MUTE POWER TV/CATV PICTURE SWAP SOUND TV VIDEO COMP. PC WIDE PIP POP DIGEST - + DISP V-CHIP ATSC FAV- ZOOM WINDOW C.C. MTS SET UP EPG C.C.
Federal Communications Commission Statement 1. Reorient/Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit which is different from what the receiver is connected to. 4. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user authority to operate the equipment.
Warnings and Precautions To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment. Before operating this equipment, please read this manual completely, and keep it nearby for future reference. WARNING This symbol is intended to alert the user to avoid the risk of electric shock. This equipment must not be disassembled by anyone except qualified service personnel.
Remove the plug from the wall outlet, if the equipment will not be used for a long period of time. ▪ Do not place, use or handle this equipment near water. ▪ Never expose the equipment to liquid, rain, or moisture. Seek for service if any of the above is spilled into the equipment. ▪ Do not expose the equipment to extreme temperature or to direct sunlight, as the equipment may heat up and suffer damage.
Outdoor Antenna Safety Instructions If an outdoor antenna is connected, follow the precautions below: ▪ An outdoor antenna should not be located in any area where it could come in contact with overhead power lines, or any other electric light or power circuits. ▪ When installing an outdoor antenna system, extreme caution should be taken to prevent contact with power lines. Direct contact with power lines may be fatal and should be avoided at all costs.
CONTENTS ENGLISH Federal Communications Commission Statement Warnings and Precautions Important Safety Instructions ......................................................................................... 2 Antenna Safety Instructions ........................................................................................... 4 Chapter 1 Introducing the LCD TV Key Features .................................................................................................................
6 Chapter 1 Introducing the LCD TV
Chapter 1 Introducing the LCD TV Key Features ENGLISH Various Audio/Video terminals for external equipment connection ▪ ▪ ▪ ▪ ▪ ▪ ▪ 2 composite A/V input terminal 1 set of composite A/V output terminals 2 S-VIDEO terminal 2 set of component Video input terminals 1 VGA/AUDIO input terminal 1 HDMI/AUDIO input terminal 4 sets of Audio input terminals High Definition Multimedia Interface (HDMI) ▪ High Definition Multimedia Interface (HDMI) is a small, user-friendly interconnect that can carry up to 5 Gbps of
Package Contents Make sure all of the following contents are included. If you are missing any items, please return this product to the original place of purchase. LCD TV Warranty Card Remote Control/AAA Batteries x 2 User Guide MUTE POWER TV/CATV PICTURE SWAP SOUND TV VIDEO WIDE COMP. PC POP DIGEST PIP - + DISP V-CHIP ATSC SET UP FAV- FAV+ ZOOM WINDOW C.C. MTS EPG C.C.
Setting Your LCD TV Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT. terminal (refer to page14-17). ENGLISH Connect the AC power cord at the back of the TV and connect t the power cord to wall outlet. Insert the 2 batteries supplied in remote control. Step1 Slide the back cover up to open the battery compartment of the remote control. Step2 Insert two AAA size batteries.
Your LCD TV Front/Side View and Controls LED The LED light indicates when the LCD TV is activated. IR Infrared Receiver MENU Press once to display the OSD (on screen display), press again to turn the OSD off. VOLUME▲▼ Adjusts the volume up and down. Selects the main-menu item and change values for items when in the OSD mode. SELECT▲▼ Scans up and down through channels. Selects submenu item when in the OSD mode. SOURCE Chooses from different input signal sources.
Rear View and Jacks ENGLISH ANT. NTSC Connects RF input from VHF/UHF antenna or cable. ANT. ATSC Connects RF input from VHF/UHF antenna or cable to receive high definition digital television. AV2/S-VIDEO2 IN Connects to the composite Video/S-VIDEO and Audio output jacks on external video equipment. AV Output Connects to the composite A/V intput jacks on external video equipment. AV1/S-VIDEO1 IN Connects to the composite Video/S-VIDEO and Audio output jacks on external video equipment.
Your Remote Control PICTURE Cycles through picture quality modes: STANDARD, BRIGHT, SOFT, MOVE STANDARD, MOVE BRILLIANT MUTE Mutes and restores your LCD TV sound. TV/CATV Cycles through the TV receiving signal: TV(antenna), CATV(cable) WIDE Cycles through the picture size:16:9,4:3, FULL,NATIVE -+ Changes the size of secondary picture while using the window button. DISP Displays information on the LCD TV screen such as channel and channel label. V-CHIP Turns the V-CHIP function on and off.
ATSC DTV FUNCTION POWER TV/CATV PICTURE SWAP SETUP In ATSC TV mode, pressing SETUP displays the menu on the screen. ATSC Select the ATSC TV receiving the signal inputs of your LCDTV. FAV-/FAV+ Change the favorite channel up and down. ENGLISH MUTE SOUND TV VIDEO COMP. PC WIDE PIP POP DIGEST - + DISP V-CHIP C.C. MTS ATSC SET UP EPG C.C. FAV- FAV+ FAV EDIT ZOOM WINDOW EPG In ATSC TV mode, pressing EPG displays the EPG (Electronic Program Guide) on the screen. C.C.
Chapter 2 Installing the LCD TV Refer to the owner’s manual of any external equipment to be connected. When connecting any external equipment, do not connect any AC power cords to wall outlets until all other connections are completed. Connecting a TV Cable or Antenna Antenna Connection The antenna requirements for good color TV reception are more important than those for a black & white TV reception. For this reason, a good quality outdoor antenna is strongly recommended.
A. Combination VHF/UHF antenna VHF/UHF Antenna 300-ohm twinlead cable VHF/UHF Antenna ENGLISH 300/75-ohm adapter (not included) 75-ohm coaxial cable ANT. UHF Antenna B. Separate VHF and/or UHF antennas Combiner 300-ohm twin(not included) lead cable OUT IN VHF Antenna 75-ohm coaxial cable 300-ohm twinlead cable ANT.
Cable TV (CATV) Connection This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building accurately, or as close to the point of cable entry as possible.
Use a supplied antenna cable to connect the ANT.NTSC or ANT.ATSC signal to the LCD TV’s ANT. terminal. ENGLISH NTSC ATSC Connect the AC power cord at the back of the TV and connect the power cord to wall outlet. Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time.
Connecting a VCR AV2 HDMI VGA Pb Pr Pb Pr VIDEO S-VIDEO1 AV1 NTSC A S-VIDEO2 ATSC B METHOD A: Use an S-Video cable to connect the VCR’s S-video output jack to the LCD TV’s SVIDEO1 or S-VIDEO2 input jack. Use an audio cable to connect the VCR’s audio output jacks to the LCD TV’s audio inputs. METHOD B: Use a composite cable to connect the VCR’s composite video/audio jacks to the LCD TV’s composite video/audio AV1 or AV2 jacks.
Connecting a DVD Player ENGLISH AV2 HDMI VGA Pb Pr Pb Pr S-VIDEO2 VIDEO S-VIDEO1 AV1 NTSC ATSC /Pb /Pr A C B D /Pb /Pr METHOD A: DVD PLAYER Use a HDMI cable to connect the DVD’s HDMI jack to the LCD TV’s HDMI jack. METHOD B: Use a component cable to connect the DVD player’s component output jacks to the LCD TV’s component (YPbPr1 or YPbPr2) input jacks. Use an audio cable to connect the DVD player’s component audio jacks to the LCD TV’s audio input jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To watch a DVD, press the PC button on the remote repeatedly to select HDMI ( METHOD A), or press the COMP. button on the remote repeatedly to select YPbPr1/YPbPr2 ( METHOD B), or press the VIDEO button on the remote repeatedly to select S-VIDEO1/ S-VIDEO2( METHOD C), or AV1/AV2(METHOD D).
Connecting a TV Cable Box and Satellite Receiver ENGLISH AV2 HDMI VGA Pb Pr Pb Pr S-VIDEO2 VIDEO S-VIDEO1 AV1 NTSC ATSC /Pb /Pr A B /Pb /Pr METHOD A: Use a component cable to connect the satellite receiver’s component (YPbPr1) output jacks to the LCD TV’s component input jacks. Use an audio cable to connect the satellite receiver’s component audio jacks to the LCD TV’s audio input jacks.
22 Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. To watch programs via satellite receiver, press the COMP. button on the remote repeatedly to select YPbPr1. To watch TV via TV cable box, press the PC button on the remote repeatedly to select VGA ( METHOD A), or press the VIDEO button on the remote repeatedly to select S-VIDEO1 ( METHOD B).
Connecting a Video Camera ENGLISH AV2 HDMI VGA Pb Pr Pb Pr VIDEO S-VIDEO1 AV1 NTSC A S-VIDEO2 ATSC B METHOD A: Use an audio cable to connect the video camera’s audio output jacks to the LCD TV’s audio inputs. Use an S-Video cable to connect the video camera’s S-video output jack to the LCD TV’s S-VIDEO1 or S-VIDEO2 input jack. METHOD B: Use a composite cable to connect the video camera’s composite video/audio jacks to the LCD TV’s AV1 or AV2 jacks.
Connecting two VCRs AV2 HDMI VGA Pb Pr Pb Pr S-VIDEO2 VIDEO S-VIDEO1 AV1 NTSC ATSC 2 1 Use a composite cable to connect the VCR1’s composite video/audio input jacks to the LCD TV’s composite video/audio output jacks. Use a composite cable to connect the VCR2’s composite video/audio outputjacks to the LCD TV’s AV2 input jacks. Connect all AC power sources, before turning the LCD TV’s power switch on. Press the button on the remote to turn on your LCD TV.
Connecting a PC ENGLISH AV2 HDMI VGA Pb Pr Pb Pr S-VIDEO2 VIDEO S-VIDEO1 AV1 NTSC ATSC Use a D-SUB cable to connect the PC’s D-SUB output jack to the LCD TV’s VGA input jack. Use an audio cable to connect the PC’s audio output jacks to LCD TV’s. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. Press the PC button on the remote repeatedly to select VGA.
Chapter 3 USING THE FEATURES Watching Your LCD Press the button to turn the LCD TV on. Press the TV button to enter TV mode, or press the SOURCE button on the top of TV to select the TV. Press the CH+- buttons to change channels, or use the 0-9 buttons to choose a channel. The one/two digit numbers by pressing 00 button. Press the CH RTN button to alternate back and forth between two channels. 1 SOUND TV VIDEO COMP. PC WIDE PIP POP DIGEST 2 - + DISP V-CHIP C.C.
Operating the Menu Press the button to turn the LCD TV on. ENGLISH To select the signal source, press the MENU button on the remote control. The main menu will appear on the screen. Use the VOL+- buttons to select your main menu option.
DISPLAY MENU: MAIN MENU : DISPLAY DISPLAY MODE: MAIN SOURCE: SUB SOURCE: SWAP MENU SELECT H POSITION V POSITION FULL TV VGA ► ► ► : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT OSD MENU: MAIN MENU : OSD LANGUAGE TRANSPARENCY OSD TIME OUT ENGLISH 8 15 SEC : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT MISCELLANEOUS MENU: MAIN MENU : MISC SLEEP ASPECT RATIO NOISE REDUCTION IMAGE FREEZE CCD TYPE CCD : SELECT MENU : EXIT OFF FULL MEDIUM OFF CC1 OFF : SELECT ITEM ENTER: NEXT TV SET MENU: MAIN MENU :
Setting up the Channel List Automatically scans and stores all the TV channels With the LCD TV connected to a television programming source, press the TV button on the remote control. Press the MENU button on the remote control to display the Main menu, and use the VOL+- buttons to select the TV SET, and press the ENTER button.
Hiding the TV channels Press the MENU button on the remote control to display the Main menu, and use the VOL+- buttons to select the TV SET, and press the ENTER button. Press the CH+- buttons to select CHANNEL, then press the VOL+- to select the channel you choose to hide.
Setting the Favorite TV channels Press the MENU button on the remote control to display the Main menu, and use the ENGLISH VOL+- buttons to select the TV SET, and press the ENTER button.
Customizing the Picture Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu : MAIN MENU : IMAGE BRIGHTNESS CONTRAST SATURATION HUE SHARPNESS PHASE CLOCK 29 35 22 0 16 0 0 : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT Press the VOL+-button, the other item will appear on the screen.
Controls the horizontal position of the picture. V POSITION Controls the vertical position of the picture. AUTO ADJUST Adjusts automatically the display settings to optimize performance in VGA mode. IMAGE MODE This setting controls the overall appearance of the picture, and is chosen from among the following options: STANDARD, BRIGHT, SOFT, MOVE STANDARD, MOVE BRILLIANT. RECALL Restores the original factory settings.
Customizing the Audio Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press the VOL+- buttons to select AUDIO. MAIN MENU : AUDIO BASS TREBLE BALANCE VOLUME 11 11 0 ► RECALL : SELECT MENU : EXIT 34 : SELECT ITEM ENTER: NEXT Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value.
Customizing the Picture Color Settings Press the button to turn the LCD TV on. ENGLISH Press the MENU button to display the Main Menu.Press the VOL+- buttons to select RGB. MAIN MENU : RGB COLOR TEMP RED GREEN BLUE RECALL : SELECT MENU : EXIT USER ► : SELECT ITEM ENTER: NEXT Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value.
Customizing the DISPLAY Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press the VOL+- buttons to select DISPALY. MAIN MENU : DISPLAY DISPLAY MODE: MAIN SOURCE: SUB SOURCE: SWAP MENU SELECT H POSITION V POSITION : SELECT MENU : EXIT 36 FULL TV VGA ► ► ► : SELECT ITEM ENTER: NEXT Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value.
Customizing the OSD Settings Press the button to turn the LCD TV on. ENGLISH Press the MENU button to display the Main Menu.Press the VOL+- buttons to select OSD. MAIN MENU : OSD LANGUAGE TRANSPARENCY OSD TIME OUT : SELECT MENU : EXIT ENGLISH 8 15 SEC : SELECT ITEM ENTER: NEXT Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value.
Customizing the MISC Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press the VOL+- buttons to select MISC. MAIN MENU : MISC SLEEP ASPECT RATIO NOISE REDUCTION IMAGE FREEZE CCD TYPE CCD : SELECT MENU : EXIT OFF FULL MEDIUM OFF CC1 OFF : SELECT ITEM ENTER: NEXT Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value.
Using the PIP/POP/DIGEST Settings The PIP/POP/DIGEST feature allows simultaneous viewing of video from two sources (TV, VCR, DVD etc). Only one source’s audio is played at a time; the user may select which source’s audio is heard. ENGLISH Press the PIP button on the remote control to enter picture-in-picture mode, press again to exit PIP mode. MAIN SUB Press the POP button on the remote control to enter picture-outside-picture mode, press again to exit POP mode.
Using the V-CHIP Settings The US has 2 rating system for viewing content: Movie blocking(MPAA) and TV Blocking. The TV Blocking conjuncts with the V-CHIP to help parents block inappropriate programs from their children. The Movie blocking(MPAA) is used for original movies rated by the Motion Picture Association of America(MPAA) as broadcasted on cable TV and not edited for television. The V-CHIP can also be set to block MPAA-rated movies.
The TV GUIDELINE has 2 rating methods: Content-Based Rating and Age-Based Rating.
Setting the New Password Press the V-CHIP button on the remote control to display the Main menu: PARENTAL CONTROL INPUT 4 DIGITS PIN NUMBER ____ PRESS 0...9 V-CHIP: EXIT Use the PARENTAL CONTROL function, must enter a four-digit password. The factory password is 0000. Pressthe CH+- buttons to select CHANGE PIN CODE, then press ENTER button to enter into setting mode.
Operating the ATSC System Use a supplied antenna cable to connect the ANT.B signal to the LCD TV’s ANT. terminal. Press the ENGLISH button to turn the LCD TV on. Press the ATSC button, press the SETUP button on the remote control. The main menu will appear on the screen. Use the CH+- buttons to select your main menu option. TV/CATV PICTURE SWAP the item. STATION MENU: STATION ► ► ► ► ► Channel Scan Channel Edit Signal Strength Antenna Cable POWER MUTE 3 SOUND TV VIDEO COMP.
CAPTION MENU: CAPTION Caption On/Off Option ► ► Font Setup Font Style Analog ► ► ► OK SETUP SETUP MENU: SETUP Opacity SPDIF Format Default Setting Audio Language Time Zone Menu Language OK 44 ► ► ► ► ► ► SETUP Use the CH+- buttons to highlight an option of the sub-menu, and press the ENTER button. While in adjustment mode, text will turn purple, and use the VOL+- buttons to change the value of the item. Press the SETUP button to exit the menu.
Customizing the STATION Settings Press the button to turn the LCD TV on. ENGLISH Press the SETUP button to display the Main Menu.Press the VOL+- buttons to select STATION. STATION Channel Scan Channel Edit Signal Strength Antenna Cable OK ► ► ► ► ► SETUP Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value. Channel Scan Automatically creates a list of receivable channels.
Customizing the LOCK Settings Press the button to turn the LCD TV on. Press the SETUP button to display the Main Menu.Press the VOL+- buttons to select LOCK. SETUP Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value. Lock On/Off Turns Movie/TV Rating Lock on/off. Movie Rating Selects to use the Movie ratings (refer to page 39).
Customizing the CAPTION Settings Press the button to turn the LCD TV on. ENGLISH Press the SETUP button to display the Main Menu.Press the VOL+- buttons to select CAPTION. CAPTION Caption On/Off Option Font Setup Font Style Analog OK ► ► ► ► ► SETUP Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value. Caption On/Off Turns the Closed Caption on/off.
Customizing the SETUP Settings Press the button to turn the LCD TV on. Press the SETUP button to display the Main Menu.Press the VOL+- buttons to select SETUP. SETUP Opacity SPDIF Format Default Setting Audio Language Time Zone Menu Language 48 OK ► ► ► ► ► ► SETUP Press the CH+- buttons to select the item to control, then press ENTER button to enter into adjustment mode. Press the VOL+- buttons to adjust the desired value.
TROUBLESHOOTING TROUBLESHOOTING ENGLISH Before consulting service personnel, check the following chart for a possible cause of the trouble and for a possible solution. TV will not turn on Make sure the power cord is plugged in, then press the button on the remote. The batteries in the remote control may be exhausted. Replace the batteries. No picture, no sound Check the interface cable between TV and antenna/cable TV. Press the button on the remote.
SPECIFICATION TROUBLESHOOTING Panel System 37 inch Display Resolution 1920 pixels(horizontal) x 1080 pixels (vertical) Television System NTSC and ATSC Antenna Input 75 Ω unbalanced AV IN 2 AV OUT 1 S-VIDEO 2 HDMI /AUDIO YPbPr VGA/AUDIO 50 1 2 1 AUDIO(L/R) IN 4 AUDIO OUT 1 SPEAKER OUT 20 W x 2 POWER SOURCE (Power consumption) 210 W DIMENSION 935 mm (W) x 762 mm (H) x 300 mm (D) WEIGHT 26 KG Troubleshooting and Specifications
Preset Mode Mode Timing Timing ChartG Chart TPreset ENGLISH The screen image has been optimized during manufacture for the display modes listed below. If the signal from the system equals the standard signal mode, the screen is adjusted automatically. If the signal from the system doesn’t equal the standard signal mode, adjust the mode by referring to your videocard user guide otherwise there may be no video, For the display modes listed below, the screen image has been opimized during manufacturer.