User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Page TC–4
18 September 2007
C. Cable Shielding and Termination........................................................................ 3-5
6. ARINC 600 Trays and Connectors............................................................. 3-7
A. Installation Kits ................................................................................................... 3-7
B. Cabling Notes ..................................................................................................... 3-8
(1) HSD Transceiver Cabling .............................................................................. 3-8
(2) HSD-X Transceiver Cabling........................................................................... 3-8
(3) HSD Transceiver Coaxial Cable Loss Considerations .................................. 3-8
7. Mechanical Installation .............................................................................. 3-9
A. General............................................................................................................... 3-9
B. Physical Placement ............................................................................................3-9
C. Environmental Requirements ........................................................................... 3-10
(1) Heating and Cooling .................................................................................... 3-10
D. Chassis Grounding........................................................................................... 3-11
8. Electrical Installation................................................................................ 3-12
A. Section I: Stand-Alone Mode Installation.......................................................... 3-12
(1) Stand-Alone Mode Installations Wiring Notes.............................................. 3-12
B. Section II: Combined (HCM)/Selective Mode Installation................................. 3-28
(1) Combined Mode (HCM)/Selective Mode Installations Wiring Notes............ 3-28
C. Section III: Cooperative Mode Installation........................................................ 3-44
(1) Cooperative Mode Installations Wiring Notes.............................................. 3-44
D. Section IV: Multi-Channel Configuration Installation ........................................ 3-59
(1) Multi-Channel Configuration Installation Wiring Notes ................................ 3-59
9. Outline/Installation and Interconnection/Contact Assignment Diagrams..
3-83
A. Outline/Installation Diagrams............................................................................3-83
B. Interconnection/Contact Assignment Drawings................................................ 3-83
TEST AND FAULT ISOLATION
1. Introduction................................................................................................ 4-1
2. Operational and Diagnostic Testing ......................................................... 4-2
A. General............................................................................................................... 4-2
B. Test and Fault Isolation Equipment Requirements ............................................. 4-2
C. HSD Maintenance Utility Program...................................................................... 4-3