INSTRUCTION MANUAL Built-in Electric Oven EMPV-24WOA16 EMPV-24WOA01 EMPV-24WOB14 EMPV-24WOB17
DEAR CUSTOMER The oven is exceptionally easy to use and extremely efficient. After reading the instruction manual. Operating the oven will be easy. Before being packaged and leaving the manufacturer, the oven was thoroughly checked with regard to safety and functionality. Before using the appliance, please read the instruction manual carefully. By following these instructions carefully, you will be able to avoid any problems in using the appliance.
TABLE OF CONTENTS Safety instructions.....................................................................................................................3 Description of the appliance..................................................................................................7 Installation....................................................................................................................................12 Make electrical connection.......................................................
SAFETY INSTRUCTIONS NOTE： Ensure there is a grounded socket nearby (behind the unit) A dedicated power circuit is recommended for the unit but not required. Additional electrical appliances on the same circuit may exceed the current (amperage) rating for that circuit. If after the installation of your unit. The circuit breaker trips or the fuse fails on a repeated basis, and then a dedicated circuit will likely be required.
！To reduce the risk of fire, do not place or install this unit in areas where the ventilation or circulation ducts may become blocked. ！The unit's power cord must be connected to a properly grounded and protected,220-240V electrical outlet. Always use ground fault protection where required by the electrical code. To reduce the risk of fire, avoid running the power cord under rugs, carpets, etc. Keep the power cord away from high traffic areas where it may pose a tripping hazard.
Hazards involved. Children shall not play with the appliance. Children without supervision shall not make cleaning and user maintenance. During use, the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven. WARNING: Accessible parts may become hot during use. Young children should be kept away. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
UNPACKING During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environment. All materials used for packaging the appliance are environmentally friendly; they are100% recyclable and are marked with the appropriate symbol. Caution! During unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) Should be kept out of reach of children.
DESCRIPTION OF THE APPLIANCE KQP65A-16 Light CONTROL PANEL 1.Temperature control knob 2.Timer knob 3. Oven function selection knob 4.
KQP65A-01 Light CONTROL PANEL 1.Temperature control knob 2.Timer knob 3. Oven function selection knob 4.
KQP65B-14 Light CONTROL PANEL 1.Temperature control knob 2.Timer knob 3. Oven function selection knob 4.
KQB65C-17 1 Temperature control knob 2 Oven function selection knob 3 Handle 4 Clock 5 heating 6 Timer 7 Re-heat 10
Baking tray Grill grate-drying rack) Rotisserie (According to cooking function) 11
INSTALLATION ！The kitchen area should be dry and aired and equipped with efficient ventilation. When installing the oven, easy access to all control elements should be ensured. ！This is a built-in oven, and its back wall and one side wall can be placed next to a high piece of furniture or a wall. Coating or veneer used on fitted furniture must be applied with a heat-resistant adhesive (215℉).This prevents surface deformation or detachment of the coating.
MAKE ELECTRICAL CONNECTION This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green(or bare)ground wire twisted together. 1. Disconnect power. 2. Feed the flexible conduit from the through the opening in the cabinet. 3. Remove junction box cover, if it is present. 4. Install a UL listed or CSA approved conduit connector to the junction box. 5. Route the flexible conduit from the oven to the junction box through a UL listed or CSA approved conduit connector.
MAKE ELECTRICAL CONNECTION Electrical Connection Options Chart 4-Wire Cable from Home Power Supply A. Cable from home power supply B. Black wires C.
MAKE ELECTRICAL CONNECTION D. 3-wire flexible conduit from oven E. Junction box F. White wires (No need connect) G. UL listed wire connectors H. Green (or bare) ground wires I. UL listed or CSA approved conduit connector 1. Connect the 2 black wires (B) together using a UL listed wire connector. 2. Connect red wire (C) together using a UL listed wire connector. 3. No need connect (F) with any wire, just with UL list wire connector. 4.
1. Connect the two black wires (C) together using a UL listed wire connector. 2. Connect the white wires from home (D) and the green (or bare) ground wire (of the oven cable) (E) using a UL listed wire connector. 3. Connect red wire (G) together using a UL listed wire connector. 4. Install junction box cover. Before first use Remove packaging, clean the interior of the oven and the hob. Take out and wash the oven fittings with warm water and a little washing-up liquid.
shut. Preheat (Central element with fan on) this cooking mode allows homogenous distribution of the heat inside the oven, making it possible to cook several items of food at the same time. Pizza (Top heater on) When the knob is turned to this position, the oven is heated using only the top heater. Rotisserie (Fan, rotisserie and grill heater on) this cooking mode allows use of the rotisserie with grill heater.
The oven can be switched off by setting both of these knobs to the position “OFF”.
In turn on /working condition, press ,and activate to set up the function and clock, press again, start “heating time set up” ,”preheat time set up”, “current time”. After 5s, reminding to set up, and back to current time In function set up condition, press In function set up condition, press for decrease the time for increase the time About function control a、 Function selection / power on, off 1） When connect the electricity, standby status, display with 12:00 on the timer display .
“ ”or” ” to adjust heating time, after 5s no operating ,backup the revised time and exit to current time.It will heating according to the set up time ,and display with current remain heating time.You can also re-set a new heating time when in working . 2） Max heating time is 10hr, when add to max heating time, continues “ ”is invalid.
Caution! The sharp blade should always be protected by adjusting the cover (just push it with your thumb).Injuries are possible so be careful when using this instrument-keep out of reach of reach of children ! Appropriate light cleaning or washing products are recommended, such as e.g. any kind of liquids or emulsions for fat removal. In particular, special cleaning products such as COLLO Luneta, Sidol Stahlglanz ,Stahl-Fix for washing and Cleaning and Cera Fix for maintenance are recommended.
Oven light bulb Door removal In order to obtain easier access to the oven chamber for cleaning, it is possible to remove the door, To do this, tilt the safety catch part of the hinge upwards. Close the door lightly, lift and pull it out towards you. In order to fit the door back on to the cooker, do the inverse. When fitting, ensure that the notch of the Hinge is correctly placed on the protrusion of the hinge holder.
TECHINCAL DATA Voltage rating: 220-240V~ 50/60Hz Power rating: KQP65A max. 2000W KQP65B max.2800W KQB65C max.2800W Oven dimensions H/W/D (in):23.4/23.4/22.6 Net weight: KQP65A, Approx. 64LB KQP65B, Approx.71.6LB KQB65C, Approx.71.
