Specifications

Warranty service may only be performed by Pro-Fab Industries or
a Pro-Fab Authorized Empyre Pro Series Furnace Dealer or a Pro-
Fab Authorized Empyre Pro Series Furnace Service Centre.
PRO-FAB INDUSTRIES INC. WARRANTY
Pro-Fab Industries Inc. (hereinafter called “Pro-Fab”) warrants to
the original owner of the Empyre Pro Series Furnace (hereinafter
called the “Empyre Pro Series”) the following:
A two (2) year warranty on the workmanship of the furnace and
workmanship on all parts manufactured by Pro-Fab, from the
consumer date of purchase, and excluding normal wear items
such as (but not limited to) the door gasket, fire brick, insulation,
refractory and exterior finish.
A one (1) year warranty for any labour required for any repair or
replacement of the furnace or parts from the consumer date of
purchase based on Pro-Fab’s predetermined labour rates and
allowable hours.
A limited pro-rated warranty coverage (which includes the one (1)
year labour coverage at Pro-Fab rates and hours as stated above)
for a defective firebox and water jacket only, based on the following
pro-rated scale from the consumer date of purchase:
 • Years one (1) and two (2) – one hundred percent (100%)
coverage;
 • Years three (3), four (4) and five (5) – sixty percent (60%)
coverage;
 •Yearssix(6)andseven(7)–thirtypercent(30%)coverage;
 •Yearseight(8)andnine(9)–fifteenpercent(15%)coverage;
 •Yearten(10)–tenpercent(10%)coverage.
Absolutely no warranty is provided after ten (10) years from the
date of purchase.
Note: All parts NOT manufactured by Pro-Fab carry their own
manufacturer’s warranty. The owner is responsible for all costs
necessary to replace those parts unless covered by the applicable
manufacturer (except for the one (1) year labour coverage at Pro-
Fab rates and hours as stated above).
The above warranties are based on the following factors:
Pro-Fab reserves the right to repair or replace at its discretion any
defective part or furnace, in whole or in part.
Use of Pro-Fab approved water treatment. IMPORTANT: Pro-
Fab approved water treatment is available from your local dealer
or service centre and must be used and validated for warranty
coverage. The pH balance must remain between 8.8 and 11.0, the
nitrite level must remain between 730 and 1460 ppm as NaNO2,
and conductivity must be less than or equal to 4000 mmhos. A copy
of the invoice itemizing the purchase of approved water treatment
will be required as proof of maintenance in the event of a warranty
claim. All laboratory reports must be kept as proof of maintenance
as indicated in the Installation and Operation Instruction Manual.
All instructions in the Empyre Pro Series Installation and Operation
Instruction Manual must be followed.
The water temperature has not dropped below 165°F (74°C) during
operation.
The Warranty Registration and a copy of the original bill (invoice)
must be forwarded to Pro-Fab within thirty (30) days of the date of
purchase to validate the warranty.
Issue Date: May 2012 Part No. 817954R02 Printed in Canada JW0512
10 Year Limited Warranty
Pro-Fab will not be responsible or liable for any of the following: a) If
warranty work requires removal or replacement of all or a part of the
furnace, Pro-Fab is not responsible for the cost of plumbing, freight,
permits, removal or disposal of damaged furnace or parts, replace-
ment of water or additives, labour after the one (1) year warranty
coverage expires, or any cost other than the warrantied replacement
part itself or the furnace; b) The care, maintenance and safe opera-
tion of the Empyre Pro Series Furnace which is the responsibility of
the owner of the furnace; c) Any accidents, injury, damage or loss
incurred due to a heating system failure; d) Any accidents, injury,
damage or loss incurred due to faulty installation, operation or main-
tenance; e) Any cost incurred for replacing or repairing of parts not
manufactured by Pro-Fab which carry their own manufacturer’s war-
ranty (except for the one (1) year labour coverage at Pro-Fab rates
and hours as stated above); f) Any out-of-pocket expenses, alterna-
tive accommodations or loss of revenue due to defective parts or
furnace; g) Performance problems caused by improper sizing of the
furnace, vent connection, or air openings; h) Damages, malfunctions
or failures resulting from the use of any attachment not authorized by
Pro-Fab; i) Units installed outside the continental United States, Alas-
ka, or the provinces or territories of Canada without prior approval
from Pro-Fab; j) Units with their safety certification labels removed;
or k) Damages, malfunctions or failures caused by force majeure,
abuse, accident, fire, or acts of God.
Any available warranty will be void if: a) Maintenance procedures
are not followed as indicated in the Installation and Operation In-
struction Manual page 20; b) Water treatment and proper additives
are not used as specified in the Installation and Operation Instruc-
tion Manual; c) The Empyre Pro Series Furnace has been altered
in any way; d) Any material other than Pro-Fab approved fuel has
been used; e) Any instruction given in the Installation and Opera-
tion Instruction Manual which has not been followed including dur-
ing installation or regular maintenance; or f) Any claim made under
the warranty for a person other than the original owner.
There are no other warranties, expressed or implied, by Pro-Fab
or its Authorized Empyre Pro Series Furnace Dealers or Autho-
rized Empyre Pro Series Furnace Service Centres regarding the
Empyre Pro Series Furnace except the warranty expressed herein.
ANY IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY, OR
FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND
BEYOND THE APPLICABLE WARRANTY PERIODS SPECIFIED
ABOVE. PRO-FAB’S SOLE LIABILITY, WITH RESPECT TO ANY DE-
FECT, SHALL BE AS SET FORTH IN THIS LIMITED WARRANTY,
AND ANY CLAIMS FOR INCIDENTAL OR CONSEQUENTIAL DAM-
AGES ARE EXCLUDED.
No person is authorized to bind Pro-Fab to any other warranty
whatsoever. Pro-Fab reserves the right at any time to make chang-
es or improvements to the design, materials, or specifications of
the Empyre Pro Series line of furnaces or parts without thereby
becoming liable to make similar changes in the furnaces or any of
its parts previously manufactured.
Manufactured by:
Pro-Fab Industries Inc.
Box 112, Arborg, MB R0C 0A0
Empyre Pro Series
Models 200 and 400