z/

0 00 2 0 0

Relay Output ( resistive load 10 A@250 V V , 1 NO + 1NC )

Output-1

Supply VoltageA

Input Type

Scale(°C)

ESM-1510N (77x35 DIN Size)

24V V ( ± 15% ) 50/60Hz

115V V ( ± 15% ) 50/60Hz

230V V ( ± 15% ) 50/60Hz

10...30 V Z

Customer

SSR Driver Output (Maximum 28 mA, 15 V Z)

J ,Fe CuNi IEC584.1(ITS90)

PTC (Note-1)

-50°C

150°C

0°C

800°C

-19.9°C

99.9°C

PT 100 , IEC751(ITS90)

K ,NiCr Ni IEC584.1(ITS90)

-50°C

400°C

0°C

999°C

PT 100 , IEC751(ITS90)

-50°C

400°C

PT 1000 , IEC751(ITS90)

-19.9°C

99.9°C

PT 1000 , IEC751(ITS90)

PTC (Note-1)

-19.9°C

99.9°C

Temp. Sensor which is given with ESM 1510

None

PTC-M6L40.K1.5 (PTC Air Probe with 1.5 m silicon cable)

PTCS-M6L30.K1.5.1/8” (PTC Liquid Probe with 1.5 m silicon

cable)

Customer

NTC-M5L20.K1.5 (NTC Probe, thermoplastic moulded with

1.5 m cable for cooling application)

NTC-M6L50.K1.5 (NTC Probe, stainless steel housing with

1.5 m cable for cooling application)

Note-1 : If input type is selected PTC or NTC (BC = 12, 15, 18, 19 ),

Temperature sensor is given with the device. For this reason,

If input type is selected as PTC, sensor type (V = 0,1 or 2) or

If input type is selected as NTC, sensor type (V = 0,3 or 4) must be

declared in ordering information.

-19.9°C 99.9°C

-50°C 100°C

NTC (Note-1)

24V W ( -15%,+10% ) 50/60Hz

5. Failure Messages in ESM-1510N Temperature Controller

Probe defect in analogue inputs. Sensor connection is wrong or

there is no sensor connection.

Manufacturer Information:

Emko Elektronik Sanayi ve Ticaret A.Þ.

Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA / TURKEY

Tel : +90 224 261 1900

Fax : +90 224 261 1912

Repair and maintenance service information:

Emko Elektronik Sanayi ve Ticaret A.Þ.

Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA / TURKEY

Tel : +90 224 261 1900

Fax : +90 224 261 1912

8. Other Informations

Your Technology Partner

www.emkoelektronik.com.tr

Thank you very much for your preference to

use Emko Elektronik products, please visit our

web page to download user manual.

Rail Lock Apparatus

35 mm / 1.38 inch

90 mm / 3.54 inch

61.2 mm / 2.40 inch

35.7 mm / 1.40 inch

46.5 mm / 1.83 inch

78910

Summary of content (2 pages)

PAGE 1
4.6 Entering To The Programming Mode, Changing and Saving Parameters 1.Preface Minimum Set Value Parameter Parameter is accessed by pressing increment button. If set button is pressed, next parameter is shown. Note-2: Parameters can be observed by pressing SET/OK button in password entering screen without entering the programming mode entering password. But parameters can not be changed.
PAGE 2
3. Electrical Wiring Diagram 2.2 Installation onto the Rail 4.3 Program Parameters 4.2 Changing and Saving Set Value Temperature Sensor Input (TC, NTC, PTC, PT-100 or PT-1000) Hysteresis Parameter for Output ( Default = 1 ) 1 to 100 °C for TC Type Devices, 1 to 100 °C for PT-100 (-50°C, 400°C) and PT-1000 (-50°C, 400°C), 0.1 to 10.0 °C for PT-100 (-19.9°C, 99.9°C) and PT-1000 (-19.9°C, 99.9°C), 1 to 20 °C for PTC (-50°C, 150°C) and NTC (-50°C, 100°C), 0.1 to 10.0 °C for PTC (-19.9°C, 99.