User manual

ManualsBrandsEMP-CENTAURI ManualsSAT Distributors & MultiswitchesSAT multiswitch Inputs (multiswitches): 9 (8 SAT/1 te

Dear Customer,

congratulations on the purchase of the EMP-Centauri product. Before its installation and putting

into operation, read carefully the entire operation manual. Keep the purchase and rework (if any)

records for future need.

Content

1 Field of Application, Warranty 1

2 Technical Specifications 1

3 Product Takeover 3

4 Product Storing and Installations 3

5 Product Connection 3

6 Product Settings 4

7 Safety 5

8 Product Maintenance 5

9 Troubleshooting 6

10 Symbols Explanation 6

11 Wiring Diagrams 7

12 EMP-Centauri Related Products 8

13 Contact 8

1 Field of Application, Warranty

The product is designed for the distribution of satellite (SAT), terrestrial (TERR); TV and radio

signals. We recommend the device to be installed and serviced by the qualified technician.

EMP-Centauri's PROFI CLASS products are covered under 4 (four) years warranty from the

date of purchase. The warranty shall not apply to the product used for other than the specified

purpose. The user will be responsible for injury or material damage which may arise in

consequence of any product use in contradiction with the manual. It is prohibited to dismantle

the product and make any interventions in it. Repairs or any interventions in the product may be

performed only by EMP-Centauri company, or other companies authorized by EMP-Centauri.

2 Technical Specifications

The products are standalone multiswitches for distribution of terrestrial and satellite signals from 2

satellite positions (8 polarities) to 4 (MS9/4PIU-5), 6 (MS9/6PIU-5), 8 (MS9/8PIU-5), 10

(MS9/10PIU-5), 12 (MS9/12PIU-5), 16 (MS9/16PIU-6), 20 (MS9/20PIU-6) or 26 (MS9/26PIU-6)

users. Multiswitches are controlled by DiSEqC 2.0 commands from a satellite receiver. It is enabled

to switch on active or passive mode of terrestrial band. Multiswitches are compatible with quad

LNB, it is possible to switch on or off signal 22 kHz at satellite inputs for high band. Terrestrial

input can supply terrestrial antenna preamplifier with DC voltage, the supply is electronically

protected against short-circuit. Multiswitches are powered from internal power supply P3U27.

12 EMP-Centauri's PROFI CLASS Related Products

Instruction Manual 1/003343 C

MS9/4PIU-5 V10

MS9/6PIU-5 V10

MS9/8PIU-5 V10

MS9/10PIU-5 V10

MS9/12PIU-5 V10

MS9/16PIU-6 V10

MS9/20PIU-6 V10

MS9/26PIU-6 V10

13 Contact

EMP-Centauri s.r.o.

5. kvetna 690

339 01 Klatovy 4

Czech Republic

tel: (+420) 376 314 852

fax: (+420) 376 314 367

info@emp-centauri.cz

www.emp-centauri.eu

1 of 8

8 of 8

Summary of content (4 pages)

PAGE 1
2 EMP-Centauri's PROFI CLASS Related Products Instruction Manual 1/003343 C MS9/4PIU-5 V10 MS9/10PIU-5 V10 MS9/20PIU-6 V10 MS9/6PIU-5 V10 MS9/12PIU-5 V10 MS9/26PIU-6 V10 MS9/8PIU-5 V10 MS9/16PIU-6 V10 Dear Customer, congratulations on the purchase of the EMP-Centauri product. Before its installation and putting into operation, read carefully the entire operation manual. Keep the purchase and rework (if any) records for future need.
PAGE 2
Specification Number of Inputs Number of Outputs Frequency Range Insertion Loss (avg) MS9/4PIU-5 V10 MS9/6PIU-5 V10 MS9/8PIU-5 V10 MS9/10PIU-5 V10 9 4 6 8 10 TERR 5-862 MHz (pas), 40-862 MHz (act), SAT 950-2300 MHz TERR -3/12 dB TERR -1/14 dB TERR 0/16 dB TERR 1/18 dB (act/ (act/pas), SAT 0dB (act/pas), SAT 0 dB (act/pas), SAT 0 dB pas), SAT 0 dB Isolation (min) 20 dB Maximum Input TERR 90/110 dBuV (act/pas), level* SAT 90 dBuV Maximum Output TERR 93/98 TERR 91/96 TERR 90/94 TERR 89/92 Level* dBuV (act/pas
PAGE 3
Always disconnect the product from the power grid before working on product, otherwise you risk the electric hazard. Pay attention to your safety if you have to enter places with a risk of fall. In the case the product does not work and LED of power supply is on: • Check if the terrestrial and satellite antennas are correctly fixed, optimally set and connected to the product, satellite and terrestrial receivers turned on, plugged on and correctly set. • Check the connector connections.
PAGE 4
3. Remove approx. 10 mm of the inner plastic insulation (approx. 5 mm of the insulation remains in a place). 4. Carefully screw the F connector on the cable end until the plastic insulation levels with the F connector opening. 5. Check there is no short between the inner conductor of coaxial cable and F connector. The coaxial cables shall not be broken, the minimum bending radius should be 5 cm. Connect the F connectors into the F sockets of product and fasten them with an appropriate force.