User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–7
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
6. ARINC 600 Trays and Connectors
This section provides detailed information on the ARINC 600 trays provided in the HSD
Installation Kits that are used in the installation of the HSD and HSD-X transceivers.
The HSD LRU is installed in a standard, ARINC 600, 8-MCU tray. Ruggedized trays designed
specifically for installations on Helicopter aircraft are also available.
The HSD-X LRU is typically installed in a standard, 2-MCU tray. Ruggedized trays designed
specifically for installations on Helicopter aircraft are also available.
A. Installation Kits
Installation kits for HSD and HSD-X transceivers are available from EMS Technologies
Ltd. Contact EMS Technologies Sales department for more information on how to select
and order the appropriate HSD Installation Kit.
Table 3–2 lists the recommended installation kits for typical installations.
Table 3–2. HSD and HSD-X Installation Kits
Installation Kit
Name
EMS SATCOM
Part Number
Description
HSD Installation Kit
AC FAN
1110-F-0120-01 Standard Installation Kit: Bottom AC
Fan Tray Assembly and ARINC
Connector (Un-pressurized
Installation)
HSD Installation Kit
DC FAN
1110-F-0120-02 Standard Installation Kit: Bottom DC
Fan Tray Assembly and ARINC
Connector (Un-pressurized
Installation)
HSD Installation Kit
HELICOPTER AC
FAN
1110-F-0120-03 Helicopter Installation Kit: Side AC
Fan Tray Assembly and ARINC
Connector
HSD-X Installation
Kit AC FAN
1110-F-0121-01 Standard Installation Kit: Fan Tray
Assembly with Bottom AC Fan and
ARINC Connectors
HSD-X Installation
Kit NO FAN
1110-F-0121-02 Standard Installation Kit: Tray
Assembly and ARINC Connectors (No
Fan)
HSD-X Installation
Kit HELICOPTER
NO FAN
1110-F-0121-03 Helicopter Installation Kit: Tray
Assembly with Isolators and ARINC
Connectors (No Fan)
HSD/HSD-X COAX
Cable Kit
1110-K-0122 Multi-Channel RF COAX Kit: Tx and
Rx Cables (33ft), Combiners, Splitters,
Isolators, and HSD-X Cables