RANGE HOOD Installation and Operation Manual EMPAVA APPLIANCE INC. Add: 15253 Don Julian Rd, City of Industry, CA 91745 Tel: 888-682-8882 www.empava.
TABLE OF CONTENTS * Warnings.......................................................P1-2 1. Features.......................................................P3 2. Main parts....................................................P4 3. Cleaning......................................................P4 4. Cleaning Maintenance..................................P5 5. Installation Maintenance...............................P6 6. Dismantling, Cleaning and Reassembly........ P9-10 7. Specification.............................
WARNING 1. Neither the importer nor the manufacturer is liable for any damage or injury caused directly or indirectly by improper installation, misuse or mis-hanging of the range hood. 2. The range hood is for general residential kitchen ventilation use only. Do not use the expel hazardous or explosive materials or vapors. 3. Disconnect all sources of electric power before installing, repairing, replacing or maintaining this appliance.
WARNING 13. Never leave any pot unattended at high heat setting on the stove. Boli-over may cause smoking and greasy spillovers may ignite fire. 14. Heat oils slowly, on low or medium heat settings. 15. Do not let children, elderly or handicapped persons use this appliance without supervision. 16. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the after sales service. 17.
1. Features EMPAVA range hoods are highly efficient and high-quality engineered - a new concept in the design of range hoods. They help keep your kitchen clean and fresh with powerful and quiet air exhaust. The fan blades are coated with Teflon that allows for the external removable stainless steel tray. Empava range hoods comes with stainless baffle filters, which may help you to eliminate weary and bothersome cleaning, The stainless filters are dishwasher safe.
2. Main parts EMPV-30RH08 Hood Body Baffle filter EMPV-30RH07 Hood Body Baffle filter 3. Cleaning One does not need to dismantle the range hood. Directly spray degreaser into the dual vane guards and vanes, let stand 3-4 minutes, and then turn on. The centrifugal force of the turbo fans will drain the grease into the oil container. To clean, simply empty the oil container.
4. Cleaning maintenance Always disconnect the power before cleaning. 1. Always use a neutral detergent to clean the surface of the hood after each use. 2. Clean both the exterior and the interior of the hood regularly, so as to keep the hood in better condition. Do not use an abrasive cleaner. 3. The fan’s baffle filters can be detached for cleaning. It must be reinstalled after cleaning. 4. The grease collection pan in the centre of the hood can be detached and cleaned regularly. 5.
Installation Height 3. The distance between the stove surface and the underside of the range hood must be in the range of 26"-30" Fig(2-A). The duct opening size is in Fig 2(B) Vent duct length 4. The length of the vent duct should be minimized to avoid air turbulence inside the duct. (Fig (2-B). Balance level: 5. The range hood must be in level during the installation. A not level installation hood may cause improper operation, leaks and oil spill over from oil collectors.
5. Installation instructions 1. Turn off the electricity on the circuit panel, use a voltmeter in order to confirm that the power source has been shut off, so as to prevent electrocution. 2. If you have to move the range to install the hood, turn off the power for the electric range, or shut off the gas to a gas stove. 3. Confirm that the distance (clearance) between the range surface and bottom of the range hood is 26"-30". (need 30" if use GAS stove.) 4.
5. Installation instructions Preparing the range hood: 1. Open the electrical knockout that is best for your wiring. 2. Fix the shutter to the range hood’s vent; prevent the leakage of oil by taping the connection with aluminum metal adhesive tape, or duct tape. 3. Attach the ruber support to the back of the range hood. 4. Unscrew and remove the range hood’s bottom cover. 5. Installation instructions Installation: 1. Pass the wiring through the electrical knockout hole in the range hood. 2.
4. Reinstall the range hood’s bottom cover and stainless steel baffle filters. 5. Reinstall the oil container. 6. Turn on the power and check the operation of the fans and light. 6. Dismantling, Cleaning and Re-assembly NOTE 1. Whenever dismantling, re-installing or maintaining the range hood, always make sure that the power ir off. 2. When dismantling, re-installing or cleaning the hood, always wear latex or rubber gloves for safety. 3. Never spill or spray water or any other liquid on or inside the motors.
Dismantling 1. First, take off the oil container and the stainless baffle filters 2. Unscrew then remove the bottom cover of the hood. 3. Turn counter-clockwise to loosen the three screws in the front right and left sides of the black base plate (oil pan), in order to remove the base plate (oil pan). 4. Remove the rubber seal. 5. Turn clockwise to remove the vane cap. 6. Pull off the vane cap.
Specifications Code Voltage Rotating method Outlet diameter Illumination Motor Power Consumption Filter Suction power Control Body size EMPV-30RH07 110V-120V/60Hz Single motor Round Vent: 6" Led light 2x2W Single motor 200W Steel baffle filter 400CFM EMPV-30RH08 110V-120V/60Hz Twin Motors Round Vent: 6" Led light 2x2W Left Right 75W 75W Steel baffle filter 400CFM 3 speed touch control 3 speed push button 29.75"x20.47"x9.45" 29.75"x20.5"x8" 8. Body size and Duct opening EMPV-30RH07 29.75" 9.45" 12.
9. Operating Instruction 1. Touch control A B C D A. Time B. Speed C. Light D. On/Off A. Timer setting: touch and hold this button 3 seconds to set time, B for hour and C for minute. B. Touch once to get high speed, touch again for middle speed and low speed. C. Touch to turn on or turn off the light. D. Touch to select on. Touch once for 1 minute delay turning off, touch again to turn off immediately. Clock setting: Clock setting: Touch and hold this button 3 seconds to enter into time setting mode.
2). Push Button Press to turn on /off the light. Press to select the high speed. Press to select the medium speed. Press to select the low speed. Press to select on/off. 10. Replacement of light Caution: 1. Make sure all control switches are off ad the range hood unplugged. 2. Use a flat head screwdriver to pop out LED light assembly. 3. Disconnect the lamp internal wires. 4. Take out the old LED light. 5. Replace with a new LED light assembly. 6.
11. Trouble shooting CAUTION: Disconnect the power supply before servicing. Status Cause and Method of Repairing Tools required No power Check circuit breakers If the power supply is damaged, please call for a qualified person Philips Screwdriver The motor does not run a).The motor is broken, replace motor. b). The switch control is broken, replace switch. c). The capacitor is broken, replace capacitor. Philips Screwdriver Body vibration a).