RANGE HOOD Installation and Operation Manual EMPAVA APPLIANCE INC. Add: 15253 Don Julian Rd, City of Industry, CA 91745 Tel: 888-682-8882 www.empava.
Dear consumer, Thanks for your purchase of our range hood and we hope we can fully satisfy all of your needs. Please read the entire instructions carefully before proceeding to obtain the best results of operation the range hood. TECHNICAL CHARACTERISTICS Model No.: EMPV-30RH05 EMPV-30RH06 Total power: 204W Motor power: 200W Led Light: 2x2W Voltage: 120V Frequency: 60Hz Filter: Steel Baffle filter Control: Touch Control EMPV-30RH05 7.46 11 .81 " " 11 .2 6 " 3" 25.98"-37.6" 10.43" 2" 34.94"-36.
MAIN PARTS NAME EMPV-30RH05 Hook Inner duct cover Outer duct cover Vent pipe Blower box Filter EMPV-30RH06 Hook Inner duct cover Outer duct cover Vent pipe Air outlet Blower box Glass Filter
INSTALLATION REQUIREMENT 1. Do not install the range hood where there are many doors ro windows in order to avoid effecting the exhaust efficiency of the hood that caused by air convection. (fig.1) 2. Install the range hood right above the cooking surface. The recommended distance between the cooking surface and the lower edge of the range hood is minimum 27.56" to maximum 31.5". (Fig.2) 3.
INSTALLATION PROCEDURES SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. Vent pipe Air outlet Step 1: Put the vent pipe to the air outlet like this picture. And use one ST3.9x10 screw to fix the vent pipe. Step 2: Matching the hook to the holes of the inner duct cover and fix it well with M4 screws. Step 3: Insert the inner duct cover into the outer duct cover.
Expanding tube 5x50 Metal Screw Hook C 200 367 A B Step5: A ccording to the size of hook key holes. Drill 3 holes in level in the wall with 10mm in diameter and 75~85mm in depth. Press the 3 expanding tube provided into the holes. Fix the hook using the 5x50 metal screw provided. Then insert three M5X50 screws to A and B And C holes to fix the hook on the wall steadily. Step 6: Hang the entire hood onto the hook, ensure the hood is level and vertical.
OPERATING INSTRUCTION 1).Electronic Switch 2). Touch Control A. Light B. Time C. Speed down D. Speed up E. Max speed F. On /off A B C D E F A: Light Press the button once to turn on the light, press again to turn off. B. Timer In standby mode, press 3 seconds, to enter into time setting mode, Press “+” set hour (0-23 circle set) and press “–” set minute(0-59), No operation within 5 seconds for automatically confirmation. When working, press once to enter into delay turn off mode for 3 minutes.
MAINTENANCE CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING WHILE THE FAN IS OPERATING. FOR THE OPTIMAL LEVEL FO OPERATION, CLEAN THE RANGE HOOD SURFACE, AN AND ALUMINUM FILTER REGULARLY. 1. Use only mild soap or detergent solutions to clean the range hood surface. Dry surfaces using soft cloth. 2. Using a stainless steel cleaner to bring the glow back into a stainless finish. 3. Clean the filter once a week or according to use status.
Do not connect the air outlet to chimney flues or combustion gas ducts Do not leave naked flames under the hood In case of any damage to power cable, replace the broken cable with a new one by qualified person. Do clean the hood correctly in accordance with instruction stated or it might cause the possibility of fire accident To replace the LED light should be undertaken by a qualified electrician or a competent person. Always use the light no more than rating.
WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high heat or when flambeing food (i.e.Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’). c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. d) Use proper pan size.
TROUBLE SHOOTING CAUTION: Disconnect the power supply before servicing. Status Cause and Method of Repairing Tools required No power Check circuit breakers If the power supply is damaged, please call for a qualified person Philips Screwdriver The motor does not run a).The motor is broken, replace motor. b). The switch control is broken, replace switch. c). The capacitor is broken, replace capacitor. Philips Screwdriver Body vibration a).
