User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–28
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
B. Section II: Combined (HCM)/Selective Mode Installation
(1) Combined Mode (HCM)/Selective Mode Installations Wiring Notes
This section provides detailed information on the external interface and system
connections involved in the installation of an HSD transceiver for Combined and
Selective Mode operation.
Note: Selective Mode is a non-standard installation and it is not a recommended
mode of operation. Selective Mode has been superseded by Combined Mode
operation for MCS series SATCOM and with Cooperative Mode operation for
SAT-906 series SATCOM. It is recommended that all systems operating in
Selective Mode be upgraded to support Combined or Cooperative Mode as
applicable.
I
7A 10BASE-T Rx+ Ethernet 10BASE-T,
RJ45-3
User Data, Ethernet
10BASE-T
(Available in models
1110-A-0150,
1110-A-0160, and in units
with Service Bulletin,
1110-SB-0004
accomplished)
I
7B 10BASE-T Rx- Ethernet 10BASE-T,
RJ45-6
O
7C 10BASE-T Tx+ Ethernet 10BASE-T,
RJ45-1
O
7D 10BASE-T Tx- Ethernet 10BASE-T,
RJ45-2
O
C1 RF Tx Output Antenna
Subsystem-DLNA
Coax Cable, RF Transmit
Table 3–12. Stand-Alone ARINC 600 Bottom Plug Connection Details
I/O
From
Bottom
Plug
Signal Name To Description
I
BP2 +28 V dc HOT Aircraft Power Source,
HOT
+28 V dc supply
I
BP3 +28 V dc return
GND
Aircraft Power Source,
return
I
BP8 Chassis GND Aircraft Ground Aircraft Chassis Ground
I
BP1 115 V ac HOT Aircraft Power Source,
HOT
115 V ac 400 Hz supply
I
BP7 115 V ac COLD Aircraft Power Source,
COLD
I
BP12 RF Rx Input Antenna
Subsystem-DLNA
Coax Cable, RF
Receive
Table 3–11. Stand-Alone Mode ARINC 600 Middle Plug Connection Details
I/O
From
Middle
Plug
Signal Name To Description