TABLE OF CONTENTS INTRODUCTION............................................................................................ 3 RULES FOR SAFE MARKER HANDLING............................................................... 4 QUICK SETUP............................................................................................... 5 Super Freak Barrel.......................................................................... 5 Vanquish Power On/Off..................................................................
INTRODUCTION Empire Paintball has created the finest paintball marker in the proud history of Empire products. The Vanquish is the pinnacle of intelligent marker design incorporating cutting edge technology within a proven marker platform. Hardware Features • Pressure balanced Spool Valve firing engine • Super Freak 7pc barrel kit with Carbon Fiber tip and five bore sizes (.675, .680, .685, .690, .
Rules For Safe Marker Handling IMPORTANT: Never carry your Empire Vanquish uncased when not on a playing field. The non-paintball public and law enforcement personnel may not be able to distinguish between a paintball marker and a firearm. For your own safety and for those in the area and to protect the image of the sport, always carry your Empire Vanquish in the marker case or a suitable container. Safety and safe marker handling are the most important aspects of paintball sports.
QUICK SETUP Empire Super Freak Barrel The Empire Super Freak Barrel is included with the Empire Vanquish marker. The Super Freak is a three-piece barrel that consists of a front section (tip), a back section (back) and five sized, aluminum inserts. The inserts are used to match the size of the paintball to the barrel to create the most accurate and efficient barrel system available. The threaded sections of the Super Freak have O-Rings to prevent the barrel from vibrating loose when fired.
Vanquish Power On/Off • Turn Marker ON - Press and hold the CENTER of the Directional Pad (the black button/joy stick located under the screen) until the screen illuminates to turn the board/marker ON. The Boot Up Splash Screen will display for 3 seconds. You are now in LIVE Mode (see below for more details) and the marker is ready to fire.
DE-PRESSURIZING YOUR EMPIRE VANQUISH • Make sure a barrel-blocking device is installed in/on the end of the barrel. • Turn the Empire Vanquish off using the D-Pad as explained above. • Remove loader and all paintballs from marker. • Flip the On/Off lever forward and allow the gas to vent from the regulator. • Air may remain within the marker once the regulator is vented.
battery compartment. If they don’t fit, please don’t force them as this may cause damage. Pressure and Velocity Adjustment The velocity can be adjusted by adjusting the pressure. Locate the Pressure Adjustment Screw and using the 3/32” Hex wrench, turn the screw clockwise (inward) to increase the pressure (and velocity). Turn the screw counter-clockwise to decrease the pressure. Turn on the Vanquish and enter the LIVE mode on the display (see below for more detail).
ELECTRONIC BOARD FUNCTIONS • Turn Marker ON - Press and hold the CEN TER of the Directional Pad (the black but ton/joystick located under the screen) to turn board/marker ON - You are now in LIVE Mode (see below for more details) and the marker is ready to fire.
• • • • precision electronic pressure transducer. This shows the marker pressure as regulated by the ASA/Regulator. The pressure transducer has a range of 50-250psi. Out of this range, pressure will not be displayed, and will display LOW or OVER. Shot Counter – The marker will keep track of the number of shots fired. This number will increase each time the solenoid is cycled and will be saved even when power is disconnected. Shot Counter can be reset in the settings menu.
FIRE MODE - Choose between the different firing modes • The current Firing Mode setting is displayed on the right side of the screen.
Dwell - Is the amount of time the solenoid stays on to fire a ball. Setting the Dwell too high will decrease efficiency. Setting the Dwell too low will cause inconsistent velocity. • The screen displays the current Dwell time(in milliseconds) • Press RIGHT or Press CENTER of D-Pad to change the Dwell Time (Default is 15.0 ms) • Press UP or DOWN to increase/decrease the Dwell setting (8.0-25.
Anti-Bolt Stick (ABS) Dwell - Time that the dwell is increased by for the first shot when ABS is activated. Too high of a setting may cause first shot of a string to have high velocity. Too low of a setting may cause excessive bolt stick or first shot drop off.
• Press CENTER of D-Pad to save minutes setting • Press UP or DOWN to increase/decrease the Game Timer seconds (00-59) • Press CENTER of D-Pad to save seconds setting • Press LEFT or Press CENTER of D-Pad to save settings and return to SYSTEM Menu Timer Alarm - An audible alarm sounds with 1 minute left and continuously after the timer has expired.
when the custom boot screen is turned on. • The screen displays whether the Custom Boot setting is On or Off • Press RIGHT or Press CENTER of D-Pad to change the Custom Boot setting (default is OFF) • Press UP or DOWN to switch the setting to either ON or OFF • Press LEFT or Press CENTER of D-Pad to save setting and return to SYSTEM menu Boot Time – This setting changes the amount of time the boot up splash screen is displayed when the marker is turned on.
RST Shots - Reset Shot Counter: Resets the Shot Counter when YES is selected (also available through LIVE Mode menu) • Press RIGHT or Press CENTER of D-Pad to Reset Shot Counter • Press LEFT or Press CENTER of D-Pad to reset the counter, then return to SYSTEM Menu FCTRY RST - Factory Reset: Resets all settings to factory defaults when YES is selected • Press RIGHT or Press CENTER of D-Pad for FACTORY RESET • Press UP or DOWN to cycle from NO to YES • Press LEFT or Press CENTER of D-Pad to activate RESET if
VANQUISH MENU TREE
Vanquish PC SOFTWARE The Vanquish PC Software consists of two separate applications, the Vanquish USB Tool which allows communication between the PC and Vanquish, and the Vanquish Boot Screen Editor which allows users to create custom boot screens that can be downloaded onto the Vanquish via the Vanquish USB Tool. PC Requirements: • Windows Vista, XP or 7 Operating System • Hardware requirements • 900 Mhz or faster processor • Min.
drivers. Proceed as before with steps 2-5 to install. Using the Vanquish USB Tool Software Windows Vista Manual Install: 1. After connecting the Vanquish to the USB port the New Hardware Found window will appear. 2. Select “Locate and install driver software (recommended)”. 3. When windows asks for the disk select “I don’t have the disc, Show me other options”. 4. Windows will say it could not find driver software. Click “Browse my computer for driver software”. 5.
How to Save Settings to PC Click Save Settings and follow the prompt to save the current settings from the Vanquish USB Tool. Configuration 1, 2, 3 and System settings will be saved on the PC. The file format is .txt so it may be edited outside of the Vanquish USB Tool. How to Load Settings from PC Click “Load Settings” and follow the prompt to open and load a Vanquish settings file into the Vanquish USB Tool software. Click “Sync Settings” to sync the loaded settings with the Vanquish.
Vanquish Boot Screen Editor Software The Vanquish Boot Screen Editor allows you to make your own custom graphics that can be loaded onto you Vanquish Paintball marker using the Vanquish USB Tool software. These graphics can be displayed when you turn on the Vanquish to make your Vanquish unique to you. The Vanquish Screen is 128 pixels high by 32 pixels wide. The Boot screen editor gives you access to each individual pixel.
The Status Bar Says “Com Error 1…” or “Com Error 2…” - On the Vanquish, disconnect the USB Port and disconnect the battery. Then re-connect battery and then the USB Cable in that order. Click Connect to attempt the connection again. The Status Bar Says “Flash Error 1…” or “Flash Error 2…” - On the Vanquish, disconnect the USB Port and disconnect the battery. Then re-connect battery and then the USB Cable in that order. Click Connect to attempt the connection again.
Maintenance of Firing Engine 4. Unscrew the Bolt Guide from the Back Cap. Remove old grease and debris from Firing Engine. 2. Unscrew the Air Guide by turning the Air Guide counter-clockwise to remove from the Back Cap. The Bolt Spring will come out with the Bolt Guide. 5. Wipe the parts down with a clean rag removing any old grease or debris. 6. Inspect the O-Rings on both the bolt and Air Guide for any wear or damage. Replace dam aged or worn O-Rings if necessary. 7.
9. Apply grease to the two small O-Rings on the Rod #8a, #8b. Firing Engine O-Ring Guide 1 Air Guide O-ring - UR 020/70 (72558) 2 Air Guide (Internal) O-ring - UR 017/70 (72556) 3 Back Cap O-ring - BUNA 019/70 (72557) 4 Back Cap O-ring - UR 020/70 (72558) 5 Back Cap (Internal) O-ring - UR 017/70 (72556) 6 7 8 9 10 Bolt O-ring - BUNA 015/90 (72549) Bolt O-ring - UR 016/70 (72555) Rod O-ring - UR 013/70 (72552) Rod O-ring - UR 014/20 (72553) Rod O-ring - BUNA 015/70 (72554) 10.
• Carefully remove the Eye Board from the body • Use a Q-tip to remove any paint or debris from the Eye Board and the Eye cavity of the Body • Ensure that the opening in front of the Eyes is clear and that the laser has a clear path to the opposite Eye. • Inspect the Ball Detents, faulty or worn out Ball Detents can cause double feeding or ball breaks • Clean or replace as necessary • Re-install the Eye Board and Eye Cover.
TROUBLESHOOTING GUIDE PROBLEM SOLUTION MARKER LEAKS Clean and Lubricate the Firing Engine as described in this manual Check the Regulator pressure using the on screen read out and ensure the pressure is below 200psi. Check O-ring on outside of Air Guide, 4th from the front of the marker (Firing Engine Diagram #1d).
My ASA/regulator does not always instantly deUse 3-4 drops of paintball marker oil in the ASA/regulator where the tank is screwed in. Apply air to marker and pressurize when I turn the lever off cycle the marker to work the oil through. For more advanced regulator issues please contact paintballsolutions.com. Advanced regulator service is recommended only by certified persons.
Diagram # SKU Part Descrip2on BARREL 1 2 3 4 5 5 5 5 5 72621 72508 72622 72488 11520 11521 11522 11523 11524 Diagram # SKU FEEDNECK 6 7 8 9 10 11 12 72571 72573 72572 72489 72570 72497 72496 SUPER FREAK CARBON/ALU TIP -‐ BLACK (16950) O-‐RING BUNA-‐N 70 DUR -‐018 (.739 ID) SUPER FREAK BACK AC -‐ POLISH BLACK (16950) O-‐RING BUNA-‐N 70 DUR 1MM CS X 19.5MM ID INSERT .675 INSERT .680 INSERT .
Diagram # FEEDNECK 6 7 8 9 10 11 12 Diagram # FIRING ENGINE 13 14 15 16 17 18 19 20 21 22 23 24 25 26 SKU 72571 72573 72572 72489 72570 72497 72496 SKU 72556 72558 72567 72564 72565 72552 72568 72553 72549 72557 72566 72563 72555 72569 Part Description FEEDNECK LEVER - DUST BLACK (16950) FEEDNECK LEVER BUSHING FEEDNECK - POLISHED BLACK (16950) O-RING BUNA-N 70 DUR -006 (.114 ID) FEEDNECK THUMB SCREW SCREW BHCS 8-32 X 1.000 SCREW BHCS 8-32 X .750 Part Description O-RING URETHANE 70 DUR -017 (.
Diagram # GRIP FRAME 30 37 51 53 54 55 56 57 59 60 61 62 TRIGGER 34 49 50 52 Diagram # FOREGRIP 43 44 45 46 47 48 SKU Part Descrip2on 72515 72517 72511 72588 72584 72585 72590 72584 72589 72516 72586 72550 SCREW BHCS 8-‐32 X .250 SCREW SHCS 5-‐40 X .250 SCREW SHSS 3/16 DIA 3/8 LG 8-‐32 X .250 GRIP FRAME -‐ DUST BLACK (16950) MAGNET 8MM DIA .
Diagram # REGULATOR 9 34 51 63 64 65 66 67 68 69 70 71 72 74 75 76 77 78 79 80 81 82 83 84 85 86 87 SKU 72489 72513 72512 72615 72609 40916 72610 72604 72605 72597 72614 72613 72601 72598 72599 72490 72651 72509 72602 72612 72606 72607 72611 72608 72595 72596 17597 Part Description O-RING BUNA-N 70 DUR -006 (.114 ID) SCREW SET 10-32 X .250 CP SCREW SHSS 3/16 DIA 3/8 LG 8-32 X .250 HP REGULATOR CAP - DUST BLACK (16950) REGULATOR DISK O-RING BUNA-N 70 DUR -017 (.
Empire Paintball 11723 Lime Kiln Rd. Neosho, MO 64850 www.empirepaintball.com Empire Paintball is a brand of KEE Action Sports, LLC. PATENT(S): See www.paintballsolutions.com/patents © 2012-2013 KEE Action Sports. All rights reserved. This KEE Action Sports product is protected by one or more United States patents. KEE Action Sports Trademarks, Designs and Copyrights are protected by one or more United States patents and International Law.
EMPIREPAINTBALL.COM 11723 Lime Kiln Rd, Neosho, MO 64850 800-220-3222 Empire Paintball is a brand of KEE Action Sports, LLC.