User`s guide
Table Of Contents
- TABLE OF CONTENTS
- Safety Precautions
- NEC (National Electrical Code) Standards
- A Note for the Cable Television (CATV) Installer
- Antenna Grounding Outside the House
- Thank You for your DMC-1 Purchase
- Unpacking the DMC-1
- Recording the Serial Number
- Features of the DMC-1 A/V Controller
- DMC-1 Front Panel Features
- Power Button
- IR Receiver Window
- Processor Display
- Z II (Zone 2)
- Input Select Buttons
- MODE UP/DOWN (Mode Buttons)
- AM/FM Tuner Controls
- Tone Controls
- Signal Processing Indicator Lights
- Additional Front Panel Features
- COM/RECV
- ZONE TWO POWER
- ZONE TWO ADJUST
- SIDE AXIS
- PANEL DIM Button
- MUTE Button
- DMC-1 Rear Panel Layout
- Component Video In
- Component Video Out
- Audio/Video Inputs
- Audio/Video Outputs
- Triggers and Relay
- Infrared (IR) Inputs
- RS-232 Port
- 8-CH Analog Input
- Main Audio Outputs
- XLR Audio Outputs
- Audio Inputs
- Ground Screw
- FM Antenna
- AM Antenna
- Side-Axis Outputs
- Stereo Outputs
- Audio Outputs
- IEC Line Cord Socket
- Digital Inputs
- Digital Output
- IEEE-1394 "Firewire" Port
- Installation and Connections
- AC Power Considerations
- Connection Tips for Superior Sound
- Connection Tips for Video Quality and Flexibility
- What is Composite Video?
- What is S-Video?
- What is Component Video?
- Video Up Conversion
- Video Output to the Main Screen and OSD
- Zone Specific Turn-On Triggers
- Connection Diagrams
- Connecting a DVD-Video Player (Analog Audio and Composite Video)
- Connecting a DVD-Video Player (Digital Audio and Component Video)
- Connecting to the TV or Projector using Component Video
- Connecting a VCR (Analog Audio and Composite Video)
- Connecting a CD Player (Analog Audio)
- Connecting a Cassette Tape or DAT Deck
- Connecting the 8-Channel Analog Inputs
- Connecting the AM and FM Antennas
- Connecting an Amplifier (MAIN ZONE)
- Connecting an Amplifier (ZONE 2)
- Connecting an Amplifier (ZONE 2)
- Overview of the DMC-1 Remote
- Button Layout
- Button and Display Light
- LCD Display
- DEVICE Buttons
- PAGE Button
- MAIN Button
- FAV Button
- JOYSTICK PAD
- M1, M2 and M3 Macro Buttons
- Quick Start Setup Instructions
- Adding Batteries to the Remote Control
- Quick Start Instructions for DMC-1 Setup
- Operation of the DMC-1 using the Remote
- Turning on the MAIN Zone
- Turning on ZONE 2
- Programming and Configuring YOUR Components
- P-PRO
- LEARN
- EDIT
- FAV
- PUNCH
- ERASE
- LIGHT
- MACRO
- RECAL (Recall)
- CLONE
- The On-Screen Display (OSD) Functions
- Video Connections
- OSD Activation
- Quick Access to Information
- OSD Menus
- How to Navigate the OSD Menus
- TRIM Menu
- MODES Menu
- Dynamic Range
- Pro Logic IIx Sub Menu
- DTS LFE
- DTS Neo:6
- Party
- Jazz Club Ambience
- TONE Menu
- INPUTS Menu
- INPUT CONFIGURATION MENUS (The example shows the DVD menu)
- Tuner Preset Menu
- Saving AM/FM Presets
- SETTINGS Menus
- MAIN ZONE Menu
- ZONE 2 Menu
- SPEAKERS Menu - SIZE
- SPEAKERS Menu - POSITION
- SPEAKERS Menu - CALIBRATION
- Crossover Adjustment
- Subwoofer Mode
- VIDEO Menu
- SOFTWARE Menu
- CONTROL Menu
- Special Features of the Emotiva DMC-1
- Bass Management
- Surround Modes for 2 Channel Source Material
- Surround Modes for Multi-Channel Sources
- Tuner Operation
- Recording
- Zone 2 Operation
- Speaker Placement Tips
- Tips Before You Begin
- The Front Speakers
- The Center Speaker
- Side-Axis Speakers
- The Surround Speakers
- Surround Back Speakers
- Subwoofer Location
- Remote Control Codes
- Audio Components
- Auxiliary Devices
- Cable Boxes
- CD Players
- DVD Players
- Laserdisc Players
- Satellite/DSS Receivers
- Tape Decks
- Televisions
- VCRs
- Troubleshooting Guide
- No Sound (from one or more full range speakers)
- No Subwoofer (or poor output)
- Poor AM Reception
- Poor FM Reception
- Input Selection Problems
- There is No TV Picture
- No Tone Control Functions
- No Dolby Digital or DTS Playback
- No On Screen Display
- Remote Won't Learn Commands or Codes
- Remote Not Working
- ZONE 2 Not Working
- External Amplifier(s) Shut Down (Often or Prematurely)
- DMC-1 "Locks Up" (No Response)
- Reset Procedure
- Problems Updating DMC-1 Firmware
- "Hum" Noises
- Other Probable Causes of Noise
- Favorite Settings Log
- Tone Settings
- Main Zone Settings
- Zone 2 Settings
- Mode Settings
- Control Settings
- Video Settings
- Input Settings and Remote Codes
- SPEAKER Settings
- Technical Specifications
- Licensing and Trademark Disclosures
- DTS Disclosure
- Dolby Disclosure
- Apple Disclosure
- Emotiva Disclosure
- Limited Warranty
Page 91
Control Settings
You can reference the CONTROL
SETTINGS on page 62 of this manual.
Video Settings
You can reference the VIDEO SET-
TINGS on page 61 of this manual.
Input Settings, Remote Codes, and Speaker Settings tables can be found on the next page.
VIDEO SETTINGS SELECTION
OSD VOL POP-UP
OSD SOURCE POP-UP
OSD MODE POP-UP
VIDEO DEFAULT
VID2 / MON2
VIDEO DELAY
CONTROL SETTINGS SELECTION
RS-232 PORT
REAR MAIN I/R
REAR ZONE 2 I/R
FRONT PANEL I/R