6" Top Round Adapter 3-1/4" x 10" Top Rectangular Adapter * 3 adapters and 1 top cover are included. * 1 remote control is included.
Steps To Test Run Before Installation IMPORTANT! Wear gloves to protect against sharp edges. PLEASE FOLLOW THESE INSTRUCTIONS TO TEST THE RANGE HOOD BEFORE INSTALLATION FOR ANY DEFECTS OR SHIPPING DAMAGE: 1. 2. 3. 4. 5. 6. 7. Remove the range hood and accessories from the package carefully. Place the range hood on a flat stable surface, remove the baffle filter and check for any dents or damages on the range hood body. Remove the loosen parts if there's any.
Table of Contents Important Safety Instructions 4 Installation Preparations 5 Venting Requirements Venting System Setup Duct Run Calculation Chart Electrical Requirement Installation Installing the Range Hood Connecting the Vent System Electrical Connection Installing the Baffle Filters Completing the Installation Range Hood Use Range Hood Control Panel Range Hood Care Clean the Exterior Surfaces Clean or Replace the Baffle Filters Replace the LED Lamps 5 5 6 6 7 7 8 8 8 8 9 9 10 10 10 10 Range
IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,PLEASE READ THE FOLLOWING CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,OPERATE OR MAINTAIN THE RANGE HOOD: • • • • • • • • • • Always disconnect, lock and tag the power source before installing or servicing the range hood. Failure to do so may result in fire, shock or serious injury.
INSTALLATION PREPARATIONS Venting Requirements DO DO NOT • • • • • • • • • • • • • • Have the venting system go vertically from the range hood to the roof if possible. Have 24"-30"distance between the cooktop and the range hood. 27" is recommended. Use uniformed duct of 6" round duct or 3-1/4 x 10” rectangular duct or larger. Use metal duct only. Rigid metal duct is recommended. Semi-rigid aluminum duct is also acceptable for easy connection.
INSTALLATION PREPARATIONS IMPORTANT! • • • • • Iflong duct run is needed, increase the duct size from 6" to 7" or 8" to 9". Ifa reducer is needed, use a long reducer instead of a pancake reducer and install it as far away from the range hood as possible. Reducing the duct size will restrict and decrease the speed of the airflow and hense lower the range hood's performance.
INSTALLATION This range hood series can be: • • The following steps require 2 or more people: Installed under the cabinet. or Installed on the wall without a cabinet. • 1a. Installing the Range Hood Under the Cabinet • • For installing under the cabinet with recessed bottom, attach a 4" wide wood filler strip (not provided) on each side. • Attach wood filler strips • Use a stud finder to locate and mark 2 studs inside the wall.
INSTALLATION • • • Determind the location to install the Hood. Use a stud finder to locate and mark 2 studs within the installation area. Align and securely install the Brackets to the studs. Use an extender for the Bracket if the Bracket couldn't align with the stud. • • 4. Installing the Baffle Filters • The following steps require 2 or more people: • • • Raisethe Hood between theBrackets and align the side holes with the ones on the Brackets.
RANGE HOOD USE Range Hood Control Panel • Remote Control Delayed Auto Sensor Shut Off LED When the Delayed Auto Shut Off function is activated a countdown timer will show up in the LCD display. Light • Speed Power Remote Control Sensor • • The Remote Control Sensor receives infrared (IR) signal from the remote control. ThemaximumdistanceforIRdata transmissionis 10 feet and requires direct line of sight.
RANGE HOOD CARE Cleaning • WARNING • • To reduce the risk of electrical shock, DO NOT clean the hood while it's operating. Never put your hands into the area housing the fan when the fan is operating. • • front, align and insert the filter. Pull the spring release handle and push the filter into position. Release the handle. Repeat the steps for the remaining filters.
RANGE HOOD TROUBLESHOOTING Before Calling forService Issue The range hood doesn't turn on • Possible Cause / Solution Check if the range hood is plugged in. Make sure that all power is turned on, the fuse isn't blown and all electrical wirings are properly connected. The range hood turns on but the LED light doesn't • Replace the defective LED assembly. Refer to range hood care section for instructions. The range hood vibrates when the blower is on fan.
WARRANTY This product is warrantedfor a limited periodof three years Parts, begins from the date of purchase. • This limited warranty is applied to the original retail purchaser and valid only for products purchased for homeusein thecontinental UnitedStatesof America. • This limited warranty is non-transferable and does not extend to the subsequent owners of this product.
