User Manual WAP655-C Version 1.
IMPORTANT ToinstallthisAccessPoint Please refer to the QuickInstallationGuideincluded in the product packaging 1
Chapter1 ProductOverview 2
Introduction Key Features ・Built-in Turbo Engine with Quad-Core powerful chipset to process multiple tasks for driving and enhancing performance effectively. ・Support 802.11ac Wave 2.0 technology to enhance bandwidth and connecting speed. ・Dual radio 2x2 802.11 ac/a/b/g/n AP, support up to 867 Mbps in 5GHz frequency band and 400 Mbps in 2.4GHz frequency band (with 2ss/VHT40 clients) ・RF circuity is designed and tuned for improved transmit and receive wireless coverage. ・Compliance with 802.
Physical Interface (WAP655-C) 4
Physical & Environment Power Source PoE: compatible with 802.3af/at Internal High Gain Antenna ~3.55dBi 2.4GHz antennas (Peak Gain) ~5.7dBi 5GHz antennas 1 x 10/100/1000Mbps Ethernet Port with 802.3af/at PoE Interface 1x 10/100/1000Mbps Ethernet Port 1 x reset button Dimensions (W x D x H) 300x181x34.
Applications Wireless LAN (WLAN) products are easy to install and highly efficient. The following list describes some of the many applications made possible through the power and flexibility ofWLANs: Difficult-to-Wire Environments: There are many situations where wires cannot be installed, deployed easily, or cannot be hidden from view.
Chapter2 Before YouBegin 7
Computer Settings Windows XP/Windows 7/Windows 8/Windows 10 1b. Move your mouse to the lower right hot corner to display the Charms Bar and select the Control Panel in Windows 8OS. In order to use the Access Point, you must first configure the TCP/IPv4connectionofyourWindowsOScomputersystem. 1a. Click the Start button and open the Control Panel Windows 8 1c. In Windows10, click Start to select All APP stoenter the folder of Windows system for selecting Control Panel.
4. Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties. 2a. In Windows XP, click Network Connections. 2b.In Windows7/Windows8/Windows10, click View Network Status and Tasks in the Network and Internetsection, then select Change adapter settings. 3. Right click on Local Area Connection and select Properties. 5. Select Use the following IP address and enter an IP address that is different from the Access Point and Subnet mask, then click OK.
Note: EnsurethattheIPaddressandSubnetmaskare on the same subnet as the device. For example: WAP655-C IP address: 192.168.1.1 PC IP address: 192.168.1.2–192.168.1.255 PC Subnet mask: 255.255.255.
Apple Mac OSX 4. In Configure IPv4, select Manually. 1. Go to System Preferences (Which can be opened in the Applications folder or selecting it in the Apple Menu). 5. Enter an IP address that is different from the Access Point and Subnet mask then press OK. 2. Select Network in the Internet & Network section. Note: Ensure that the IP address and Subnet mask are on the same subnet as the device. For example: A device IP address: 192.168.1.1 PCIPaddress: 192.168.1.2–192.168.1.255 PCSubnetmask:255.255.
Chapter 3 Configuring Your Access Point 12
ConfiguringYourAccessPoint This section will show you how to configure the device using the web-based configuration interface. 2. The default username and password are admin. Once you have entered the correct user name and password, click the Login button to open the web-base configuration page. Default Settings Please use your Ethernet port or wireless network adapter to connect the Access Point. IP Address 192.168.1.1 Username / Password none Web Configuration 1.
Chapter4 Building aWireless Network 14
Before starting to configure this Access Point, you may realize the used scen a rounder varied operating modes. The AP has the ability to operate in various modes. This chapter describes purpose of different operating modes and lists down the operating modes for outdoor Access Points or Client Premise Equipments(CPE). Access Point Mode In Access Point Mode, AP be have slikes a central connection for stations or clients that support IEEE802.11ac/a/b/g/n networks.
Client Bridge Mode The Access Point essentially acts as a wireless adapter that connects to an access point to allow a system of wireless access to the network in the Client Bridge mode. Since the computers are on the same subnet, the Access Point can broadcast or each all enddevices. If you use the client bridge mode in this Access Point, you can use the AP Detection feature to scan for Access Points within range.
The AP can be used as a centralized Outdoor Access Point with which other Wireless 802.11b/g/n2.4 or ac/a/n 5GHz Outdoor Client Bridge scan associate; leveraging the long-range capability of their internal high-gain directional antennas, resulting in a very costeffective solution to expand a company network over a multiple building campus. ENH202 Client Bridge ENH202 AP Access Point Client 2.
WDS APMode The AP also supports WDS AP mode. This operating mode allows wireless stations to connect with Access Point via using WDS technology. In this mode, configure the MAC addresses or SSIDs in both Access Points to enlarge the wireless area by enabling WDS Link settings. WDS AP mode supports up to four(4) AP MAC addresses and four(4) SSIDs at the same time. AP WDS AP AP WDSAP 5GHz 5 GHz Client Computer 2.
WDS Bridge Mode In WDS Bridge Mode, the Access Point can wirelessly connect different LANs by configuring the MAC address and security settings of each Access Points. Use this operating mode when two wired LANs located as mall distance apart want to communicate with each other. The best solution is to use the Access Point to wirelessly connect two wired LANs, as shown in the following diagram. WDS Bridge Mode can establish up to four (4) to eight (8) WDS links, creating a star-like network.
WDS Station Mode WDS station(WDS STA) mode expands the WDS by receiving a wireless signal/service and sharing it through the Ethernet port. With WDS STA mode, Access PointWDS AP on both 5 GHz or 2.
Chapter5 Status 21
Overview Note: VLAN ID is only applicable in Access Point, WDS AP or WDS BR mode. SaveChanges This page lets you save and apply the settings shown under Unsaved changes list, or Revert the unsaved changes and revert to the previous settings that were in effect. • Device Status Clicking the Device Status link under the Overview menu shows the status information about the current operating mode.
• The LAN Information section shows the Local Area Network settings such as the LAN IP Address, Subnet mask, Primary DNS Address , Secondary DNS Address, status of DHCP client, and status of Spanning Tree protocol (STP). The Wireless LAN Information 2.4 GHz/5 GHz section shows wireless information such as Operation Mode, Frequency, and Channel.
Connections Realtime 2.4 GHz/5 GHz Connection List Realtime Click the connection link under the Overview menu displays the connection list of clients associated to the AP’s2.4 GHz/5 GHz, along with the MAC addresses and signal strength for each client. Clicking Refresh updates the client list. The Realtime section contains the following options: Note: Only applicable in Access Point and WDS AP modes. 2.4 GHz/5 GHz WDS Link List Click the connection link under the Overview menu.
Chapter6 Network 25
Basic IPv4/IPv6 Settings This page allows you to modify the device’s IP settings. IP Network Settings: Select whether the device IP address will use a static IP address specified in the IP address field or be obtained automatically when the device connects to a DHCP server. IP Address: The IP address of this device. Subnet Mask: TheIP Subnet mask ofthis device. Gateway: The Default Gateway of this device. Leave it blank if you are unsure of this setting.
Chapter7 2.
Wireless Devices to network to the 2.4GHz band only if the client devices are not currently associated on 2.4GHz radioin this AP. Wireless Settings *Prefer 5GHz: When band steering is configured to Prefer 5GHz mode, the AP will steer dual band capable client devices to 5GHz radio when the RSSI value of these client devices on 5GHz radio is more than set one. The allowed RSSI value for default setting is -75dBm. Device Name: Enter a name for the device. The name you type appears in SNMP management.
This page displays the current status of the Wireless settings of this AP. Operation Mode: Scrow down this list to select operation modes for implementing on this radio. The default operation mode is Access Point on base stations and Access Points and is Client Bridge on Client Premise Equipements(CPE). Meanwhile, the outdoor devices also support WDS modes for peer to peer or peer to multi-peer connections. 2.
Channel HT Mode: Scrow down this list to select bandwidth for operating under a frequency band. The default channel bandwidth is 20MHz on 2.4GHz frequency radio and 40 MHz on 5GHz frequency radio. Considering the different applications ,users can decide to implement a channel bandwidth to fulfill real applications. The larger the channel, the greater the transmission quality and speed. Transmit Power (Tx Power): Default Tx power is Auto to obey regulartory power of each country.
*Default configuration: Default setting of channel selection is Associated client devices will be restricted at this number. “All” to perform auto channel on the exist channel list. Aggregation: Integrate multiple data packets into one packet to deliver to client devices. This option reduces the number of packets, but also increases packet sizes. *None: Click “None” to disable the setting on this radio. This radio is disabled.
SSIDs (eight (8) per band). If multiple client devices will be accessing the network, you can arrange the devices into SSID groups. Click Edit to configure the profile and check whether you want to enable extra SSID. 2.
Enable: Click this check box to enable this SSID interface. The default SSIDs are enable on the both first 2.4GHz and 5GHz SSID. SSID: Specifies the SSID for the current profile. Hidden SSID: Check this option to hide the SSID from clients. Ifchecked, theSSIDwillnotappearinthesitesurvey. Client Isolation: Click the appropriate radio button to enable this function for allowing or preventing communication between client devices. VID: Specifies the VLAN tag for each profile.
InputType: ASCII: Regular Text (recommended) Hexadecimal Numbers (For advanced users) Wireless Security The Wireless Security section lets you configure the AP’s security modes Key Length: Select the desired option and ensure that wireless clients use the same setting. Your choices are 64, 128, and 152-bit password lengths. Secuirty Mode: Including WEP, WPA-PSK, WPA2-PSK, WPAPSKMixed,WPA,WPA2,andWPAMixed.Westrongly recommendyoutouseWPA2-PSKmode. Default Key: Select the Key you wish to be the default.
*SettingofWPA-PSK,WPA2-PSKandWPA-PSKMixed (Pre- * Setting of WPA-Enterprise & WPA2-Enterprise (Pre- SharedKey): Shared Key): Encryption: You may select AES, TKIP or Both(TKIP+AES) to be the encryption type you would like. Please ensure that your wireless clients use the same settings. Encryption: Select the WPA encryption type you would like. Please * ensure that your wireless clients use the same settings.
RadiusSecret:Enterthesecretrequiredtoconnecttothe Radiusserver. Radius Accounting: Enable or disable accounting feature. Radius Accounting Server: Enter the IP address of the Radius accountingserver. RadiusAccountingPortEntertheportnumberusedfor connectionstotheRadiusaccountingserver. RadiusAccountingSecret:Enterthesecretrequiredto connect to the Radius accounting server. InterimAccountingInterval:Specifieshowoften,in seconds, the accounting data sends. Note: 802.
Wireless MAC Filtering Add:ClickAddtoaddtheMACaddresstotheMACaddress table. WirelessMACFilteringisusedtoallowordenynetwork accesstowirelessclients(computers,tabletPCs,NAS, smartphones,etc.)accordingtotheirMACaddresses.You Delete: Delete the selected entries. Save: Click Save to apply the changes. canmanuallyaddaMACaddresstorestrictpermissionto accessthisAP.Thedefaultsettingis:DisableWireless MACFilter. Note: OnlyapplicableinAccessPointandWDSAP modes.
WDS Link Settings 2.4 GHz/5 GHz WDS Link Settings UsingtheWDS(WirelessDistributionSystem)featurewill allowanetworkadministratororinstallertoconnectto AccessPointswirelessly.Doingsowillextendthewired infrastructuretolocationswherecablingisnotpossibleor inefficient toimplement. Note:Compatibilitybetweendifferentbrandsand models of Access Points is not guaranteed. It is recommendedthattheWDSnetworkbecreatedusing thesamemodelsformaximumcompatibility.
Account Firmware This page allows you to change the AP usernameand password.Bydefault,theusernameis:adminandthe passwordis:admin.Thepasswordcancontainfrom0to 12alphanumericcharactersandiscasesensitive. Firmware Upgrade Thispageallowsyoutoupgradethefirmwareofthe AP. Account Settings To Perform the FirmwareUpgrade: 1. ClicktheChooseFilebuttonandnavigatetheOSfile systemtothelocationoftheupgradefile. 2. Selecttheupgradefile.Thenameofthefilewillappear intheUpgradeFilefield. 3.
Backup/Restore Backup Setting: Click Export to save the current configured settings. This page allows you to save the current device configurations.Whenyousaveyourconfigurations, youalsocanreloadthesavedconfigurationsintothe devicethroughtheRestoreSavedSettingsfromafile section.Ifextremeproblemsoccur,orifyouhaveset theAPincorrectly,youcanusetheResetbuttoninthe ReverttoFactoryDefaultSettingssectiontorestore alltheconfigurationsoftheAPtotheoriginaldefault settings.
Back Up Setting as Default: Click Backup to backup theusersettingsyouwouldliketothedevice’smemory forthedefaultsettings. User Setting Thefunctionallowsyoutobackupthecurrentdevice configurationsintotheAPasthedefaultvalue.If extremeproblemsoccur,orifyouhavesettheAP incorrectly,youcanpushtheResetbuttontorevertall theconfigurationsoftheAPtotheuserdefault. RestoretoUserDefault:ClickRestoretorestoreuser settings to the factory standard settings.
Log System Log TheAPautomaticallylogs(records)eventsofpossible interestinitsinternalmemory.Toviewthelogged information,clicktheLoglinkundertheSystemManager menu.Ifthereisnotenoughinternalmemorytologall events,oldereventsaredeletedfromthelog.When powereddownorrebooted,thelogwillbecleared.
Logout Logout:ClickLogout inManagementmenutologout. Reset Insomecircumstances,itmayberequiredtoforcethedevicetoreboot.ClickonReset toreboottheAP. Onceyouclickresetbutton,youwillseetheoptionsforreboot or restore this AP. Rebootthedevice:Clickittorebootthisdevice. RestoretoFactoryDefault:Clickittoresetthisdevicetofactory defaultsetting. RestoretoUserDefault:Clickittoresetthisdeviceto userdefaultsettings.
Appendix A - FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix B - IC Interference Statement Industry Canada Statement This device complies with Canada license-exempt RSSs of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme RSS Canada sans licence d’Industrie Canada applicable aux appareils radio exempts de licence.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 21cm de distance entre la source de rayonnement et votre corps. Industry Canada Warning This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit repond aux specifications techniques applicables a l'innovation, Science et Developpement economique Canada.
Appendix C - CE Interference Statement Europe – EU Declaration of Conformity • EN60950-1 Safety of Information Technology Equipment • EN50385 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz) • EN 300 328 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using sp
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz.
Latviski [Latvian] Lietuvių [Lithuanian] Nederlands [Dutch] Malti [Maltese] Magyar [Hungarian] Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Svenska [Swedish] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type o f equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
