CD-RW 5232UI USB 2.
CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 DANGER VORSICHT ATTENTION INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYONS.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents INTRODUCTION ABOUT USB SYSTEM REQUIREMENTS PACKAGE CONTENTS INSTALLATION HARDWARE INSTALLATION DRIVER INSTALLATION Windows Environment SOFTWARE INSTALLATION Windows Environment CONNECTION & OPERATION FRONT PANEL REAR VIEW TECHNICAL DATA TROUBLESHOOTING 1 1 2 2 3 3 4 4 4 4 5 5 6 7 10
CD-RW 5232UI, USB 2.0 External Drive INTRODUCTION Thank you for the purchase of 5232UI, a high-performance external CDReWritable drive of USB 2.0 interface. It supports maximum 52X-speed writing ability on CD-R discs, 32X-speed on CD-RW discs and 52Xspeed reading performance. The drive backs up all writing modes and different CD formats and it automatically recognizes the media placed in the drive, whether a CD, a CD-R or a CD-RW.
CD-RW 5232UI, USB 2.0 External Drive One other benefit of USB is plug and play. That is, when you plug the USB device in, it is automatically detected, drivers installed and then ready for operation USB 2.0 supports data transfer at up to 480Mbps for high-speed devices. It is backward compatible with USB1.1*2 software and peripherals. If your computer doesn’t have a built-in USB 2.0 port, you need to install a USB 2.0 PCI host card in your pc for the CD-RW drive to run at USB 2.O speed.
CD-RW 5232UI, USB 2.0 External Drive INSTALLATION Hardware Installation 1. Connect the power adapter and the AC power cord to the drive. 2. Attach the USB 2.0 cable to the CD-ReWritable drive. USB Connector 3. Attach the other end of the USB 2.0 cable to the USB port in your computer. The drive is now ready to use. If you are installing a USB 2.0 drive, your computer must have a USB 2.0 port to achieve top speed. You may experience slower USB 2.0 drive performance if connected to USB 1.1. 4.
CD-RW 5232UI, USB 2.0 External Drive ♦ It’s advisable not to disconnect the CD-RW drive or unplug the power to the drive while a CD is inserted. ♦ Don’t connect more than two CD-RW drives of USB connections to a single computer. Driver Installation Windows Environment This USB 2.0 External Drive CD-RW 5232UI is a Plug and Play device, and Windows ME/2000/XP can automatically detect the drive and load the appropriate driver.
CD-RW 5232UI, USB 2.0 External Drive CONNECTION & OPERATION Front Panel 1. Headphone Plug By plugging in the headphone jack here, you can listen to an audio CD (CD-DA disc) directly playing from the CD-ReWritable drive. 2. Headphone Volume Control This knob adjusts the audio output level. Turn the wheel to the right to increase the audio volume of your headphone. 3. LED Indicator (dual color) Flashes “green” while verifying or reading a disc. Flashes “amber” while writing a CD-R/CD-RW disc. 4.
CD-RW 5232UI, USB 2.0 External Drive 5. Emergency Eject Hole When the Close/Eject button can’t work properly and the disc tray can’t be opened, you can insert a paper clip or a small rod into this hole for manual ejection. Please make sure to power off the system before you do that. 6. Play/Skip button Press this button to play tracks or skip to next track during the playing state. 7. Close/Eject button This button opens and closes the disc tray. If the tray is closed, pressing the button will eject it.
CD-RW 5232UI, USB 2.
CD-RW 5232UI, USB 2.0 External Drive Disc loading Tray (motorised) Power Requirement input: AC 100~240V, 50/60Hz output: 5V 1.5A, 12V 1.5A RMS output Voltage 0.6 ± 10%Vrms Dimensions Height 44.9~47.6 ± 0.3 mm Width 152.5 ± 0.3 mm Depth 234.5 ± 0.
CD-RW 5232UI, USB 2.
CD-RW 5232UI, USB 2.0 External Drive TROUBLESHOOTING To help you get more familiar with this USB 2.0 external drive, CD-RW 5232UI, the following FAQ lists some common problems you might have. Please read it for reference before you request RMA support from your dealer. Q1. 5232UI cannot be recognized. (1) The drive might not have been connected properly. Please check whether the USB cable and power connector are tightly connected. If yes, do the hot-plugging again.
CD-RW 5232UI, USB 2.0 External Drive Q6. The external speaker doesn’t have sound when playing music CD. (1) Please check if the audio cable is connected to the audio connector properly. (2) Check both rear side of the CD-RW drive and sound card on M/B (If Audio chipset is on board). If they are well connected, check if the sound card is working. Q7. The tray cannot be ejected. There are two possible reasons: (1) Need to be ejected by the application.
CD-RW 5232UI, USB 2.0 External Drive (3) Select good quality and high-speed supported blank discs. (4) Increase main memory capacity. (5) Select other burning software. (6) De-fragment the hard disk. (7) Keep the source & destination discs clean. (no scratches, fingerprints or contamination.) (8) Copy data as image file to hard drive to avoid buffer underrun. (9) Keep the system clean. Do not install redundant driver or application to reduce system loading as well as confliction.
3100551490 Version 1.0 Sep.
