Measurement Guide

a-6 Use a braket to mark the placement of the bracket on the line.
a-7 Drill pilot holes for the screws.
Note 2
Note 3
Note 4
OUT
21
65
3
4
7
2
1
6
5
3
4
7
Lock
a-3 Insert ‘OUT’ end cap into an outer rod and tighten the screw to lock it in place.
a-5 Mark the postion of the mount by placing the track on the line.
a-4 Install the outer track segment with the end cap.(See Note 4 for recommended
bracket positions.
a-10 Mount the track onto the bracket through the keyhole, shift the track into place,
and tighten the screw to lock the track inplace
a-11 After mounting the outer track, insert the sliders.
Example of Six Panel Track Installation
Note 1
OUT
*Refer to the chart for slider count and overall length of the installation.
Remove the end caps and screw the finials onto the cap.(The end caps
are labeld ‘IN’ and ‘OUT’. Make sure to insert the end caps back to the
correct ends. )
Double Track Clip
The clips has 2 side: one side is for clipping inner tracks together,the other for outer
tracks Place the clip 1½” from the end of the tracks.
Bracket Mounting Position
1.5”
Slider Return
Position for
16” Slider
Slider Return Position
for 23” Slider
Panel Track Installation Instructions
Draw left
(shown), baton is
in front of the
panels
Bracket Finials RodSliders KeyholeBatonPanel Curtains
(Sold Separately)
For installation drawing from left to right,
baton sits in front of the panel.
For installation drawing from right to left,
baton sits behind the panel.
/
Recommended Slider Count for Coverage Needed
• For ceiling installations, finials cannot be used.
• Your installation needs may differ from the example shown.
Tools
Dry Wall Anchors
For Studs
Drill a 1/8” pilot hole and mount the brackets onto the wall with the screws.
For Dry Wall
Drill a 3/16” pilot hole, hammer in the dry wall anchor,and mount the
brackets on to the wall with screws.
Finials(Sold Separately)
Wall Installation (for ceiling installation, see step1.b)
a-1 Measure the length of the coverage needed. Don’t forget to include the finials
if installing.
Measure
a-2 Draw a line where the brackets will be installed.
Level
Loosen the screw
Press on the metal tab
and open it for insertion
‘OUT’ end cap
Tighten the screwLightly press on the outer rod Insert end cap
Loosen the screw Push down Tighten
a-8 Loosen the screws and mount the brackets through their keyhole slots.Screw in
the bottom screw to secure the brackets.
a-9 Loosen the furthest screw on the extended part of the bracket.
Loosen the screw one turn
Mount the rod onto the brackets Shift the rod into place Tighten the screws
Side Front Side Front
a-12 Remove the red pin that holds the slider together (can be reused to assist with
the rest of the installation.)
Side for Outer Tracks
For Inner Tracks
Step1.a
Outer
Inner&Outer
The keyhole
have to in the
same direction.
Inner and Outer Track Join Pattern
Outer TrackInner Track
OuterInner
Outer
Outer
Outer
Outer
Outer
Outer
Outer
Outer
Outer Outer
Inner
Inner
Inner
Inner
Inner Inner
Inner
Inner
Inner
Slider
Count
6 Count
5 Count
4 Count
3 Count
Double
Track
Double
Track
Double
Track
8 Count
10 Count
12 Count
Slider Length
16”
Slider Length
23”
16~43”
16~57”
16~71”
16~85”
23~67”
23~89”
23~110”
23~175”
23~218”
23~262”
23~132”
Required brackets placement for proper loading, spread the rest of the brackets out evenly
First, 4th and last keyhole
Count
6
8
(Double Track)
10 (Double Track)
12 (Double Track)
5
4
3
16” Slider 23” Slider
First, 5th and last keyhole
First
, 5th and last keyhole
First
, 5th and last keyhole
First
, 5th and last keyhole
First
, 5th and last keyhole
First
, 5th and last keyhole
First
, 5th and last keyhole
First
, 4th and last keyhole
First
, 4th and last keyhole
First
, 4th and last keyhole
First
, 4th and last keyhole
First
, 4th and last keyhole
First
, 4th and last keyhole
International patent owned by US ABO Window Fashion.
Licensed to Taiwan SYN YAO Enterprise Co. Ltd.
This QR code
leads to multilingual
operating instructions
OUT