INSTRUCTION MANUAL Built-in Electric Oven EMPV-24WOC17/EMPV-24WOC12 EMPV-24WOB21 EMPV-24WOC02
DEAR CUSTOMER The oven is exceptionally easy to use and extremely efficient. After reading the instruction manual. Operating the oven will be easy. Before being packaged and leaving the manufacturer, the oven was thoroughly checked with regard to safety and functionality. Before using the appliance, please read the instruction manual carefully. By following these instructions carefully, you will be able to avoid any problems in using the appliance.
TABLE OF CONTENTS Safety instructions.....................................................................................................................3 Description of the appliance..................................................................................................6 Installation....................................................................................................................................8 Make electrical connection........................................................
SAFETY INSTRUCTIONS NOTE: Ensure there is a grounded socket nearby (behind the unit) A dedicated power circuit is recommended for the unit but not required. Additional electrical appliances on the same circuit may exceed the current (amperage) rating for that circuit. If after the installation of your unit. The circuit breaker trips or the fuse fails on a repeated basis, and then a dedicated circuit will likely be required.
!To reduce the risk of fire, do not place or install this unit in areas where the ventilation or circulation ducts may become blocked. !The unit's power cord must be connected to a properly grounded and protected,220-240V electrical outlet. Always use ground fault protection where required by the electrical code. To reduce the risk of fire, avoid running the power cord under rugs, carpets, etc. Keep the power cord away from high traffic areas where it may pose a tripping hazard.
Hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. During use the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven. WARNING: Accessible parts may become hot during use. Young children should be kept away. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
UNPACKING During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environment. All materials used for packaging the appliance are environmentally friendly; they are100% recyclable and are marked with the appropriate symbol. Caution! During unpacking, the packaging materials(polythene bags, polystyrene pieces,etc.)should be kept out of reach of children.
Baking tray X1 Grill grate (drying rack)X1 Rotisserie 7
INSTALLATION !The kitchen area should be dry and aired and equipped with efficient ventilation. When installing the oven, easy access to all control elements should be ensured. !This is a built-in oven, and its back wall and one side wall can be placed next to a high piece of furniture or a wall. Coating or veneer used on fitted furniture must be applied with a heat-resistant adhesive (215℉).This prevents surface deformation or detachment of the coating.
MAKE ELECTRICAL CONNECTION This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green(or bare)ground wire twisted together. 1. Disconnect power. 2. Feed the flexible conduit from the through the opening in the cabinet. 3. Remove junction box cover, if it is present. 4. Install a UL listed or CSA approved conduit connector to the junction box. 5. Route the flexible conduit from the oven to the junction box through a UL listed or CSA approved conduit connector.
MAKE ELECTRICAL CONNECTION Electrical Connection Options Chart 4-Wire Cable from Home Power Supply A. Cable from home power supply B. Black wires C.
MAKE ELECTRICAL CONNECTION D. 3-wire flexible conduit from oven E. Junction box F. White wires (No need connect) G. UL listed wire connectors H. Green (or bare) ground wires I. UL listed or CSA approved conduit connector 1. Connect the 2 black wires (B) together using a UL listed wire connector. 2. Connect red wire (C) together using a UL listed wire connector. 3. No need connect (F) with any wire, just with UL list wire connector. 4.
1. Connect the two black wires (C) together using a UL listed wire connector. 2. Connect the white wires from home (D) and the green (or bare) ground wire (of the oven cable) (E) using a UL listed wire connector. 3. Connect red wire (G) together using a UL listed wire connector. 4. Install junction box cover. Before first use Remove packaging, clean the interior of the oven and the hob. Take out and wash the oven fittings with warm water and a little washing-up liquid.
(3) Touch once again; finish hour set up, the minute flicker, reminding to set up. (4) Touch (5) Touch or keys, set up minutes (0-59). Defaulted “00”. key once, clock setup finish, start to work. The “:” flicker once each second. (Example: 12:30) 3. Function selection: “Roast”as example (other functions are same way to set) (1) In standby condition, touch “Roast”continuously, display shows as below diagram(“XX”means flicker, others are bright).
d. Under condition of item 3-(1) or item 3-(2) , touch key, it will work as system defaulted or current condition. Table 1(With rotisserie) Table 2(Without rotisserie) 4. Checking function (1) In working condition, touch key, can check current time, flicker 5 times it will turn to original working condition automatically. (2) In working condition, touch key, can check the time set up, flicker 5 times it will turn to original working condition automatically. 5.
once, the hour flicker, touch (1)Touch Touch again, minute flicker and touch minutes, touch or or keys, can set time between 0 and 23 hours. key, it can set up minutes between 0 and 59 key, delay setup finish. Flicker 3 times it will turn to working time, and flicker 3 times again, it will turn to clock. CLEANING AND MAINTENANCE By ensuring proper cleaning and maintenance of your cooker, you can have a significant influence on the continuing fault-free operation of your appliance.
!After cleaning the oven chamber wipe it dry Replacement of the oven light bulb In order to avoid the possibility of an electric shock ensure that the appliance is switched off before replacing the bulb !Set all control knobs to the position“OFF”/ “STOP” and disconnect the mains plug !unscrew and wash the lamp cover and then wipe it dry !unscrew the light bulb from the socket replace the bulb with a new one-a high temperature bulb (575 ℉) with the following parameters: -voltage 220~240 V~ -power 15 W -thre
!disconnect the mains plug !call the service center ! Some minor faults can be fixed by referring to the instructions given in the table below. Before calling the customer support center or the service center check the following points that are presented in the table. About circuit protection issue : 1.Sensor protection : when sensor is not connected or turnoff, display with E1;other function icons with not display ,warning with burner .