User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 2–31
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
• Press the reset or remote reset button on all HSD and HSD-X units installed in
the system. (Not supported in Cooperative or Combined Mode systems.)
When the “reset” or “restart” is completed, the configuration values and parameters are
activated.
Note: In Multi-Channel configurations, the application prompts the user to select the
specific units to reset as shown in the example screen below.
• Press Y (for yes) to reset the HSD-X.
• Press Y (for yes) to reset the HSD.
The configuration values and parameters are now activated.
(1) Verifying Configurations
This section describes how to verify or refer to the HSD system configuration
parameters.
To view the HSD ORT system configuration:
1. In Menu 3, press O.
The List ORT appears.
2. Press O to scroll through the listing.
To view the new system configurations select “List EEPROM” from Menu 3
1. In Menu 3, press L.
2. The List EEPROM appears. Press L to scroll through the listing.
G. Configuring System Parameters using the HSD Owner Requirement Tool
HSD transceivers operating version 7.0 (or later) control processor software and HSD-X
transceivers operating control processor software 6.0, (or later) both support system
configuration using the HSD ORT Tool (PN 1110-SW-1047). The HSD Owner
Requirements Table (ORT) Tool application is available from EMS Technologies. Contact
EMS SATCOM Product Support for more information.
The ORT Tool is a Windows-based program that is used to create and change system
configuration disks or files for the HSD system. The configuration data files, created using
the ORT Tool, are either loaded into the HSD and HSD-X transceivers via the RS-232
maintenance port interface using an HSD load program or loaded using the self-extracting
option of the HSD ORT application.
MENU 2 FIRMWARE Vx.x
A set veh-relative azimuth E set veh-relative elevation
K desired az veh-rel velocity R resume automatic steering
T enter time of day N annotate log file
L re-enter logon password V get firmware versions
Z reset HSD-128 S set satellite longitude
<CTRL> N next menu <CTRL> O previous menu = select reports
TERMINAL: HSD-X NETWORK MODE
HSD-X (y/n) [n] ?
HSD (y/n) [n] ?