User`s guide
Table Of Contents
- TABLE OF CONTENTS
- Safety Precautions
- NEC (National Electrical Code) Standards
- A Note for the Cable Television (CATV) Installer
- Antenna Grounding Outside the House
- Thank You for your DMC-1 Purchase
- Unpacking the DMC-1
- Recording the Serial Number
- Features of the DMC-1 A/V Controller
- DMC-1 Front Panel Features
- Power Button
- IR Receiver Window
- Processor Display
- Z II (Zone 2)
- Input Select Buttons
- MODE UP/DOWN (Mode Buttons)
- AM/FM Tuner Controls
- Tone Controls
- Signal Processing Indicator Lights
- Additional Front Panel Features
- COM/RECV
- ZONE TWO POWER
- ZONE TWO ADJUST
- SIDE AXIS
- PANEL DIM Button
- MUTE Button
- DMC-1 Rear Panel Layout
- Component Video In
- Component Video Out
- Audio/Video Inputs
- Audio/Video Outputs
- Triggers and Relay
- Infrared (IR) Inputs
- RS-232 Port
- 8-CH Analog Input
- Main Audio Outputs
- XLR Audio Outputs
- Audio Inputs
- Ground Screw
- FM Antenna
- AM Antenna
- Side-Axis Outputs
- Stereo Outputs
- Audio Outputs
- IEC Line Cord Socket
- Digital Inputs
- Digital Output
- IEEE-1394 "Firewire" Port
- Installation and Connections
- AC Power Considerations
- Connection Tips for Superior Sound
- Connection Tips for Video Quality and Flexibility
- What is Composite Video?
- What is S-Video?
- What is Component Video?
- Video Up Conversion
- Video Output to the Main Screen and OSD
- Zone Specific Turn-On Triggers
- Connection Diagrams
- Connecting a DVD-Video Player (Analog Audio and Composite Video)
- Connecting a DVD-Video Player (Digital Audio and Component Video)
- Connecting to the TV or Projector using Component Video
- Connecting a VCR (Analog Audio and Composite Video)
- Connecting a CD Player (Analog Audio)
- Connecting a Cassette Tape or DAT Deck
- Connecting the 8-Channel Analog Inputs
- Connecting the AM and FM Antennas
- Connecting an Amplifier (MAIN ZONE)
- Connecting an Amplifier (ZONE 2)
- Connecting an Amplifier (ZONE 2)
- Overview of the DMC-1 Remote
- Button Layout
- Button and Display Light
- LCD Display
- DEVICE Buttons
- PAGE Button
- MAIN Button
- FAV Button
- JOYSTICK PAD
- M1, M2 and M3 Macro Buttons
- Quick Start Setup Instructions
- Adding Batteries to the Remote Control
- Quick Start Instructions for DMC-1 Setup
- Operation of the DMC-1 using the Remote
- Turning on the MAIN Zone
- Turning on ZONE 2
- Programming and Configuring YOUR Components
- P-PRO
- LEARN
- EDIT
- FAV
- PUNCH
- ERASE
- LIGHT
- MACRO
- RECAL (Recall)
- CLONE
- The On-Screen Display (OSD) Functions
- Video Connections
- OSD Activation
- Quick Access to Information
- OSD Menus
- How to Navigate the OSD Menus
- TRIM Menu
- MODES Menu
- Dynamic Range
- Pro Logic IIx Sub Menu
- DTS LFE
- DTS Neo:6
- Party
- Jazz Club Ambience
- TONE Menu
- INPUTS Menu
- INPUT CONFIGURATION MENUS (The example shows the DVD menu)
- Tuner Preset Menu
- Saving AM/FM Presets
- SETTINGS Menus
- MAIN ZONE Menu
- ZONE 2 Menu
- SPEAKERS Menu - SIZE
- SPEAKERS Menu - POSITION
- SPEAKERS Menu - CALIBRATION
- Crossover Adjustment
- Subwoofer Mode
- VIDEO Menu
- SOFTWARE Menu
- CONTROL Menu
- Special Features of the Emotiva DMC-1
- Bass Management
- Surround Modes for 2 Channel Source Material
- Surround Modes for Multi-Channel Sources
- Tuner Operation
- Recording
- Zone 2 Operation
- Speaker Placement Tips
- Tips Before You Begin
- The Front Speakers
- The Center Speaker
- Side-Axis Speakers
- The Surround Speakers
- Surround Back Speakers
- Subwoofer Location
- Remote Control Codes
- Audio Components
- Auxiliary Devices
- Cable Boxes
- CD Players
- DVD Players
- Laserdisc Players
- Satellite/DSS Receivers
- Tape Decks
- Televisions
- VCRs
- Troubleshooting Guide
- No Sound (from one or more full range speakers)
- No Subwoofer (or poor output)
- Poor AM Reception
- Poor FM Reception
- Input Selection Problems
- There is No TV Picture
- No Tone Control Functions
- No Dolby Digital or DTS Playback
- No On Screen Display
- Remote Won't Learn Commands or Codes
- Remote Not Working
- ZONE 2 Not Working
- External Amplifier(s) Shut Down (Often or Prematurely)
- DMC-1 "Locks Up" (No Response)
- Reset Procedure
- Problems Updating DMC-1 Firmware
- "Hum" Noises
- Other Probable Causes of Noise
- Favorite Settings Log
- Tone Settings
- Main Zone Settings
- Zone 2 Settings
- Mode Settings
- Control Settings
- Video Settings
- Input Settings and Remote Codes
- SPEAKER Settings
- Technical Specifications
- Licensing and Trademark Disclosures
- DTS Disclosure
- Dolby Disclosure
- Apple Disclosure
- Emotiva Disclosure
- Limited Warranty
Page 73
Speaker Placement Tips
Tips Before You Begin
Read this section thoroughly. There are a number of ways in which it may seem aesthetically
pleasing to place speakers in a room that will ultimately result in a sound quality compromise.
The placement of speakers is equally as important as the room itself. While there may be very
little you can do about the room where your home theater is installed, you can choose place-
ment of speakers within that room to maximize the sound quality of the system. Ultimately,
this will give a much better result when you are enjoying your home theater and your new
Emotiva DMC-1.
Overall, the best placement for front speakers is where the sound is directed at ear level. This
means that the speakers themselves can be in positions lower (like small floor standing speak-
ers) or higher (like in-wall or in-ceiling speakers) as long as the sound is “pointed” toward the
listeners and preferably around ear level. This is not necessarily the case with the rear speak-
ers or the side axis speakers. Read each of the sections carefully for the most appropriate
positioning. A subwoofer is also a little challenging to install depending on the room. In mul-
tiple subwoofer installations, the positioning of the woofers to the listener as well as to each
other is critical because there can be problems with cancellation if optimum placement is not
observed.