INSTRUCTION MANUAL 24" Single Wall Oven Empava Item #: EMPV- 24WOA16 EMPV- 24WOA01 EMPV- 24WOB14 Distributed by: Empava Appliances Inc. 15253 Don Julian Rd, City of Industry, CA 91745 USA www.empava.com Phone:+1(888)682 8882 Email:support@empava.
DEAR CUSTOMER The oven is exceptionally easy to use and extremely efficient. After reading the instruction manual, operating the oven will be easy. Before being packaged and leaving the manufacturer, the oven was thoroughly checked with regard to safety and functionality. Before using the appliance, please read the instruction manual carefully. By following these instructions carefully you will be able to avoid any problems in using the appliance.
TABLE OF CONTENTS Safety instructions........................................................................................3 Description of the appliance.........................................................................8 Installation...................................................................................................12 Operation.....................................................................................................18 Cleaning and maintenance...............................
SAFETY INSTRUCTIONS 1) Proper Installation – Be sure your appliance is properly installed and grounded by a qualified technician. 2) Never Use Your Appliance for Warming or Heating the Room. 3) Do Not Leave Children Alone – Children should not be left alone or unattended in area where appliance is in use. They should never be allowed to sit or stand on any part of the appliance. 4) Wear Proper Apparel – Loose-fitting or hanging garments should never be worn while using the appliance.
persons and animals and damage property. Important: The power supply to the appliance must be cut off before any adjustments or maintenance work is done on it. WARNING: When using this product, basic precautions should always be taken, including the following: Your built-in oven is a classified electrical appliance.
transporting or storing the unit, keep it in a dry location, free from dust, excessive vibration or other factors, which may damage the unit. !Do not operate any oven with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return oven to authorized service facility for examination, electrical or mechanical adjustment, or repaired.
WARNING: Accessible parts may become hot during use. Young children should be kept away. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass. WARNING: Ensure that the appliance is switched off before replacing the lamp, to avoid the possibility of electric shock.
UNPACKING During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environment. All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol. Caution! During unpacking, the package pieces, etc. should be kept children.
DESCRIPTION OF THE APPLIANCE EMPV- 24WOA16 Light Control Panel 1.Temperature control knob 2.Timer knob 3. Oven function selection knob 4.
EMPV- 24WOA01 Light Control Panel 1.Temperature control knob 2.Timer knob 3. Oven function selection knob 4.
EMPV- 24WOB14 Light Control Panel 1.Temperature control knob 2.Timer knob 3. Oven function selection knob 4.
Baking tray Grill grate 11
INSTALLATION Important – Save for the local electrical inspector’s use. !The kitchen area should be dry and aired and equipped with efficient ventilation. When installing the oven, easy access to all control elements should be ensured. !This is a built-in oven, and its back wall and one side wall can be placed next to a high piece of furniture or a wall. Coating or veneer used on fitted furniture must be applied with a heat-resistant adhesive (215℉).
13
MAKE ELECTRICAL CONNECTION 1. Disconnect power. 2. Feed the flexible conduit from the through the opening in the cabinet. 3. Remove junction box cover, if it is present. 4. Install a UL listed or CSA approved conduit connector to the junction box. 5. Route the flexible conduit from the oven to the junction box through a UL listed or CSA approved conduit connector. 6. Tighten screens on conduit connection. 7.
Fitting guidelines The oven is manufactured to work with signal-phase alternating current (120/240V supply system). The connection diagram is also found on the cover of the connection holder. Remember that the connection wire should match the connection type and the power rating of the oven. Before connecting the oven to the power supply it is important to read the information on the data plate and the connection diagram.
Wiring seat Bellows outlet Bellows Power cord + plug installation: The power cord + plug are installed in the factory. Rack installation diagram Step1: Insert the bracket into the mounting hole of inner tank.
Step2: Insert the bracket into the slot.
Step 2: Put the two locks into the side rack: Before first use Remove packaging, clean the interior of the oven. Take out and wash the oven fittings with warm water and a little washing-up liquid. Switch on the ventilation in the room or open a window. Heat the oven (to a temperature of 465℉, for approx,30 min.), remove any stains and wash carefully; Important! The inside of the oven should only be washed with warm water and a small amount of washing-up liquid.
Possible settings of the oven function knob (Oven lighting)By setting the knob to this position the lighting inside the oven is switched on, e.g. use when washing the oven chamber. Bake (Bottom and top heaters on) Setting the knob to the this position allows the oven to be heated conventionally. Keep Warm(Bottom heater on) When the knob is set to this position, the oven is heated using only the bottom heater. Use for, e.g. final baking from the bottom.
The oven can be switched off by setting both of these knobs to the position “0/OFF”. CLEANING AND MAINTENANCE Caution: Before each cleaning and maintenance shall be cut off the power supply! By ensuring proper cleaning and maintenance of your oven you can have a significant influence on the continuing fault-free operation of your appliance. Before you start cleaning, the oven must be switched off and you should ensure that all knobs are set to the “O”/ “OFF” position, and then cut off the power supply.
warm water with washing-up liquid. Caution! Possible moisture or water residues under the oven can result from steam cleaning ! After cleaning the oven chamber wipe it dry Replacement of the oven light bulb In order to avoid the possibility of an electric shock ensure that the appliance is switched off before replacing the bulb.
Figure 2 Figure 3 Figure 4 Method 2: (Handling with cross screwdriver) 1. To disassemble two screws on the beam with cross screwdriver, as shown in figure 5 Figure 5 2.
Figure 6 3. To move up the inside glass along with the direction of the arrow, as shown in figure 7 Figure 7 4. To sideling extract the inside glass, as shown in figure 4 Method 3: (Manual operation) 1. To insert index finger into disassembly groove and pry up inside glass, as shown in figure 8 Figure 8 2. To sideling extract the inside glass, as shown in figure 4 Disassembly and assembly method of middle glass 1. To loosen the screws on the bilateral holders, as shown in figure 9 2.
3. To put the middle glass on the corresponding holders accurately, and tighten the screws, as shown in figure 11 Figure 9 Figure 10 Figure 11 Assembly method of inside glass 1. To insert the inside glass into fixed holder and push it to the fixed position, as shown in figure 12 2.
TECHINCAL DATA Voltage rating: 240V~ 60Hz Power rating : EMPV- 24WOA16:max.2000W EMPV- 24WOA01:max.2000W EMPV- 24WOB14:max.2800W Oven dimensions H/W/D(in) :23.4/23.4/22.6 Net weight : EMPV- 24WOA16: Approx.64lb EMPV- 24WOA01: Approx.64lb EMPV- 24WOB14: Approx.