User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–23
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(j) Stand-Alone Mode Connection Details
The tables in this section provide all top, middle, and bottom plug connection
details for Stand-Alone Mode installations.
BSU BITE A BSU-W(G)
1
Port BSU-W HSD TP2A
STBD BSU-W HSD TP2C
BSU BITE B BSU-X(H) Port BSU-X HSD TP2B
STBD BSU-X HSD TP2D
MULTI-CONTR
OL A
TP3E BSU-T(A) &
HSD TP1A
MULTI-CONTR
OL B
TP3F BSU-U(B) &
HSD TP1B
NOTE
1
:
Letters in (brackets) represent EMS SATCOM AMT-50 BSU pin designations
Top/Port
(T/P):
Refers to Mechanical (fin-mount) High Gain Antenna (HGA) Subsystem
Port:
Refers to Phased Array (Fuselage-mount) or Port side of Dual (side)
Conformal-mount, HGA subsystem
Starboard
(STBD):
Refers to Starboard side of Dual (side) Conformal-mount HGA subsystem
Table 3–10. Stand-Alone Mode ARINC 600 Top Plug Connection Details
I/O
From
Top Plug
Signal Name To Description
I
1A Multi-control A TP3E Multi-control from control
card
I
1B Multi-control B TP3F Multi-control from control
card
I
2A BSU Top/Port
BITE A
(See Note 1)
Mech. Steered Antenna
(MA): BSU, Pin G
1
or W
or
Other Antenna
2
(OA):
BSU,
PORT-W & Starboard-P
ARINC Tx-HI BITE from
Top/Port BSU
I
2B BSU Top/Port
BITE B
MA: BSU, Pin H or X, or
OA
: BSU, PORT-X &
STBD-R
ARINC Tx-LO BITE from
Top/Port BSU
I
2C BSU Starboard
(STBD) BITE A
MA: Not required
OA: BSU, PORT-P &
STBD-W
ARINC Tx-HI BITE from
STBD BSU
Table 3–9. Stand-Alone Mode HSD to BSU Interconnects
Signal Name
Signal Source
Signal
Destination
HSD
Transceiver
Mechanical
HGA
Phased-Array or
Conformal HGA